GOST 1173-93

• gost-1173-93.pdf (453.45 KiB)
  ГОСТ 1173-93

INTER-STATENY COUNCIL FOR STANDARDIZATION, METROLOGY AND CERTIFICATION

(MGS)

INTERSTATE COUNCIL FOR STANDARDIZATION, METROLOGY AND CERTIFICATION
(ISC)

INTERSTATE STANDARD

GOST 1173−2006

FOUL, IGA, RIBBON, SHEET AND PLATE COPPER

TECHNICAL CONDITIONS

Moscow WithSTANDARTINFORM 2007

PPredislovie

Goals, basic principles and main procedure of works on interstate standardization have been established in GOST 1.0−92 «interstate standardization system. Basic provisions» and GOST 1.2−97"interstate standardization system. Interstate standards, rules and recommendations on interstate standardization. The procedure of development, adoption, application, renewal and cancellation"

Withreference to the standard

1 DEVELOPED by the Technical Committee for standardization TC 106 «Tsvetmetprokat», Scientific-research, project and design Institute for alloys and processing of nonferrous metals «joint-stock company «Institute tsvetmetobrabotka» (JSC «Institute tsvetmetobrabotka»)

2 SUBMITTED by the Technical Secretariat of the Interstate Council for standardization, Metrology and certification

3 ACCEPTED by the Interstate Council for standardization, Metrology and certification (Protocol № 29 from June 24, 2006)

The standard was accepted by voting:

Short name of the country on MK (ISO 3166) 004−97	Country code by MK (ISO 3166) 004−97	Abbreviated name of the national authority standardization
Azerbaijan	AZ	Azstandart
Belarus	BY	Gosstandart Of The Republic Of Belarus
Kazakhstan	KZ	Gosstandart Of The Republic Of Kazakhstan
Kyrgyzstan	KG	Kyrgyzstandard
Moldova	MD	Moldova-Standard
Russian Federation	EN	Federal Agency on technical regulation and Metrology
Tajikistan	TJ	Tajikstandart
Uzbekistan	UZ	Uzstandard
Ukraine	UA	Derzhspozhyvstandart Of Ukraine

(Amendment).

4 by Order of the Federal Agency for technical regulation and Metrology dated December 27, 2006 No. 496-St inter-state standard GOST 1173−2006 introduced as a national standard of the Russian Federation from January 1, 2008

5 REPLACE GOST 1173−93 and GOST 495−92

Andinformation about introduction in action (termination) of this standard is published in the index «National standards».

Andinformation about the changes to this standard is published in the index «National standards», and the text changes — in the information sign «National standards». In case of revision or cancellation of this standard the appropriate information will be published in the information index «National standards»

The CONTENTS

1 Scope 2 Normative references 3 Terms and definitions 4 Assortment 5 Technical requirements 6 acceptance Rules 7 Methods of inspection and testing 8 Marking, packaging, transportation and storage Appendix a Theoretical mass of 1 m2 of the copper foil, tapes and sheets Appendix B Compliance designations copper grades according to GOST 1173−2006 and EN 1652:1998 App In hardness Values

INTERSTATETION STANDARD

FOUL, IGA, RIBBON, SHEET AND PLATE COPPER

Technical conditions

Copper foil, ribbons, sheets and plates. Specifications

DATA introduction — 2008−01−01

1 Scope

This standard applies to cold-rolled copper foil and strip, cold-rolled and hot-rolled sheets and plates of General purpose.

The standard does not apply to the copper tape designed for radiators.

2 Normative references

This standard uses the regulatory references to the following international standards:

GOST 166−89 (ISO 3599−76) Calipers. Specifications

GOST 427−75 Rulers measuring metal. Specifications

GOST 859−2001 Copper. Brand

GOST 1497−84 (ISO 6892−84) Metals. Test methods tensile

GOST 2991−85 wooden disposable Boxes for loads up to 500 kg. General specifications

The Wire GOST 3282−74 General purpose low carbon steel. Specifications

GOST 3560−73 package steel Strip. Specifications

GOST 4381−87 Micrometers lever. General specifications

GOST 6507−90 Micrometers. Specifications

GOST 7229−76 Cables, wires and cords. Method of determination of electrical resistance of conductors and conductors

GOST 7376−89 corrugated Cardboard. General specifications

GOST 7502−98 metallic measuring tape. Specifications

GOST 7933−89 Cardboard for consumer packaging. General specifications

GOST 8273−75 wrapping Paper. Specifications

GOST 9078−84 flat Pallets. General specifications

GOST 9557−87 flat wooden Pallet size 8001200 mm. specifications

GOST 9696−82 multi-turn Indicators with a scale division of 0.001 and 0.002 mm. specifications

GOST 9717.1−82 Copper. Method of spectral analysis on a metal standard samples with photoelectric registration of spectrum

GOST 9717.2−82 Copper. Method of spectral analysis on a metal standard samples with photographic registration of spectrum

GOST 9717.3−82 Copper. Method of spectral analysis of oxide standard specimens

GOST 10198−91 wooden Boxes for goods of mass over 200 up to 20000 kg. General specifications

GOST 10510−80 (ISO 8490−86) Metals. Test method for the extrusion of sheets and strips for Eriksen

GOST 11701−84 Metals. Methods tensile tests of thin sheets and strips

GOST 13938.1−78 Copper. Methods for determination of copper

GOST 13938.2−78 Copper. Methods of determining sulphur

GOST 13938.3−78 Copper. Method of determination of phosphorus

GOST 13938.4−78 Copper. Methods of iron determination

GOST 13938.5−78 Copper. Methods for determination of zinc

GOST 13938.6−78 Copper. Methods for determination of Nickel

GOST 13938.7−78 Copper. Methods for determination of lead

GOST 13938.8−78 Copper. Methods for determination of tin

GOST 13938.9−78 Copper. Methods for determination of silver

GOST 13938.10−78 Copper. Methods for determination of antimony

GOST 13938.11−78 Copper. Method for the determination of arsenic

GOST 13938.12−78 Copper. Methods for determination of bismuth

GOST 13938.13−93 Copper. Methods for determination of oxygen

GOST 13938.15−88 Copper. Methods for determination of chromium and cadmium

GOST 14019−2003 (ISO 7438:1985) Materials of metal. Method of bend test

GOST 14192−96 Marking of cargo

GOST 15102−75 the universal metal closed Container of nominal gross mass 5,0 t Technical specifications

GOST 15467−79 quality Control of products. Basic concepts. Terms and definitions

GOST 15846−2002 Products that are sent to the far North regions and equated areas. Packing, marking, transportation and storage

GOST 18242−72* Statistical acceptance inspection by alternative feature. Plans control

* On the territory of the Russian Federation GOST R 50779.71−99 (ISO 2859−1-89)** Statistical methods. Procedure sampling on alternative grounds. Part 1. Sampling plans consistent parties on the basis of acceptable quality level AQL.

