GOST 8509-93

GOST 27772-2015 GOST P 52927-2015 GOST P 56354-2015 GOST P 56355-2015 GOST 30245-2012 GOST 32603-2012 GOST 24045-2016 GOST 8509-93 GOST 8283-93 GOST 8240-97 GOST 5257-98 GOST 30245-2003 GOST 24045-94 GOST 19772-93 GOST 19771-93 GOST 14635-93 GOST 8319.4-75 GOST 8319.13-75 GOST 8320.6-83 GOST 8320.2-83 GOST 8320.3-83 GOST 5267.8-90 GOST 5267.1-90 GOST 12492.4-90 GOST 12492.1-90 GOST 30565-98 GOST 5422-73 GOST 7511-73 GOST 9234-74 GOST 19425-74 GOST 8319.8-75 GOST 8319.5-75 GOST 8319.0-75 GOST 21026-75 GOST 8319.6-75 GOST 11474-76 GOST 13229-78 GOST 8281-80 GOST 8278-83 GOST 8320.10-83 GOST 8282-83 GOST 8320.9-83 GOST 8320.13-83 GOST 12492.15-90 GOST 5267.6-90 GOST 5267.0-90 GOST 5267.11-90 GOST 8319.12-75 GOST 10551-75 GOST 8319.11-75 GOST 25577-83 GOST 8320.4-83 GOST 8320.12-83 GOST 8320.0-83 GOST 5157-83 GOST 8320.5-83 GOST 26020-83 GOST 8320.11-83 GOST 4781-85 GOST 5267.2-90 GOST 12492.7-90 GOST 5267.9-90 GOST 12492.0-90 GOST 12492.10-90 GOST 12492.12-90 GOST 5267.12-90 GOST 8319.2-75 GOST 8320.7-83 GOST 8320.8-83 GOST 18662-83 GOST 8320.1-83 GOST 8510-86 GOST 8239-89 GOST 17152-89 GOST 12492.6-90 GOST 5267.10-90 GOST 12492.2-90 GOST 5267.4-90 GOST 5267.13-90 GOST 12492.5-90 GOST 12492.3-90 GOST 12492.8-90 GOST 5267.3-90 GOST 12492.14-90 GOST 12492.9-90 GOST 5267.7-90 GOST 12492.11-90 GOST 12492.13-90 GOST 5267.5-90

gost-8509-93.pdf (449.76 KiB)
ГОСТ 8509-93

Corners steel hot-rolled equilateral. Assortment

GOST 8509−93

Group B22

INTERSTATE STANDARD

STAINLESS STEEL HOT STAINLESS STEEL

Assortment

Hot-rolled steel equal-leg angles. Dimensions

ISS 77.140.70
OKP 09 3100, 09 3200, 09 3300

Date of introduction 1997−01−01

Foreword

1 DEVELOPED by the Ukrainian Research Institute of Metals

GOSSTANDARD of Ukraine

2 ADOPTED by the Interstate Council for Standardization, Metrology and certification (Minutes No. 3 of 17 February 1993)

For the adoption voted:

State name	Name of national body for standardization
Republic of Armenia	Armgosstandart
Republic of Belarus	Belstandart
The Republic of Kazakhstan	State Standard of the Republic of Kazakhstan
The Republic of Moldova	Moldovastandard
Russian Federation	Gosstandart of Russia
Turkmenistan	TurkmenGlavgosinspection
The Republic of Uzbekistan	Uzgosstandart
Ukraine	Gosstandart of Ukraine

3 Decree of the Committee of the Russian Federation for Standardization, Metrology and Certification of February 20, 1996 N 85 interstate standard GOST 8509−93 was introduced directly as a state standard of the Russian Federation from January 1, 1997.

