GOST 8320.6-83

GOST 27772-2015 GOST P 52927-2015 GOST P 56354-2015 GOST P 56355-2015 GOST 30245-2012 GOST 32603-2012 GOST 24045-2016 GOST 8509-93 GOST 8283-93 GOST 8240-97 GOST 5257-98 GOST 30245-2003 GOST 24045-94 GOST 19772-93 GOST 19771-93 GOST 14635-93 GOST 8319.4-75 GOST 8319.13-75 GOST 8320.6-83 GOST 8320.2-83 GOST 8320.3-83 GOST 5267.8-90 GOST 5267.1-90 GOST 12492.4-90 GOST 12492.1-90 GOST 30565-98 GOST 5422-73 GOST 7511-73 GOST 9234-74 GOST 19425-74 GOST 8319.8-75 GOST 8319.5-75 GOST 8319.0-75 GOST 21026-75 GOST 8319.6-75 GOST 11474-76 GOST 13229-78 GOST 8281-80 GOST 8278-83 GOST 8320.10-83 GOST 8282-83 GOST 8320.9-83 GOST 8320.13-83 GOST 12492.15-90 GOST 5267.6-90 GOST 5267.0-90 GOST 5267.11-90 GOST 8319.12-75 GOST 10551-75 GOST 8319.11-75 GOST 25577-83 GOST 8320.4-83 GOST 8320.12-83 GOST 8320.0-83 GOST 5157-83 GOST 8320.5-83 GOST 26020-83 GOST 8320.11-83 GOST 4781-85 GOST 5267.2-90 GOST 12492.7-90 GOST 5267.9-90 GOST 12492.0-90 GOST 12492.10-90 GOST 12492.12-90 GOST 5267.12-90 GOST 8319.2-75 GOST 8320.7-83 GOST 8320.8-83 GOST 18662-83 GOST 8320.1-83 GOST 8510-86 GOST 8239-89 GOST 17152-89 GOST 12492.6-90 GOST 5267.10-90 GOST 12492.2-90 GOST 5267.4-90 GOST 5267.13-90 GOST 12492.5-90 GOST 12492.3-90 GOST 12492.8-90 GOST 5267.3-90 GOST 12492.14-90 GOST 12492.9-90 GOST 5267.7-90 GOST 12492.11-90 GOST 12492.13-90 GOST 5267.5-90

gost-83206-83.pdf (31.58 KiB)
ГОСТ 8320.6-83

GOST 8320.6−83 periodic sections produced by cross-helical rolling for gear shaft. Assortment

GOST 8320.6−83
Group B22

INTERSTATE STANDARD
PERIODIC SECTIONS PRODUCED BY CROSS-HELICAL ROLLING
FOR GEAR SHAFT
Assortment

Periodic sections produced by cross-helical rolling for gear shaft. Dimensions

OKP 09 4400

Date of introduction 1985−01−01

The decision of the State Committee USSR on standards on 20 April 1983 1975 N. date of entry installed 01.01.85

Limitation of actions taken by Protocol No. 7−95 Interstate Council for standardization, Metrology and certification (ICS 11−12−95)
INSTEAD, GOST 8320.6−73
REISSUE

1. This standard applies to hot round periodic profiles for the pinion shaft, manufactured helical rolling.

2. The dimensions of the profiles and limit deviations thereon shall be as specified in the drawing and in the table.

ГОСТ 8320.6-83 Профили периодические поперечно-винтовой прокатки для вала-шестерни. Сортамент

Dimensions, mm

But- measures about — Phil															— Start cutting	The number of periods	The mass of one of the period, kg
But- min.	Pred. off.	But- min.	Pred. off.	But- min.	But- min.	But- min.	Pred. off.	But- min.	Pred. off.	But- min.	Pred. off.	But- min.	Pred. off.
1	145	±5	341	±5	333	2038	140	+15	48	+15	95	+1,0 -1,5	130	+1,0 -1,5	8	6	27,8
2	2379	120	7	24,8