__________

** Cm. note the FSUE «STANDARTINFORM»

GOST 18321−73 Statistical quality control. Methods of random selection of piece products

GOST 18477−79 Containers are universal. The types, basic parameters and dimensions

GOST 20435−75 the universal metal closed Container of nominal gross mass 3,0 t specifications

GOST 21073.1−75 ferrous Metals. Determination of grain size by comparison with the scale of microstructures

GOST 21140−88 Tara. System sizes

GOST 21650−76 means of fastening of package cargoes in transport packages. General requirements

GOST 22225−76 universal Containers with a gross weight 0,625 and 1,25 t. specifications

GOST 22322−77 Lining for packing goods in wooden packaging. General specifications

GOST 24047−80 Semi-finished products from nonferrous metals and their alloys. Sampling for tensile test

GOST 24231−80 non-ferrous metals and alloys. General requirements to selection and preparation of samples for chemical analysis

GOST 26663−85 transport Packs. Formation with the use of packaging. General technical requirements

GOST 26877−91 metal Products. Methods of measuring form deviations of

Note — When using this standard appropriate to test the effect of reference standards for the sign «National standards» drawn up as of January 1 of the current year and related information signs, published in the current year. If the reference document is replaced (modified), then the use of this standard should be guided by the replaced (modified) document. If the reference document is cancelled without replacement, then the situation in which the given link applies to the extent that does not affect this link.

3 Terms and definitions

This standard applies the following terms with the corresponding definitions.

3.1 foil: Flat rolled product of rectangular cross section of uniform thickness from 0.05 to 0.10 mm, supplied in coil.

3.2 tape: Flat rolled product of rectangular cross section of uniform thickness from 0.10 to 6.00 mm inclusively, supplied in rolls or cut to length (strip) with a cut edge.

3.3 sheet: Flat rolled product of rectangular cross section of uniform thickness: cold rolled — from 0.20 to 12.00 mm inclusively, supplied in segments with cut or rolled edge; hot — from 3.00 to 25.00 mm inclusively, supplied in segments.

3.4 plate: Flat rolled product of rectangular cross section of uniform thickness over 25,00 mm, supplied in segments.

3.5 camber: the Deviation from straightness, in which the surface of the side edge of the foil, ribbon or sheet in a horizontal plane has the shape of an arc.

3.6 deflection (warpage): Private view of the deviations from flatness in longitudinal or transverse direction, wherein the surface of the tape, sheet or plate has an arc shape.

3.7 cut end Squareness, mm: Failure to form, in which the cutting plane forms with the longitudinal plane of the sheet or plate angle less than or greater than 90°.

4 Assortment

4.1 the Thickness of the foil, tapes, cold rolled sheets and tolerances for thickness depending on width shall be as specified in table 1.

Table 1

In millimeters

Nominal thickness	Maximum deviation in thickness with a width
	from 10 to 300 incl.		over 300 to 600 incl.		St. 600 to 800 incl.	St. 800 to 1000 incl.
	norms. accurate.	povysh. accurate.	norms. accurate.	povysh. accurate.
From 0.05 to 0.10	0	-	-	-	-	-
	— 0,01
From 0.10 to 0.14 incl.	0	-	0	-	-	-
	— 0,02		— 0,04
SV. 0.14 to 0.22 incl.	0	0	0	-	-	-
	— 0,03	— 0,02	— 0,04
SV. 0,22−0,35 incl.	0	0	0	-	-	-
	— 0,04	— 0,03	— 0,05
SV. 0.35 to 0.50 incl.	0	0	0	0	0	0
	— 0,05	— 0,04	— 0,06	— 0,05	— 0,09	— 0,12
SV. Of 0.50 to 0.70 incl.	0	0	0	0	0	0
	— 0,06	— 0,05	— 0,08	— 0,07	— 0,10	— 0,15
SV. Of 0.70 to 0.90 incl.	0	0	0	0	0	0
	— 0,07	— 0,06	— 0,09	— 0,08	— 0,12	— 0,17
SV. Of 0.90 to 1.10 incl.	0	0	0	0	0	0
	— 0,08	— 0,06	— 0,10	— 0,09	— 0,12	— 0,17
SV. Of 1.10 to 1.50 incl.	0	0	0	0	0	0
	— 0,09	— 0,07	— 0,12	— 0,11	— 0,14	— 0,18
SV. Of 1.50 to 1.80 incl.	0	0	0	0	0	0
	— 0,10	— 0,08	— 0,14	— 0,13	— 0,16	— 0,20
SV. Of 1.80 to 2.00 incl.	0	0	0	0	0	0
	— 0,11	— 0,09	— 0,15	— 0,14	— 0,18	— 0,22
SV. Of 2.00 to 2.20 incl.	0	-	0	-	0	0
	— 0,12		— 0,16		— 0,18	— 0,22
SV. 2.20 to 3.00 cyl.	0	-	0	-	0	0
	— 0,14		— 0,18		— 0,20	— 0,24
SV. Of 3.00 to 3.50 incl.	0	-	0	-	0	0
	— 0,14		— 0,20		— 0,24	— 0,28
SV. Of 3.50 to 4.00 incl.	0	-	0	-	0	0
	— 0,18		— 0,22		— 0,24	— 0,30
SV. Of 4.00 to 4.50 incl.	0	-	0	-	0	0
	— 0,18		— 0,24		— 0,27	— 0,32
SV. Of 4.50 to 6.50 incl.	0	-	0	-	0	0
	— 0,22		— 0,26		— 0,30	— 0,34
SV. Of 6.50 to 7.00 incl.	-	-	0	-	0	0
			— 0,28		— 0,34	— 0,36
SV. Of 7.00 to 8.00 incl.	-	-	0	-	0	0
			— 0,30		— 0,36	— 0,44
SV. Of 8.00 to 9.00 incl.	-	-	0	-	0	0
			— 0,32		— 0,40	— 0,50
SV. 9,00−10,00 incl.	-	-	0	-	0	Zero
			— 0,34		— 0,40	— 0,50
SV. 10,00 to 11.00 incl.	-	-	0	-	0	0
			— 0,40		— 0,50	To 0.60
SV. Of 11.00 to 12.00 incl.	-	-	0	-	0	0
			— 0,44		— 0,50	— 0,70
Note the Theoretical weight of 1 m2 of foil, tapes and sheets for thicknesses that are used currently are given in Appendix A.