4 SUBSTITUTE GOST 8509−86

5 REVISION. August 2012

1 This standard applies to steel hot-rolled equal-angle corners.

Figure 1 Corner dimensions, cross-sectional area, reference values for axes and mass of 1 m corners

2 The dimensions of the corners, the cross-sectional area, the reference values for the axes and the mass of 1 m of the corners should correspond to those indicated in Figure 1 and Table 1, and for export — to annexes A and B.

Corners steel hot-rolled equilateral. Assortment

Picture 1

Table 1

Number of corner					, cm	Reference values of values for axes										Weight 1 m, kg
mm												, cm	, cm
, cm	, cm	, cm	max, cm	max, cm	min, cm	, cm	min, cm
2	20	3	3.5	1.2	1.13	0.40	0.28	0.59	0.63	0.75	0.17	0.20	0.39	0.23	0.60	0.89
4	3.5	1.2	1.46	0.50	0.37	0.58	0.78	0.73	0.22	0.24	0.38	0.28	0.64	1.15
2.5	25	3	3.5	1.2	1.43	0.81	0.46	0.75	1.29	0.95	0.34	0.33	0.49	0.47	0.73	1.12
4	3.5	1.2	1.86	1.03	0.59	0.74	1.62	0.93	0.44	0.41	0.48	0.59	0.76	1.46
2.8	28	3	4.0	1.3	1.62	1.16	0.58	0.85	1.84	1.07	0.48	0.42	0.55	0.68	0.80	1.27
3	thirty	3	4.0	1.3	1.74	1.45	0.67	0.91	2.30	1.15	0.60	0.53	0.59	0.85	0.85	1.36
4	4.0	1.3	2.27	1.84	0.87	0.90	2.92	1.13	0.77	0.61	0.58	1.08	0.89	1.78
3.2	32	3	4,5	1.5	1.86	1.77	0.77	0.97	2.80	1.23	0.74	0.59	0.63	1.03	0.89	1.46
4	4,5	1.5	2.43	2.26	1.00	0.96	3.58	1.21	0.94	0.71	0.62	1.32	0.94	1.91
3.5	35	3	4,5	1.5	2.04	2.35	0.93	1.07	3.72	1.35	0.97	0.71	0.69	1.37	0.97	1.60
4	4,5	1.5	2.67	3.01	1.21	1.06	4.76	1.33	1.25	0.88	0.68	1.75	1.01	2.10
5	4,5	1.5	3.28	3.61	1.47	1.05	5.71	1.32	1.52	1.02	0.68	2.10	1.05	2.58
4	40	3	5.0	1.7	2.35	3.55	1.22	1.23	5.63	1.55	1.47	0.95	0.79	2.08	1.09	1.85
4	5.0	1.7	3.08	4.58	1.60	1.22	7.26	1.53	1.90	1.19	0.78	2.68	1.13	2.42
5	5.0	1.7	3.79	5.53	1.95	1.21	8.75	1.52	2.30	1.39	0.78	3.22	1.17	2.98
4,5	45	3	5.0	1.7	2.65	5.13	1.56	1.39	8.13	1.75	2.12	1.24	0.89	3.00	1.21	2.08
4	5.0	1.7	3.48	6.63	2.04	1.38	10.52	1.74	2.74	1.54	0.89	3.89	1.26	2.73
5	5.0	1.7	4.29	8.03	2.51	1.37	12.74	1.72	3.33	1.81	0.88	4.71	1.30	3.37
5	50	3	5.5	1.8	2.96	7.11	1.94	1.55	11.27	1.95	2.95	1.57	1.00	4.16	1.33	2.32
4	5.5	1.8	3.89	9.21	2.54	1.54	14.63	1.94	3.80	1.95	0.99	5.42	1.38	3.05
5	5.5	1.8	4.80	11.20	3.13	1.53	17.77	1.92	4.63	2.30	0.98	6.57	1.42	3.77
6th	5.5	1.8	5.69	13.07	3.69	1.52	20.72	1.91	5.43	2.63	0.98	7.65	1.46	4.47
5.6	56	4	6.0	2.0	4.38	13.10	3.21	1.73	20.79	2.18	5.41	2.52	1.11	7.69	1.52	3.44
5	6.0	2.0	5.41	15.97	3.96	1.72	25.36	2.16	6.59	2.97	1.10	9.41	1.57	4.25
6.3	63	4	7.0	2.3	4.96	18.86	4.09	1.95	29.90	2.45	7.81	3.26	1.25	11.00	1.69	3.90
5	7.0	2.3	6,13	23.10	5.05	1.94	36.80	2.44	9.52	3.87	1.25	13.70	1.74	4.81
6th	7.0	2.3	7.28	27.06	5.98	1.93	42.91	2.43	11.18	4.44	1.24	15.90	1.78	5.72
