GOST 4028-63
GOST 4028−63 building Nails. The design and dimensions (with Amendments No. 1, 2, 3)
GOST 4028−63
Group В78
INTERSTATE STANDARD
BUILDING NAILS
The design and dimensions
Building nails. Construction and dimensions
ISS 77.140.65
OKP 12 7100
Date of introduction 1964−08−01
INFORMATION DATA
1. DEVELOPED AND INTRODUCED by the Ministry of ferrous metallurgy of the USSR
2. APPROVED AND put INTO EFFECT by the State Committee of standards, measures and measuring instruments of the USSR from
3. INSTEAD 3886−47 GOST, GOST 3887−47, 4028−48 GOST, GOST 4031−48
4. REFERENCE NORMATIVE AND TECHNICAL DOCUMENTS
| The designation of the reference document referenced |
Item number |
| GOST 283−75 |
3 |
5. Limitation of actions taken by Protocol No. 5−94 of the Interstate Council for standardization, Metrology and certification (ICS 11−12−94)
6. EDITION (February 2009) with Amendments No. 1, 2, 3, approved in October 1965, November 1980, December 1987 (IUS 11−65, 2−81, 4−88)
1. The design and dimensions of construction nails with flat heads shall be as specified in the hell.1 and in table.1.
Damn.1. The design and dimensions of construction nails with flat head
Damn.1
Table 1
mm
The diameter of the rod |
The length of a nail |
| 0,8 |
8 |
| 12 | |
| 1,0 |
16 |
| 1,2 | 16 |
| 20 | |
| 25 | |
| 1,4 | 25 |
| 32 | |
| 40 | |
| 1,6 | 25 |
| 40 | |
| 50 |
The symbol construction nails with flat head, rod diameter 1,2 mm and length 25 mm:
P nails 1,2x25 GOST 4028−63
(Changed edition, Rev. N 2).
2. The design and dimensions of nails with a conical head should match those in hell.2−4 and in table.2.
Damn.2. Nails round
Nails round
Damn.2
Damn.3. Nails of clubs
Nails of clubs
Damn.3
Damn.4. Nails of clubs with jumpers
Nails of clubs with jumpers
Damn.4
Table 2
mm
Nominal diameter of the rod |
The length of a nail |
Size |
The smallest head diameter |
| 1,8 | 32 |
- | 3,5 |
| 40 | |||
| 50 | |||
| 60 | |||
| 2,0 | 40 |
1,75 | 4,0 |
| 50 | |||
| 2,5 | 50 |
2,20 | 5,0 |
| 60 | |||
| 3,0 | 70 |
2,65 | 6,0 |
| 80 | |||
| 3,5 | 90 |
3,10 | 7,0 |
| 4,0 | 100 |
3,55 | 7,5 |
| 120 | |||
| 5,0 | 120 |
4,45 | 9,0 |
| 150 | |||
| 6,0 | 150 |
5,30 | 11,0 |
| 200 | |||
| 8,0 | 250 |
7,13 | 14,0 |
Note. At the request of the consumer nails round 1,8х32 produce a flat head.
The symbol of nails with a conical head, circular, with a diameter of 2.5 mm and a length of 60 mm:
Nails To 2,5х60 GOST 4028−63
The same, of clubs:
Nails vol 2,5х60 GOST 4028−63
The same clubs with the jumpers:
Nails TP 2,5х60 GOST 4028−63
(Changed edition, Rev. N 1, 2).
3. Technical requirements for nails according to GOST 283.
Note. Unilateral uniform bending of a rod in the middle of the nail size (1,8h60) mm shall not exceed 0.7 mm.
(Changed edition, Rev. N 1, 2).
4. Theoretical mass of nails specified in the application.
(Added, Rev. N 2).
APP
Reference
Theoretical mass of nails
The size of the nails |
The round mass of 1000 nails, kg |
| 0,8x8 |
0,032 |
| 0,8x12 |
0,051 |
| 1,0х16 |
0,100 |
| 1,2x16 |
0,147 |
| 1,2x20 |
0,183 |
| 1,2x25 |
Of 0.219 |
| 1,4x25 |
0,302 |
| 1,4х32 |
0,385 |
| 1,4x40 |
0,482 |
| 1,6x25 |
0,397 |
| 1,6х40 |
0,633 |
| 1,6x50 |
0,791 |
| 1,8х32 |
0,640 |
| 1,8х40 |
0,787 |
| 1,8х50 |
0,967 |
| 1,8h60 |
1,160 |
| 2,0h40 |
0,949 |
| 2,0х50 |
1,190 |
| 2,5x50 |
1,870 |
| 2,5х60 |
2,230 |
| 3,0х70 |
3,770 |
| 3,0x80 |
4,330 |
| 3,5х90 |
6,600 |
| 4,0h100 |
9,500 |
| 4,0х120 |
11,500 |
| 5,0х120 |
17,800 |
| 5,0х150 |
21,900 |
| 6,0х150 |
32,400 |
| 6,0х200 |
43,100 |
| 8,0х250 |
96,200 |
Note. The mass of 1000 diamonds nails by 15%, and of clubs with the ridges 12% less than the mass of 1000 round nails of the same size.
APP. (Changed edition, Rev. N 1−3).