4.2 By agreement between the consumer and the manufacturer of the tape and cold-rolled sheets are produced with a symmetrical limit deviations for thickness listed in table 2.

Table 2

In millimeters

Nominal thickness	Maximum deviation in thickness with a width
	350 incl.	St. 350 to 700 incl.	over 700 up to 1000 incl.
From 0.10 to 0.20 incl.	± 0,018	-	-
SV. 0.20 to 0.30 incl.	± 0,022	± 0,03	± 0,04
SV. 0.30 to 0.40 incl.	± 0,025	± 0,04	± 0,05
SV. 0.40−0.50 incl.	± 0,030	± 0,05	± 0,06
SV. Of 0.50 to 0.80 incl.	± 0,040	± 0,06	± 0,07
SV. 0.80 to 1.20 incl.	± 0,050	± 0,07	± 0,09
SV. Of 1.20 to 1.80 incl.	± 0,060	± 0,08	± 0,10
SV. Of 1.80 to 2.50 incl.	± 0,070	± 0,09	± 0,11
SV. Of 2.50 to 3.20 incl.	± 0,080	± 0,10	± 0,13
SV. Of 3.20 to 4.00 incl.	± 0,10	± 0,12	± 0,15
SV. Of 4.00 to 5.00 incl.	± 0,12	± 0,14	± 0,17
SV. Of 5.00 to 6.00 incl.	± 0,14	± 0,16	± 0,20
SV. Of 6.00 to 7.00 incl.	± 0,16	± 0,19	± 0,23
SV. Of 7.00 to 8.00 incl.	± 0,18	± 0,22	± 0,26
SV. Of 8.00 to 9.00 incl.	± 0,20	± 0,25	± 0,29
SV. 9,00−10,00 incl.	± 0,22	± 0,28	± 0,32

4.3 the Width of the foil and ribbons and limit deviations on width depending on thickness shall be as specified in table 3.

Table 3

In millimeters

Nominal thickness	Limit deviation width when the width of the
	up to 100 incl.		over 100 to 170 incl.		St. 170 to 300 incl.		over 300 to 600 incl.		St. 600 to 800 incl.		St. 800 to 1000 incl.
	norms. accurate.	povysh. accurate.	norms. accurate.	povysh. accurate.	norms. accurate.	povysh. accurate.	norms. accurate.	povysh. accurate.	norms. accurate.	povysh. accurate.	norms. accurate.	povysh. accurate.
From 0.05 to 0.10	0	0	0	0	0	0	-	-	-	-	-	-
	— 0,5	— 0,3	— 0,5	— 0,4	— 0,8	— 0,7
From 0.10 to 1.00 incl.	0	0	0	0	0	0	0	0	0	0	0	0
	— 0,5	— 0,3	— 0,5	— 0,4	— 0,8	— 0,7	— 1,2	— 1,0	— 2,0	— 1,8	To 2.6	And 2.3
SV. 1.00 to 2.00 incl.	0	0	0	0	0	0	0	0	0	0	0	0
	— 0,8	— 0,4	— 0,8	— 0,6	To 1.3	— 1,0	— 1,6	— 1,2	A 2.8	To 2.6	— 3,5	— 3,2
SV. Of 2.00 to 3.00 incl.	0	Zero	0	0	0	0	0	0	-	-	-	-
	— 2,0	— 1,2	And 3.0	— 1,6	And 3.0	— 2,0	And 3.0	— 2,0
SV. Of 3.00 to 6.00 incl.	0	0	0	0	0	0	0	0	-	-	-	-
	And 3.0	Is 2.5	— 3,5	And 3.0	— 3,5	And 3.0	To 4.0	— 3,5
Note — tape of a width more than 600 mm are made with a thickness of 0.50 mm or more.

4.4 By agreement between the consumer and the manufacturer of the tape are made with plus limit deviations on width, given in table 4.

Table 4

In millimeters

Nominal thickness	Limit deviation width when the width of the
	to 50 incl.	over 50 to 100 incl.	over 100 to 200 incl.	over 200 to 350 cyl.	over 350 to 500 incl.	over 500 to 700 incl.	over 700 to 1250 incl.
From 0.10 to 1.00 incl.	+ 0,20	+ 0,30	+ 0,40	+ 0,60	+ 1,0	+ 1,5	+ 2,0
	0	0	0	0	0	0	0
SV. 1.00 to 2.00 incl.	+ 0,30	+ 0,40	+ 0,50	+ 1,0	+ 1,2	+ 1,5	+ 2,0
	0	0	0	0	0	0	0
SV. 2.00 to 2.50 incl.	+ 0,50	+ 0,60	+ 0,70	+ 1,2	+ 1,5	+ 2,0	+ 2,5
	0	0	0	0	0	0	0
SV. Of 2.50 to 3.00 cyl.	+ 1,0	+ 1,10	+ 1,20	+ 1,5	+ 2,0	+ 2,5	3.0 a
	0	0	0	0	0	0	0
SV. Of 3.00 to 4.00 incl.	+ 2,0	+ 2,30	+ 2,50	3.0 a	+ 4,0	+ 5,0	+ 6,0
	0	0	0	0	0	0	0

4.5 Width of cold rolled sheets and tolerances for the width depending on thickness shall be as specified in table 5.

Table 5

In millimeters

Nominal thickness	Limit deviation width when the width of the
	up to 300 incl.		SV. 300 to 1000 incl.
	norms. accurate.	povysh. accurate.	norms. accurate.	povysh. accurate.
From 0.20 to 2.00 incl.	0	0	0	0
	And 3.0	— 2,0	— 6,0	To 4.0
SV. Of 2.00 to 6.00 incl.	0	0	0	0
	To 5.0	To 4.0	To 8.0	— 6,0
SV. Of 6.00 to 12.00 incl.	0	0	0	0
	— 10,0	To 8.0	— 10,0	To 8.0

4.6 Upon request of the consumer and the manufacturer of cold rolled sheets are produced with plus limit deviations on width, specified in table 6.