7th	70	4,5	8.0	2.7	6.20	29.04	5.67	2.16	46.03	2.72	12.04	4.53	1.39	17.00	1.88	4.87
5	8.0	2.7	6.86	31.94	6.27	2.16	50.67	2.72	13.22	4.92	1.39	18.70	1.90	5.38
6th	8.0	2.7	8.15	37.58	7.43	2.15	59.64	2.71	15.52	5.66	1.38	22.10	1.94	6.39
7th	8.0	2.7	9.42	42.98	8.57	2.14	68.19	2.69	17.77	6.31	1.37	25.20	1.99	7.39
8	8.0	2.7	10.67	48.16	9.68	2.12	76.35	2.68	19.97	6.99	1.37	28.20	2.02	8.37
7.5	75	5	9.0	3.0	7.39	39.53	7.21	2.31	62.65	2.91	16.41	5.74	1.49	23.10	2.02	5.80
6th	9.0	3.0	8.78	46.57	8.57	2.30	73.87	2.90	19.28	6.62	1.48	27.30	2.06	6.89
7th	9.0	3.0	10.15	53.34	9.89	2.29	84.61	2.89	22.07	7.43	1.47	31.20	2.10	7.96
8	9.0	3.0	11.50	59.84	11.18	2.28	94.89	2.87	24.80	8.16	1.47	35.00	2.15	9.02
9	9.0	3.0	12.83	66.10	12.43	2.27	104.72	2.86	27.48	8.91	1.46	38.60	2.18	10.07
8	80	5.5	9.0	3.0	8.63	52.68	9.03	2.47	83.56	3.11	21.80	7.10	1.59	30.90	2.17	6.78
6th	9.0	3.0	9.38	56.97	9.80	2.47	90.40	3.11	23.54	7.60	1.58	33.40	2.19	7.36
7th	9.0	3.0	10.85	65.31	11.32	2.45	10.60	3.09	26.97	8.55	1.58	38.30	2.23	8.51
8	9.0	3.0	12.30	73.36	12.80	2.44	116.39	3.08	30.32	9.44	1.57	43.00	2.27	9.65
9	90	6th	10.0	3.3	10.61	82.10	12.49	2.78	130.00	3.50	33.97	9.88	1.79	48.10	2.43	8.33
7th	10.0	3.3	12.28	94.30	14.45	2.77	149.67	3.49	38.94	11.15	1.78	55.40	2.47	9.64
8	10.0	3.3	13.93	106.11	16.36	2.76	168.42	3.48	43.80	12.34	1.77	62.30	2.51	10.93
9	10.0	3.3	15.60	118.00	18.29	2.75	186.00	3.46	48.60	13.48	1.77	68.00	2.55	12.20
10	100	6.5	12.0	4.0	12.82	122.10	16.69	3.09	193.46	3.89	50.73	13.38	1.99	71.40	2.68	10.06
7th	12.0	4.0	13.75	130.59	17.90	3.08	207.01	3.88	54.16	14.13	1.98	76.40	2.71	10.79
8	12.0	4.0	15.60	147.19	20.30	3.07	233.46	3.87	60.92	15.66	1.98	86.30	2.75	12.25
10	12.0	4.0	19.24	178.95	24.97	3.05	283.83	3.84	74.08	18.51	1.96	110.00	2.83	15.10
12	12.0	4.0	22.80	208.90	29.47	3.03	330.95	3.81	86.84	21.10	1.95	122.00	2.91	17.90
14	12.0	4.0	26.28	237.15	33.83	3.00	374.98	3.78	99.32	23.49	1.94	138.00	2.99	20.63
16	12.0	4.0	29.68	263.82	38.04	2.98	416.04	3.74	111.61	25.79	1.94	152.00	3.06	23.30
eleven	110	7th	12.0	4.0	15.15	175.61	21.83	3.40	278.54	4.29	72.68	17.36	2.19	106.00	2.96	11.89
8	12.0	4.0	17.20	198.17	24.77	3.39	314.51	4.28	81.83	19.29	2.18	116.00	3.00	13.50
12.5	125	8	14.0	4.6	19.69	294.36	32.20	3.87	466.76	4.87	121.98	25.67	2.49	172.00	3.36	15.46
9	14.0	4.6	22.00	327.48	36.00	3.86	520.00	4.86	135.88	28.26	2.48	192.00	3.40	17.30
10	14.0	4.6	24.33	359.82	39.74	3.85	571.04	4.84	148.59	30.45	2.47	211.00	3.45	19.10
12	14.0	4.6	28.89	422.23	47.06	3.82	670.02	4.82	174.43	34.94	2.46	248.00	3.53	22.68
14	14.0	4.6	33.37	481.76	54.17	3.80	763.90	4.78	199.62	39.10	2.45	282.00	3.61	26.20
16	14.0	4.6	37.77	538.56	61.09	3.78	852.84	4.75	224.29	43.10	2.44	315.00	3.68	29.65
