Copper rod, wire, pipe, sheet, strip made of C12500 - Cw006a
Equivalent
| Grade | analogue | W. Nr. | Aisi Uns | En | Order |
|---|---|---|---|---|---|
| M2 | Buy from stock, view availability |
Relevance
Copper is the most widespread non-iron metal. It possesses high corrosive resistance at normal atmospheric conditions — in sea, fresh water or various aggressive environments. Despite this, copper is non-resistant in environment of ammonia and sulfur dioxide. It can be easily brazed and pressure treated. Possessing low casting properties, copper is hardly welded and cut. Usually, it is used in a form of pipes, busbars, sheets, bars, wire.
Technical characteristics of C12500
C12500 — Cw006a — is an ultimate copper with low quantity of different residual elements. Plumb, arsenic, nickel, iron, sulfur, antimony, tin, bismuth are also presented in composition. Content of oxygen constitutes 0,05−0,08%. C12500 grade has high electric and heat conductivity, plasticity, corrosive resistance. Alloying components (phosphorus, nickel, etc.) influence on technical characteristics of copper. Copper grades differ depending on manufacturing method. By its physical characteristics, copper is divided into soft and hard.
Industrial usage: manufacture of copper basis alloys, high-quality pressure-treated semi-fabricates, air conditioners and part of cryogenic equipment.
Percentage composition
| Element | Content |
| Cu | 99.7 |
| Pb | <0,01 |
| Ni | <0,2 |
| Fe | <0,05 |
| S | <0,01 |
| As | <0,01 |
| Sb | <0,005 |
| O | <0,07 |
| Sn | <0,05 |
| Bi | <0,002 |
Main properties
Casting temperature = 1150 — 1250°C
Point of melting = 1083°C
Alloy hardness: HB 10 -1 = 45 MPа
Coefficient of friction with lubricant = 0.011
Coefficient of friction without lubricant = 0.43
Mechanical characteristics at a temperature of 20 °C
| Mill-products | ψ % | KCU kJ/m2 |
δ5 (%) | YS (MPa) | TS (MPa) |
| soft alloy | 60 | 90−150 | 200−250 | ||
| hard alloy | 6 | 300−450 | 400−490 |
YS — permanent change of form — yield strength (proportionality), MPa
TS — ultimate tensile strength (rupture strength), MPa
Casting and technological copper properties
| Description | Identification |
| Casting temperature: | 1150 — 1250°C |
| Linear shrinkage: | 2,1% |
| Melting point: | 1083°C |
Physical characteristics
R 10 9(Ohm-m) |
J/(kg/degree) | r (kg/m3) |
l (V/(m-Degree)) | a 10 -6 (1/Degree) |
E 10— -5 (MPa) |
T (Degree) |
| 17,8 | 390 | 8940 | 387 | 1,32 | 20 | |
| 16,7 | 1,28 | 100 |
Foreign analogs of copper C12500
| Austria | Czech Republic | Japan | the USA | Poland |
| Cu-C | 423 004 | C1821 | C12500 | Cu99,7G |
| ONORM | CSN | JIS | - | PN |
| Description | Identification | Description | Identification |
| — differential deposit at a process of first crack appearing, % | å | — heating capacity of alloy (heat conduction coefficient), V/(m°С) | l |
| — maximum shear stress, ultimate torsional strength, MPa | Jê | — elastic strength, MPa | σ0,05 |
| — ultimate bending strength, MPa | σ bend | — conventional yield limit, MPa | σ0,2 |
| — fatigue endurance limit during bending test with symmetrical load cycle, MPa | σ-1 | — percentage elongation after rupture, % | δ5,δ4,δ10 |
| — fatigue endurance limit during torsion test with symmetrical load cycle, MPa | J-1 | — yield point (contraction), MPa | YS 0,05 |
| — amount of load cycling | n | — relative shear, % | v |
| — specific electrical resistance, Ohm-m | R and ρ | — short ultimate tensile strength, MPa | sv |
| — standard module of elasticity HPa | E | — contraction ratio, % | ψ |
| — properties getting temperature, Degree | T | — impact hardness, which is established on specimens with concentrators in accordance with V and U types, J/cm2 | KCU and KCV |
| — specific heat of alloy (temperature range is 20°С), [J/(kg-deg)] | C | — Brinell hardness | HB |
| — density, kg/m3 | pn and r | — Vicker’s hardness | HV |
| — linear thermal expansion coefficient (in a temperature range of 20°С), 1/°С | a | — Rockwell hardness C | HRC |
| — long-time strength limit, MPa | σtТ | — Rockwell hardness B | HRB |
| — module of elasticity at a process of torsional shear, HPa | G | — Shore hardness | HSD |
C12500 — Cw006a supplier
«Auremo» C12500 — Cw006a supplier proposes to buy products for the most favorable C12500 — Cw006a price. A wide range of high-quality goods is presented in stock. They comply with GOST and International Standards of quality. Our offices located in Moscow, St. Petersburg and cities of Central Europe provide availability of products and efficiency of delivery. You can easily buy С12500 pipe, wire, rod, strip. C12500 — Cw006a price depends on order quantity and additional conditions of supply. If you buy C12500 — Cw006a by wholesale, you will be given special discounts.
Buy C12500 — Cw006a at a bargain price
All products are certificated. A quality is guaranteed by rigorous technology compliance of a manufacture. Our managers are always ready to answer any questions and to give a knowledgeable assistance. You can easily buy C12500 — Cw006a by connecting us with a convenient way for you. Phone numbers, e-mail addresses of the closest company’s offices are located in section «Contacts». Order a service «Call-back» and our manager will help you to choose products that will fit your individual requirements. C11000 — 2.0090 rod, wire, pipe, strip are always in stock. We have the most affordable C12500 — Cw006a price from C12500 — Cw006a supplier. A quality complies with GOST (all-Union State Standards) and International Standards.