Table 6

In millimeters

Nominal thickness	Limit deviation width when the width of the
	350 incl.	over 350 to 1000 incl.
To 2.00 incl.	+ 2,0	+ 6,0
	0	0
SV. 2.00−5.00 incl.	+ 4,0	+ 8,0
	0	0
SV. 5,00	+ 8,0	+ 10,0
	0	0

4.7 Length foil and strip shall be as defined in table 7.

Table 7

The thickness of the foil and tape, mm	Length foil and strip, m, not less
From 0.05 to 0.10	30
From 0.10 to 0.50 incl.	30
SV. 0.50 to 1.00 incl.	20
SV. 1.00 to 2.00 incl.	10
SV. Of 2.00 to 6.00 incl.	2
Note — Allow foil and strip thickness to 2.00, inclusive of a lesser length but not less than 5 m, not more than 10% of the batch weight.

4.8 Tape, cut to length and cold-rolled sheets are produced in length from 500 to 2000 mm with maximum deviation in length:

— thickness up to 3,00 mm incl. minus 10.0 mm;

— of a thickness of 3.00 mm St — minus 20.0 mm.

4.9 the user agreement with the manufacturer of the tape, cut to length and cold-rolled sheets are produced with plus extreme deviations in length:

— thickness up to 3,00 mm incl. — plus 10.0 mm;

— of a thickness of 3.00 mm St — plus is 15.0 mm.

4.10 Thickness of hot-rolled sheets and tolerances for thickness depending on width shall be as specified in table 8.

Table 8

In millimeters

Nominal thickness	Maximum deviation in thickness with a width
	from 100 to 1200 incl.	over 1200 to 1500 incl.	St 1500 to 1800 cyl.	St. 1800 to 2500 incl.	St. 2500 to 3000 incl.
From 3.00 to 3.50 incl.	0	0	0	-	-
	— 0,40	To 0.60	To 0.60
SV. 3.50 to 6.00 incl.	0	0	0	0	-
	— 0,45	— 0,70	— 0,70	— 0,90
SV. Of 6.00 to 7.00 incl.	0	0	0	0	-
	— 0,50	— 0,70	— 0,70	— 0,90
SV. Of 7.00 to 8.00 incl.	0	0	0	0	0
	— 0,50	— 0,80	— 0,80	— 1,00	— 1,20
SV. Of 8.00 to 9.00 incl.	0	0	0	0	0
	— 0,55	— 0,80	— 0,80	— 1,00	— 1,20
SV. 9,00−10,00 incl.	0	0	0	0	0
	— 0,55	— 0,90	— 0,90	— 1,00	— 1,20
SV. 10,00 to 11.00 incl.	0	0	0	Zero	0
	— 0,70	— 0,90	— 0,90	— 1,00	— 1,20
SV. Of 11.00 to 12.00 incl.	0	0	0	0	0
	— 0,80	— 1,00	— 1,00	— 1,10	— 1,20
SV. Of 12.00 to 13.00 incl.	0	0	0	0	0
	— 0,90	— 1,00	— 1,00	— 1,20	— 1,40
SV. Of 13.00 to 14.00 incl.	0	0	0	0	0
	— 0,90	— 1,10	— 1,10	— 1,30	— 1,50
SV. Of 14.00 to 15.00 incl.	0	0	0	0	0
	— 1,00	— 1,20	— 1,20	— 1,40	— 1,60
SV. Of 15.00 to 16.00 incl.	0	0	0	0	0
	— 1,00	— 1,30	— 1,30	— 1,50	— 1,60
SV. Of 16.00 to 17.00 incl.	0	0	0	0	0
	— 1,20	— 1,40	— 1,40	— 1,50	— 1,60
SV. 17.00 and 19.00 incl.	0	0	0	0	0
	— 1,20	— 1,40	— 1,50	— 1,60	— 1,80
SV. Of 19.00 to 22.00 incl.	0	0	0	0	0
	— 1,40	— 1,60	— 1,60	— 1,80	— 2,00
SV. Of 22.00 to 25.00 incl.	0	0	0	0	-
	— 1,60	— 1,80	— 1,80	— 1,80

4.11 the Thickness of slabs and limit deviations on thickness depending on width shall be as specified in table 9.

Table 9

In millimeters

Nominal thickness	Maximum deviation in thickness with a width
	from 150 to 1000 incl.	St. 1000 to 2000 incl.	St 2000 to 2500 incl.
From 25.00 to 40.00 incl.	0	0	0
	— 2,0	Is 2.5	And 3.0
SV. Of 40.00 to 60.00 incl.	0	0	0
	A 2.8	And 3.0	To 4.0
SV. 60,00 to 100,00 incl.	0	0	-
	And 3.0	To 4.0
SV. The 100.00 to 150.00 incl.	0	0	-
	To 3.6	To 5.0

4.12 agreement between the consumer and the manufacturer plates and hot rolled sheets are produced with a symmetrical limit deviations on thickness specified in table 10.

Table 10

In millimeters

Nominal thickness	Maximum deviation in thickness with a width
	up to 700 incl.	over 700 up to 1000 incl.	St 1000 to 1500 incl.	St 1500
From 3.00 to 5.00 incl.	± 0,25	± 0,30	± 0,35	By appointment
SV. Of 5.00 to 7.50 incl.	± 0,35	± 0,40	± 0,45
SV. Of 7.50 to 10.00 incl.	± 0,45	± 0,50	± 0,55
SV. 10.00 to 15.00 incl.	± 0,75	± 0,80	± 0,90
SV. Of 15.00 to 25.00 incl.	± 0,95	± 1,05	± 1,30
SV. Of 25.00 to 50.00 incl.	± 1,30	± 1,40	± 1,50
SV. 50,00	± 1,50	± 1,65	± 1,80

4.13 hot Rolled sheets are produced with thickness of 100 to 3000 mm. maximum deviations in width:

— with a width from 100 to 600 mm incl. or minus 10 mm;

— at width more than 600 mm minus 20 mm.

4.14 hot-Rolled sheets are produced with a length from 1000 to 6000 mm. tolerances for length minus 30 mm.

By agreement between the consumer and the manufacturer of hot rolled sheets can be manufactured with a length other than shown.

4.15 Plates are made in widths from 150 to 2500 mm and length from 600 to 4000 mm. tolerances for width and length should be no more than plus 40,0 mm.