14	140	9	14.0	4.6	24.72	465.72	45.55	4.34	739.42	5.47	192.03	35.92	2.79	274.00	3.76	19.41
10	14.0	4.6	27.33	512.29	50.32	4.33	813.62	5.46	210.96	39.05	2.78	301,00	3.82	21.45
12	14.0	4.6	32.49	602.49	59.66	4.31	956.98	5.43	248.01	44.97	2.76	354.00	3.90	25.50
16	160	10	16.0	5.3	31,43	774.24	66.19	4.96	1229.10	6.25	319.33	52.52	3.19	455.00	4.30	24.67
eleven	16.0	5.3	34.42	844.21	72.44	4.95	1340.06	6.24	347.77	56.53	3.18	496.00	4.35	27.02
12	16.0	5.3	37.39	912.89	78.62	4.94	1450,00	6.23	375.78	60.53	3.17	537.00	4.39	29.35
14	16.0	5.3	43.57	1046.47	90.77	4.92	1662.13	6.20	430.81	68.15	3.16	615.00	4.47	34.20
16	16.0	5.3	49.07	1175.19	102.64	4.89	1865.73	6.17	484.64	75.92	3.14	690,00	4.55	38.52
18	16.0	5.3	54.79	1290.24	114.24	4.87	2061.03	6,13	537.46	82.08	3.13	771.00	4.63	43.01
20	16.0	5.3	60.40	1418.85	125.60	4.85	2,248.26	6.10	589.43	90.02	3.12	830.00	4.70	47.41
18	180	eleven	16.0	5.3	38.80	1216.44	92.47	5.60	1933.10	7.06	499.78	72.86	3.59	716.00	4.85	30.47
12	16.0	5.3	42.19	1316.62	100.41	5.59	2092,78	7.04	540.45	78.15	3.58	776.00	4.89	33.12
20	200	12	18.0	6.0	47.10	1822.78	124.61	6.22	2896.16	7.84	749.40	98.68	3.99	1073.00	5.37	36.97
13	18.0	6.0	50.85	1960,77	134.44	6.21	3116.18	7.83	805.35	105.07	3.98	1156.00	5.42	39.92
14	18.0	6.0	54.60	2097,00	144.17	6.20	3333.00	7.81	861.00	111.50	3.97	1236.00	5.46	42.80
16	18.0	6.0	61.98	2362.57	163.37	6.17	3755.39	7.78	969.74	123.77	3.96	1393.00	5.54	48.65
20	18.0	6.0	76.54	2871.47	200.37	6.12	4860.42	7.72	1181,92	146.62	3.93	1689.00	5.70	60.08
25	18.0	6.0	94.29	3466.21	245.59	6.06	5494.04	7.63	1438.38	172.68	3.91	2028.00	5.89	74.02
thirty	18.0	6.0	111.54	4019.60	288.57	6.00	6351.05	7.55	1698.16	193.06	3.89	2332,00	6.07	87.56
22	220	14	21.0	7.0	60.38	2814.36	175.18	6.83	4470.15	8.60	1158.56	138.62	4.38	1655,00	5.91	47.40
16	21.0	7.0	68.58	3175.44	198,71	6.80	5045.37	8.58	1305.52	153.34	4.36	1869.00	6.02	53.83
25	250	16	24.0	8.0	78.40	4717.10	258.43	7.76	7492.10	9.78	1942.09	203.45	4.98	2775.00	6.75	61.55
18	24.0	8.0	87.72	5247.24	288.82	7.73	8336.69	9.75	2157.78	223.39	4.96	3089.00	6.83	68.86
20	24.0	8.0	96.96	5764.87	318.76	7.71	9159.73	9.72	2370.01	242.52	4.94	3395.00	6.91	76.11
22	24.0	8.0	106.12	6270.32	348.26	7.69	9961,30	9.69	2579.04	260.52	4.93	3691,00	7.00	83.31
25	24.0	8.0	119.71	7006.39	391.72	7.65	11125.52	9.64	2887.26	287.14	4.91	4119.00	7.11	93.97
28	24.0	8.0	133.12	7,716.86	434.25	7.61	12243.84	9.59	3189.89	311.98	4.90	4527,00	7.23	10.50
thirty	24.0	8.0	141.96	8176.82	462.11	7.59	12964.66	9.56	3388.98	327.82	4.89	4788.00	7.31	111.44
35	24.0	8.0	163.71	9281.05	530.11	7.53	14682.73	9.47	3879.37	366.13	4.87	5401.68	7.53	128.51

Notes

1. The cross-sectional area and reference values are calculated by nominal dimensions. The density of steel is 7.85 g / cm .

2. The rounding radii shown in figure 1 and in table 1 are given for the construction of the gauge and are not monitored on the profile.

Legend to Figure 1 and Table 1:

— shelf width;

— thickness of the shelf;

— radius of internal curvature;

— radius of curvature of shelves;

— cross-sectional area;

— moment of inertia;

— distance from the center of gravity to the outer edge of the shelf;

— centrifugal moment of inertia;

is the radius of inertia.

3 For the accuracy of rolling, the corners are made:

A — high accuracy;

B — the usual accuracy.

4 The maximum deviation from the size of the corners should not exceed those indicated in Table 2.

table 2

Number of corner				Limiting deviations, mm
by shelf width	Shelf thickness
up to 6 inclusive.		from 6,5 to 9 inclusive.		over 9
A	AT	A	AT	A	AT
From	2	before	4,5	± 1.0	+0.2 -0.3	+0.3 -0.4	-	-	-	-
"	5	"	9	± 1.5	+0.2 -0.4	+0.3 -0.5	+0.2 -0.5	+0.3 -0.6	+0.3 -0.5	+0.4 -0.6
"	10	"	15	± 2.0	-	-	+0.3 -0.5	+0.4 -0.6	+0.3 -0.6	+0.4 -0.7
"	16	"	20	± 3.0	-	-	-	-	+0.4 -0.7	+0.5 -0.8
"	22	"	25	± 4.0	-	-	-	-	+0.4 -0.8	+0.5 -0.9

5 As agreed by the manufacturer with the customer, it is allowed to make corners with a shift in the limiting deviations along the thickness of the shelf within the limits of tolerances of the corresponding accuracy.