Legend foil, ribbons, sheets and plates placed according to the scheme:

Use the following abbreviations:

method of production: cold rolled steel — D,

HR — G;

sectional shape: rectangular — OL;

accuracy of manufacturing: normal thickness and width — N,

normal thickness and increased in width,

increased thickness and a normal width And

increased in thickness and width — P;

condition: soft — M

semi — P,

solid — T;

length: random — ND;

special conditions: increased length — UD,

for power capacitors and transformer windings — TO

the normalized depth of the extrusion — GW,

extreme deviations:

the thickness of the «±" and width «+" — EN,

the thickness of the «±" and width «-" — ER.

Instead of the missing data is «X», in addition to the designation lengths.

Examples of symbols:

Cold-rolled steel strip, rectangular, high accuracy on thickness and width, semi-hard, thickness 0,70 mm, width 35 mm, random length, made of copper marks M1:

Lcient DPRP ON, 7035 НДМ1 GOST 1173−2006

Cold-rolled steel strip, rectangular, normal accuracy in thickness and width, soft, thickness 0.25 mm, width 100 mm, random length, made of copper marks M1, with a normalized depth of the extrusion:

Lcient DPMM 0,25100 ND M1 GW GOST 1173−2006

Tape, cut to length, cold-rolled, rectangular, high accuracy on thickness and width, solid, with a thickness of 1.20 mm, width 80 mm, length 2000 mm, made of copper brand M2:

Lcient DPCT 1,20802000 M2 GOST 1173−2006

Cold-rolled steel strip, rectangular, solid, thickness 2.0 mm, width 500 mm, random length, made of copper marks M1, extreme deviations in thickness «±" and width «+":

Lcient DPRT 2,0500 НДМ1 EN GOST 1173−2006

Steel cold-rolled sheet, rectangular, high accuracy in thickness and normal accuracy in width, solid, with a thickness of 1.00 mm, width 200 mm, length 2000 mm, made of copper brand M2:

List CPRIT 1,002002000 M2 GOST 1173−2006

Steel hot-rolled sheet, rectangular, thickness 7.0 mm, width 1500 mm, length 3000 mm, of copper grade M2:

List GPRH 7,015003000 M2 GOST 1173−2006

5 Technical requirements

5.1 Foil, ribbons, sheets and plates manufactured in accordance with the requirements of this standard, made of copper grades M1, M1r, M1 °F, M2, M2r, M3, M3r GOST 859 with the chemical composition shown in table 11.

Allowed for the production of copper the brands M1r, M2r, M3r to use copper obtained by fire refining.

At the request of the consumer tape is designed for power capacitors and transformer windings, can be made of copper M1E brand with specific volumetric electric resistance of not more than 17,4810^-9 OMM (0,01748 Ohms²/m).

Table 11

Percentage

Marking stamps	Mass fraction of element												A method of producing
	Copper + silver, no less	Impurity, not more than
		Bismuth	Iron	Nickel	Zinc	Tin	Antimony	Arsenic	Lead	Sulfur	Oxygen	Phosphorus
M1	99,90	0,001	0,005	0,002	0,004	0,002	0,002	0,002	0,005	0,004	0,05	-	The re-melting of cathodes
M1r	99,90	0,001	0,005	0,002	0,005	0,002	0,002	0,002	0,005	0,005	0,01	0,002 — 0,012	The re-melting of cathodes and scrap copper deoxidation with phosphorus
M1F	99,90	0,001	0,005	0,002	0,005	0,002	0,002	0,002	0,005	0,005	-	0,012 — 0,04
M2r	99,70	0,002	0,05	0,2	-	0,05	0,005	0,01	0,01	0,01	0,01	0,005 — 0,06
M3r	A 99.50	0,003	0,05	0,2	-	0,05	0,05	0,05	0,03	0,01	0,01	0,005 — 0,06
M2	99,70	0,002	0,05	0,2	-	0,05	0,005	0,01	0,01	0,01	0,07	-	Fire refining and melting of waste and scrap of copper
M3	A 99.50	0,003	0,05	0,2	-	0,05	0,05	0,01	0,05	0,01	0,08
Notes 1 In the marking of copper grades M1 and M1r designed for the electrical industry and to be tested for conductivity, additionally include the letter Y. 2 Compliance notation copper grades according to this standard and EN 1652 is given in Appendix B.

5.2 Foil and strip manufactures cold-rolled sheet and plate cold — rolled and hot-rolled. Strip, cold-rolled sheets and plates are made in a soft, semi-solid and solid States.

Foil is manufactured in a solid state.

Cold-rolled sheets with a thickness of 0.20 mm and 0.30 mm are made in the solid state.

5.3 the surface of the foil, ribbons, sheets and plates should be free from contamination, hinder the inspection.

On the surface allowed the color of a tint, a local darkening, traces of the technological lubricant, as well as local defects, not bringing the foil tape and cold rolled sheets at reference sweep for tolerances for thickness.

On the surface of the plates and hot rolled sheets allowed roughness and prints from the rolls in the form of fine mesh. Traces of slag rejection symptom are not.

Plates and hot rolled sheets are produced without etching of the surface. By agreement between the consumer and the manufacturer is allowed to produce slabs and hot rolled sheets with etched surface and the plate by machining the surface (milled).

On the surface of the plates and hot rolled sheets allowed individual defects, not displaying plates and hot rolled sheets at reference sweep for tolerances for thickness.

Permitted surface quality control samples are agreed between manufacturer and user.

5.4 Foil, tapes and sheets up to 6.00 mm should be trimmed evenly and should not have a significant Burr on GOST 15467. Wrinkled and ragged edge is not allowed. Only small undulations, disappearing with a control curve.

The tape thickness of 2.00 mm, is designed for power capacitors and windings of the transformer must not have burrs.

Allowed to produce strips and sheets without trimming.

5.5 Plate needs to be trimmed for width and length. Allowed on the customer’s plate manufacturing without cropping, spaced on nominal sizes.

5.6 Allowable cut end Squareness, mm should take leaves, ribbon, cut into lengths, and the plates for the limit deviations on width and length.

5.7 Camber strips shall not exceed 3 mm per 1 m length.

Camber sheets and tapes cut to length with thickness up to 4.0 mm should not exceed 5 mm per 1 m of length, thickness exceeding 4,0 mm — 8 mm per 1 m length.

5.8 Deflection of strips of p should not exceed 1 mm for belt widths from 10 mm to 100 mm For belt widths over 100 mm deflection N mm, calculated by the formula

(1)

where P is a deflection for tapes up to a width of 100 mm, mm.

b — belt width, mm.

The deflection of cold-rolled sheets and strips, cut to length, should not exceed 1 mm per 100 mm width and 20 mm per 1 m length of the sheet or tape cut to length.

For hot rolled sheets and plates of deflection is determined by agreement between the consumer and the manufacturer.

5.9 According to the customer’s requirement cold-rolled soft sheets, strip, cut to length, and hot-rolled sheets with a thickness up to 12.0 mm shall withstand a bend test in cold state around a mandrel of diameter equal to the thickness of the sheet or ribbon, cut into lengths, without the appearance of cracks and delamination.

Bending test of strips, cut to length, and thickness up to 5 mm inclusive shall be carried out before the contact; thickness over 5 mm to the parallel sides.

Semi-solid ribbon, cut into lengths, sheets with a thickness of 1.00 to 10.00 mm inclusive shall withstand a bend test in cold state at 90° without the appearance of traces of tears and cracks around a mandrel radius of curvature equal to the thickness of the sheet or tape cut to length.

At the demand of the consumer sheet of deoxidized copper must withstand a bending test after annealing in a hydrogen environment.

5.10 Mechanical properties of strips and sheets shall be as specified in table 12.

Table 12

A method of manufacturing	The condition of the material	Temporary resistance sin MPa (kgf/mm2)	Elongation, %, not less
			δ10	δ5
Cold-rolled	Soft	200 — 260 (20 — 27)	36	42
	Semi-solid	240 — 310 (25 — 32)	12	15
	Solid	No less than 290 (30)	3	6
HR	-	At least 200 (20)	30	-
Notes 1 the Upper limit of the strength may be higher, but not more than 20 MPa (2 kgf/mm2) while maintaining the elongation given in the table. 2 tensile strength is determined for strips and sheets with thickness of 0.3 mm or more, the elongation — to tapes and sheets with a thickness of 0.5 mm or more. 3 hardness Values are given in Appendix B.

Mechanical properties for hot rolled sheets with thickness over 12 mm is determined by the requirement of the user.

The elongation is determined in a long (δ₁₀) or short (δ₅) samples. If the consumer does not indicate what kind of elongation, it is necessary to determine the choice for the manufacturer.

5.11 Mechanical properties of the boards determined by agreement with the consumer, in this case agree on the venue and procedure for the selection of the sample and standards mechanical properties.

5.12 At the request of the consumer the depth of the extrusion to define a soft tape thickness from 0.10 to 1.50 mm, inclusive. The extrusion depth of the spherical holes shall be as defined in table 13, while the tensile strength and elongation is determined.

Table 13

In millimeters

The radius of the punch	The depth of the spherical dimples, at least, when the thickness of the tape
	from 0.10 to 0.14 incl.	St. 0,14 to 0,16 incl.	St 0.16 to 0.28 incl.	St 0.28 to 0.55 incl.	St. of 0.55 to 0.60 incl.	St. of 0.60 to 1.10 incl.	St. of 1.10 to 1.50 incl.
10	7,0	7,5	8,0	8,5	9,0	9,5	10,0
4	3,0	3,4	3,8	4,0	-	-	-
1,5	1,5	1,5	1,8	2,1	-	-	-

5.13 On agreement between the consumer and the manufacturer soft strips are made with a regulated grain size.

6 acceptance Rules

6.1 Foil, ribbons, sheets and plates take parties. The party should consist of foil, ribbons, sheets or plates of one brand of copper, one size, one state, one precision and method of manufacture and executed by one document about quality that contains:

is the trademark or name and trademark of manufacturer;

— the name of the country of manufacture;

— legal address of the manufacturer and (or) the seller;

— the symbol foil, ribbons, sheets or plates;

— test results (as required);

— the batch number;

the weight of the party.

The weight of the batch is not limited.

Allowed to issue a single document the quality of several batches of foil, ribbons, sheets or plates of one brand of copper, one size, one state, one precision and method of manufacture, shipped to the same consumer, indicating the batch number.

6.2 To control the size, appearance, camber and deflection of the foil, ribbons, sheets, plates; skew cutting of sheets, strips, cut into lengths, and panels used a single-stage normal sampling plan for the alternative characteristic in accordance with GOST 18242 with the acceptance level of defects AQL= 4%.

The selection of rolls of foil and ribbons, sheets, tapes, cut to length, and flags in the sample is carried out «blindly» (by the greatest objectivity) according to GOST 18321.

If the quantity does not exceed three rolls of foil, tapes, or three sheets, strips, cut into lengths, and flags, checked each roll of foil tape or every sheet, tape, cut to length, plate.

6.3 To control the size, appearance, camber, skew the cut and camber of the party selected rolls of foil, ribbon or sheet, tape, cut lengths plates in accordance with table 14.

Table 14

In pieces

Lot size	The sample size	Rejection number
4 — 25	3	1
26 — 90	Thirteen	2
91 — 150	20	3
151 — 280	32	4
281 — 500	50	6
501 — 1200	80	8

6.4 To measure the thickness of the foil or tape from each selected roll, the number of measurement points is determined depending on the length of the foil or tape in a roll in accordance with table 15.

Table 15

Length of foil or strip, m	The number of controlled points per roll.	Rejection number
From 5 to 12 incl.	3	1
SV. 12 «45 «	13	2
«45» 75 «	20	3
«75» 140 «	32	4
«140» 250 «	50	6
«250» 600 «	80	8
«600» 1600 «	125	11

The length of the foil or tape in a roll to select the number of measurement points in the coil is determined by the formula (2) given in 7.4.

6.5 To measure the thickness at each selected tape, cut into lengths, or the stove, or the selected sheet, the number of measurement points is determined depending on the total number of parcels with a length of 100 mm along the perimeter of the tape, cut to length, sheet or plate in accordance with table 16. If the perimeter is not a multiple of 100 mm, the end section of a length less than 100 mm is taken for one site.

Table 16

In pieces

The number of segments on the tape, cut to length, sheet or plate	The number of controlled points	Rejection number
4 — 25	3	1
26 — 90	13	2
91 — 150	20	3
151 — 280	32	4
281 — 500	50	6
501 — 1200	80	8

6.6 in the control of the thickness of the controlled roll of foil, ribbon or tape, cut to length, sheet, plate considered valid if the number of measurements that meet the requirements of tables 1, 9, less than the acceptance number specified in table 15 or 16.

Under the control of the width, length, appearance, skew cut, camber, and deflection of a party is considered usable if the number of rolls of foil, tapes or strips, cut into lengths, sheets or plates that do not meet the requirements 4.9, 4.10, 4.14, 4.15, 5.2, 5.4, 5.5, 5.6, tables 3, 5, 7, less than the acceptance number specified in table 14.