6 As agreed with the customer, the thickness deviation of the shelf may be replaced by the maximum deviations in mass according to Table 3.

Table 3

Number of corner	Limit deviations by weight,%
I class	Grade II
From 2 to 7.5 inclusive.	+3 -5	+3 -5
More than 7.5	± 2.5

7 The deviation from the right angle at the apex shall not exceed 35 '.

As agreed by the manufacturer with the consumer, the deviation from the right angle at the top should not exceed:

1,0 mm — for corners with shelf width up to 50 mm inclusive;

2,0 mm — for corners with a shelf width exceeding 50 to 100 mm inclusive;

3,0 mm — for corners with a shelf width of more than 100 to 200 mm.

8 Dulling of external corners (including the angle at the top) is not controlled.

At the request of the consumer, blunting of external angles (including the angle at the top) should not exceed:

0,3 shelf thickness — for corners thickness up to 10 mm inclusive;

3,0 mm — for corners thicker than 10 to 16 mm inclusive;

5,0 mm — for corners with thickness over 16 mm.

9 Corners are made in length from 4 to 12 m:

dimensional length;

dimensional length with an inordinate amount of not more than 5% batch weight;

a multiple of the measured length,

of a multiple dimensional length with an inordinate amount of not more than 5% of the batch weight;

unlimited length;

limited length within the dimensionless.

9.1 As agreed by the manufacturer with the customer, the corners are produced in a measured and multiple dimensional length with non-dimensional lengths of more than 5% batch weight.

9.2 It is allowed to produce corners with a length of at least 3 m and more than 12 m.

10 Limit deviations along the length of corners of a dimensional length or a multiple dimensional should not exceed:

+30 mm — with a length of up to 4 m inclusive;

+50 mm — for a length exceeding 4 to 6 m inclusive;

+70 mm — for lengths exceeding 6 m.

At the request of the customer for angles longer than 4 to 7 m, the maximum length deviations should not exceed +40 mm, more than 7 m — + 5 mm for each following meter.

11 The curvature of the corners should not exceed 0.4% of the length.

At the request of the consumer, corners are produced whose curvature does not exceed 0.2% of the length. For corners from N 2 to 4.5 inclusive, the curvature is checked for a length of 1 m.

12 The dimensions of the cross-section of the corners, the blunting of the corners are measured at a distance of at least 500 mm from the end of the rod.

APPENDIX A
(recommended)

PROFILES STEEL HOT

Part 1. Corners are equal. Dimensions (ISO 657−1-89 *)

________________
* Access to international and foreign documents, mentioned here and below in the text, can be obtained by clicking on the link. — Note of the database manufacturer.

1 Area of distribution

This part of ISO 657 includes dimensions of hot-rolled equal-angle corners.

2 This standard contains the terms of this part of ISO 657. As of publication, this publication was current.

All standards are revised, so it is necessary to use the standards of the latest edition.

Member countries of IEC and ISO should be provided with current international standards.

ISO 657−5-76. Hot-rolled steel profiles, part 5. Equal and unequal corners, marginal deviations in metric and inch series.

3 Dimensions

3.1 Preferred sizes are in bold.

3.2 The internal rounding radii are given for information and are given in Table A.1.

3.3 The radius of the curvature of the shelves is not defined, but can be calculated if necessary.

4 Profile properties

The mass, cross-sectional area and reference values of the values of the equal-angle corners are given for information in Table A.1 and are calculated under the condition that the radius of the rounding of the shelves has ½ the radius of the inner curvature.

5 Tolerances

Dimensional tolerances are given in Table B.1 of Appendix B.

Corners steel hot-rolled equilateral. Assortment

Table A.1

The size	Weight, kg / m	, cm	The values			Distance from center of gravity			Reference values of values for axes

, mm	, mm	, mm	, cm	, cm	, cm	, cm	, cm	, cm	, cm	, cm	, cm	, cm	, cm
20x20x3	0.88	1.12	20	3	3.5	0.598	1.41	0.846	0.392	0.590	0.279	0.618	0.742	0.165	0.383	0.195
25x25x3	1.12	1.42	25	3	3.5	0,723	1.77	1.02	0.803	0.751	0.452	1.27	0.945	0.334	0.448	0.326
25x25x4	1.45	1.85	25	4	3.5	0.762	1.77	1.08	1.02	0.741	0.586	1.61	0.931	0.430	0.482	0.399
30x30x3	1.36	1.74	thirty	3	5	0.835	2.12	1.18	1.40	0.899	0.649	2.22	1.13	0.585	0.581	0.496
30х30х4	1.78	2.27	thirty	4	5	0.878	2.12	1.24	1.80	0.892	0,850	2.85	1.12	0.754	0.577	0.607
35х35х4	2.09	2.67	35	4	5	1.00	2.47	1.42	2.95	1.05	1.18	4.68	1.32	1.23	0.678	0.865
35x35x5	2.57	3.28	35	5	5	1.04	2.47	1.48	3.56	1.04	1.45	5.64	1.31	1.49	0.675	1.01
40х40х3	1.84	2.35	40	3	6th	1.07	2.83	1.52	3.45	1.21	1.18	5.45	1.52	1.44	0.783	0.949
40х40х4	2.42	3.08	40	4	6th	1.12	2.83	1.58	4.47	1.21	1.55	7.09	1.52	1.86	0.777	1.17
40х40х5	2.97	3.79	40	5	6th	1.16	2.83	1.64	5.43	1.20	1.91	8.60	1.51	2.26	0.773	1.38
45х45х4	2.74	3.49	45	4	7th	1.23	3.18	1.75	6.43	1.36	1.97	10.2	1.71	2.68	0.876	1.53
45х45х5	3.38	4.30	45	5	7th	1.28	3.18	1.81	7.84	1.35	2.43	12.4	1.70	3.26	0.871	1.80
50х50х4	3.06	3.89	50	4	7th	1.36	3.54	1.92	8.97	1.52	2.46	14.2	1.91	3.73	0.979	1.94
50х50х5	3.77	4.80	50	5	7th	1.40	3.54	1.99	11.0	1.51	3.05	17.4	1.90	4.55	0.973	2.29
50х50х6	4.47	5.69	50	6th	7th	1.45	3.54	2.04	12.8	1.50	3.61	20.3	1.89	5.34	0.968	2.61
60х60х5	4.57	5.82	60	5	8	1.64	4.24	2.32	19.4	1.82	4.45	30.7	2.30	8.03	1.17	3.46
60x60x6	5.42	6.91	60	6th	8	1.69	4.24	2.39	22.8	1.82	5.29	36.1	2.29	9.44	1.17	3.96
60x60x8	7.09	9.03	60	8	8	1.77	4.24	2.50	29.2	1.80	6.89	46.1	2.26	12.2	1.16	4.86
65x65x6	5.91	7.53	65	6th	9	1.80	4.60	2.55	29.2	1.97	6.21	46.3	2.48	12.1	1.27	4.74
65х65х8	7.73	9.85	65	8	9	1.89	4.60	2.67	37.5	1.95	8.13	59.4	2.46	15.6	1.26	5.84
70x70x6	6.38	8.13	70	6th	9	1.93	4.95	2.73	36.9	2.13	7.27	58.5	2.68	15.3	1.37	5.60