If unsatisfactory results at least one of the controlled rolls of foil, ribbon or sheet, tape, cut into lengths, the plate is carried out continuous monitoring of the entire party.

Allowed the manufacturer to control the thickness, width, length, and quality of surface carried out in the production process.

6.7 To check the chemical composition is taken two rolls of foil, tape, two ribbons, cut to length, two sheets, or two plates taken from the party.

Allowed to the manufacturer of the sampling carried out by the molten metal.

6.8 For tensile tests (strips and sheets), bending (strip, cut to length, and leaves), hood spherical dimples (tape) and determine the amount of grain (tape) from the party taken three rolls of tape, three strips, cut into lengths, three leaves from every full or partial 1,000 kg batch of strips, cold rolled sheets and strips, cut to length, and 5000 kg batch of hot-rolled sheets.

In the production of enlarged coils of strips by welding is permitted the manufacturer to tensile tests, the hood of spherical wells and determination of grain size from batch to take three rolls of each complete and incomplete 3000 kg batch.

6.9 If unsatisfactory test results of at least one of the performance indicators specified in 6.7, 6.8, thereon, a second test of the doubled sample taken from the same batch. The results of repeated testing are spreading to the entire party.

7 Methods of inspection and testing

7.1 control the size, appearance, camber, deflection and skew of the cut performed with a given probability 96% (acceptance level of defects AQL = 4%).

7.2 appearance of the foil, ribbons, sheets and plates of check inspection without the use of magnifying devices.

7.3 the Thickness of the foil, ribbons, sheets and plates of measured multi-turn indicator according to GOST 9696, micrometer according to GOST 6507 with lever or micrometer according to GOST 4381.

7.4 Measurement of the thickness of the foil and tape is carried out at a distance of not less than 10 mm from edges and not less than 100 mm from the end of the roll of foil or tape. For tapes with a width of 20 mm or less, the measurement is performed in the middle of the width of the tape.

The thickness of the foil or tape measure for each selected coil to points positioned uniformly randomly along the length of the roll.

The length of the roll L, m, calculated by the formula

(2)

where D and d are respectively the outer and inner diameters of the coil, measured with a ruler according to GOST 427, mm.

and the thickness of the foil or tape.

7.5 Measurement of the thickness of the ribbons, cut to length sheets and plates is carried out not less than 100 mm from the vertex of the angle and not less than 15 mm from the edge.

The thickness of the strips, cut into lengths, sheets and plates measured on each selected worksheet or each selected tape, cut to length, or the plate at points located uniformly randomly on the perimeter of the tape, cut to length, sheet or plate.

The number of strips, cut into lengths, sheets or plates in party M, EA, is calculated by the formula

(3)

where P is the weight of the batch, kg;

Y — material density, g/cm³;

H — the thickness of the strip, cut to length, sheet, mm;

b — belt width, cut to length, sheet or plate, mm;

l — belt length, cut to length, sheet or plate, mm.

Number of controlled sections in the ribbon, cut to length, sheet or plate N, EA, is calculated by the formula

(4)

where l is the tape length, cut to length, sheet or plate, mm;

b — belt width, cut to length, sheet or plate, mm.

7.6 the Width and length of the foil, ribbons, ribbon, cut into lengths, sheets and plates measuring ruler according to GOST 427, caliper according to GOST 166 or metal measuring tape according to GOST 7502.

The width measurement is carried out in a single place at a minimum distance of 100 mm from the end of the foil, tape or from the tape edges, cut to length or sheet.

7.7 Camber and deflection of foil, tapes and sheets is measured according to GOST 26877 in one place on any site.

7.8 Cosine of the cut strips, cut into lengths, sheets and plates determined according to GOST 26877.

7.9 For the tensile test from each selected roll of tape or sheet, or from each selected plate cut out on one sample. Sampling is carried out according to GOST 24047.

The tensile test is carried out according to GOST 11701 the samples of a type I or II tapes and sheets thickness less than 0.50 mm with l₀ = 4b₀ and b₀ = 12.5 mm; thickness from 0.50 mm to 3.00 mm with or and b₀= 20 mm.

Tensile test on strips of width less than 20 mm is carried out on samples having a width equal to the width of the tape, with the edges of samples can be processed mechanically.

Tensile testing of tapes and sheets with thickness of 3.0 mm and more is carried out according to GOST 1497 on samples of type II and / Or thickness from 3.00 to 8.00 with or and b₀= 20 mm; thickness of 8.00 mm and more or and b₀= 30 mm.

Tensile test on sheets and plates of a thickness more than 12 mm may be performed on cylindrical samples according to GOST 1497.

7.10 testing the hood spherical dimples each of the selected coil cut on the same model. The test is carried out according to GOST 10510.

Tape width up to 30 mm inclusive, and thickness up to 0.55 mm inclusive experience, a punch with a radius of 1.5 mm; a width of more than 30 to 90 mm inclusive, and thickness up to 0.55 mm inclusive, a punch with a radius of 4.0 mm; a width of over 90 mm and thickness more than 0.10 mm to 1.50 mm inclusive, a punch with a radius of 10 mm.

Allowed test on the hood of the spherical holes to hold up to the cutting of the ribbons to width.

Test on the hood of a spherical hole of ribbons with thickness from 0.10 to 0.45 mm may be performed on the machines in manual mode.

7.11 To determine the amount of grain from each selected coil cut on the same model. Determination of the grain is carried out according to GOST 21073.1

7.12 the bend Test is carried out according to GOST 14019.

Samples for bend test are cut along the rolling.

Samples for bend test of deoxidized copper should otjihase in a hydrogen environment at a temperature of from 800 °C to 850 °C for 30 min.

7.13 For the analysis of the chemical composition of each selected roll of tape, sheet or strip, cut to length, cut one sample. Sampling for chemical composition analysis is carried out according to GOST 24231.

Chemical composition analysis is carried out according to GOST 13938.1 — 13938.13 GOST, GOST 13938.15, GOST 9717.1 -GOST 9717.3.

Allowed to the manufacturer of the sampling carried out by the molten metal.

Allowed to carry out chemical analysis by other methods of equal precision specified. Allowed the manufacturer to control the impurity content of bismuth, antimony, arsenic, sulfur and oxygen periodically — once in three months provided the warranty of their content in accordance with the requirements of GOST 859.

If there is disagreement in the assessment of the chemical composition analysis is carried out according to GOST 13938.1 — 13938.13 GOST, GOST 13938.15.