70x70x7	7.38	9.40	70	7th	9	1.97	4.95	2.79	42.3	2.12	8.41	67.1	2.67	17.5	1.36	6.28
75х75х6	6.85	8.73	75	6th	9	2.05	5.30	2.90	45.8	2.29	8.41	72.7	2.89	18.9	1.47	6.53
75х75х8	8.99	11.4	75	8	9	2.14	5.30	3.02	59.1	2.27	11.0	93.8	2.86	24.5	1.46	8.09
80х80х6	7.34	9.35	80	6th	10	2.17	5.66	3.07	55.8	2.44	9.57	88.5	3.08	23.1	1.57	7.55
80х80х8	9.63	12.3	80	8	10	2.26	5.66	3.19	72.2	2.43	12.6	115	3.06	29.9	1.56	9.37
80х80х10	11.9	15.1	80	10	10	2.34	5.66	3.30	87.5	2.41	15.4	139	3.03	36.4	1.55	11.0
90x90x7	9.61	12.2	90	7th	eleven	2.45	6.36	3.47	92.5	2.75	14.1	147	3.46	38.3	1.77	11.0
90x90x8	10.9	13.9	90	8	eleven	2.50	6.36	3.53	104	2.74	16.1	166	3.45	43.1	1.76	12.2
90x90x9	12.2	15.5	90	9	eleven	2.54	6.36	3.59	116	2.73	17.9	184	3.44	47.9	1.76	13.3
90х90х10	15.0	17.1	90	10	eleven	2.58	6.36	3.65	127	2.72	19.8	201	3.42	52.6	1.75	14.4
100x100x8	12.2	15.5	100	8	12	2.74	7.07	3.87	145	3.06	19.9	230	3.85	59.9	1.96	15.5
100x100x10	15.0	19.2	100	10	12	2.82	7.07	3.99	177	3.04	24.6	280	3.83	73.0	1.95	18.3
100x100x12	17.8	22.7	100	12	12	2.90	7.07	4.11	207	3.02	29.1	328	3.80	85.7	1.94	20.9
120x120x8	14.7	18.7	120	8	13	3.23	8.49	4.56	255	3.69	29.1	405	4.65	105	2.37	23.1
120х120х10	18.2	23.2	120	10	13	3.31	8.49	4.69	313	3.67	36.0	497	4.63	129	2.36	27.5
120х120х12	21.6	27.5	120	12	13	3.40	8.49	4.80	368	3.65	42.7	584	4.60	152	2.35	31.6
125x125x8	15.3	19.5	125	8	13	3.35	8.84	4.74	290	3.85	31.7	461	4.85	120	2.47	25.3
125x125x10	19.0	24.2	125	10	13	3.44	8.84	4.86	356	3.84	39.3	565	4.83	146	2.46	30.1
125x125x12	22.6	28.7	125	12	13	3.52	8.84	4.98	418	3.81	46.6	664	4.81	172	2.45	34.6
150х150х10	23.0	29.3	150	10	16	4.03	10.6	5.71	624	4.62	56.9	990	5.82	258	2.97	45.1
150х150х12	27.3	34.8	150	12	16	4.12	10.6	5.83	737	4.60	67.7	1170	5.80	303	2.95	52.0
150х150х15	33.8	43.0	150	15	16	4.25	10.6	6.01	898	4.57	83.5	1430	5.76	370	2.93	61.6
180х180х15	40.9	52.1	180	15	18	4.98	12.7	7.05	1590	5.52	122	2520	6.96	653	3.54	92.7
180х180х18	48.6	61.9	180	18	18	5.10	12.7	7.22	1870	5.49	145	2960	6.92	768	3.52	106
200x200x16	48.5	61.8	200	16	18	5.52	14.1	7.81	2340	6.16	162	3720	7.76	960	3.94	123
200х200х20	59.9	76.3	200	20	18	5.68	14.1	8.04	2850	6.11	199	4530	7.70	1170	3.92