7.14 Waviness of the edges of the test diffraction foil, ribbon, or sheet thickness up to 2.00 mm, inclusive, around a mandrel of diameter 100 to 120 mm. If the ripple does not disappear, the roll of foil, ribbon or sheet is rejected.

7.15 allowed the manufacturer to use other methods of control and measurement tools, providing the necessary accuracy.

If there is disagreement in the definition of indicators monitoring is carried out by methods specified in this standard.

7.16 Determination of specific volume electrical resistance is carried out according to GOST 7229.

Allowed other methods and means of measurement to ensure accuracy not lower than the established GOST 7229.

In the event of dispute, the measurement is carried out according to GOST 7229.

7.17 to determine compliance with the limits specified in this standard measured or calculated value obtained when testing shall be rounded in one step to the number of digits used to Express these limits in this standard.

Should be used the following rounding rules:

a) if the digit to the remaining immediately after the last digit less than 5, last remaining digit must remain unchanged;

b) if the number prevailing immediately after the last digit equal to or greater than 5, last remaining digit must be increased by one.

8 Marking, packaging, transportation and storage

8.1 the Foil and tape should be rolled up into rolls. One roll should not be more than three segments.

The inner diameter of the coil should be 40, 80, 100, 200, 250, 300, 400, 500 mm. Winding should avoid changing the shape of the coil under the action of gravity. By agreement with the consumer allowed other diameters of the coils.

8.2 the Rolls of foil and strips with thickness up to 0.50 mm, inclusive, should be wrapped in paper, Packed into wooden crates and shifted the cardboard.

Coils of strips with thickness more than 0.5 mm should be wrapped with tape of size not less than 0,220 mm and wrapped in synthetic or nonwoven material, ensure quality safety of products.

8.3 Tape, cut to length and cold-rolled sheets with a thickness up to 2.00 mm must be Packed in wooden boxes.

Allowed tape, cut to length and cold-rolled sheets with a thickness up to 2.00 mm inclusive packaging in bundles. Packs should be wrapped in paper and protected top and bottom with boards or wooden boards, the dimensions of which correspond to the width and length of the bundles, and tied in at least two areas or cross band size not less than 0,320 mm or a wire with a minimum thickness of 2 mm. Binding: wire — stranding at least three turns of tape to the castle.

Tape, cut to length, cold-rolled sheets with a thickness more than 2.00 mm and hot-rolled sheets must be Packed in bundles with double-sided protection shields the size of a pack as described above.

Sheets with a length of 4 m or more should be bent to touch the edges.

8.4 boards are put in wooden crates. Top plate cover with cardboard. Slab tie in at least two locations in the transverse and longitudinal directions with a tape of size not less than 0,820 mm.

8.5 as packaging AIDS and materials and means of fastening should be used:

paper according to GOST 8273;

— corrugated cardboard according to GOST 7376;

— cardboard according to GOST 7933;

— wooden boxes of types I, II, III according to GOST and GOST 2991 10198.

Dimensions of boxes — GOST 21140 or technical documents;

— Board technical documentation;

— synthetic and nonwovens for technical documents;

tape according to GOST 3560;

— wire according to GOST 3282.

It is possible to use other types of packaging and packaging materials not inferior in strength to the above and ensure quality safety of products.

8.6 To each coil or bundle or on each plate should be attached a label showing:

— trademark or name and trademark of manufacturer;

— the name of the country of manufacturer;

— the legend foil, ribbons, sheets and plates;

— batch number;

— stamp of technical control.

8.7 Without packaging in boxes, paper, and synthetic nonwoven materials is allowed to transport coils and packs in the containers according to the GOST 15102, GOST 22225, 20435 GOST 18477 and GOST in a single address without reloading on the way. In this case, between rows of bales and bundles must be laid corrugated cardboard according to GOST 7376.

During transportation in containers, coils and bundles must be stacked and fortified in such a way as to prevent their movement in the container. In addition, coils and bundles shall be protected against corrosion, contamination and mechanical damage.

8.8 In each box or container must be attached to the packing slip, containing:

is the trademark or name and trademark of manufacturer;

— the name of the country of manufacture;

— the symbol foil, ribbons, sheets and plates;

— the batch number;

— the net weight;

— gross mass;

— the number of the packer.

8.9 Transport marking under GOST 14192 with the application of manipulation sign «Protect from moisture».

8.10 Consolidation packages in overpacks carried out in accordance with the requirements of GOST 26663. Means bonding in the transport packets according to GOST 21650.

Packaging is carried out on pallets according to GOST 9557 or GOST 9078 or without pallets with the use of bars with a height of not less than 50 mm with strapping in the longitudinal and transverse directions with wire of diameter not less than 2 mm according to GOST 3282 or tape not less than 0,320 mm according to GOST 3560. Binding: wire — stranding at least five turns of tape to the castle.

Weight of cargo must not exceed 2000 kg. Weight of cargo space in covered wagons should not exceed 1250 kg.

8.11 Packaging foil, ribbons, sheets and plates sent to the far North regions and equated areas according to GOST 15846 in the group «Metals and metal products.»

8.12 Foil, strip, sheet and plate transporterowych all types of transport in covered vehicles in accordance with cargo carriage regulations applicable to transport of this species.

8.13 Foil, ribbons, sheets and plates should be stored in covered premises. When storing and transporting the foil, ribbons, sheets and plates shall be protected from mechanical damage, moisture and active chemical substances.

The consumer foil, strip, sheet and plate should be kept in stock in the manufacturer’s packaging for at least two days to equalize the temperature of the foil, ribbons, sheets and plates to the room temperature. At expiration, foil, strip, sheet and plate needs to be unpacked.

Under specified storage conditions consumer properties of the copper foil, ribbons, sheets and plates in storage do not change.

Annex a (informative)

Theoretical mass of 1 m2 of the copper foil, tapes and sheets

Ttable A. 1

Thickness, mm	Weight of 1 m2, kg	Thickness, mm	Weight of 1 m2, kg
0,05	0,44	1,50	13,35
0,06	0,53	1,60	14,24
0,07	0,62	1,70	15,13
0,08	0,71	1,80	Of 16.02
0,09	0,80	1,90	16,91
0,10	0,89	Of 2.00	17,80
0,12	Of 1.07	2,20	19,58
0,14	1,25	2,50	22,25
0,15	1,33	Of 3.00	Was 26.70
0,16	1,42	3,50	31,15
0,18	1,60	Of 4.00	35,60
0,20	1,78	4,50	Of 40.05
0,22	1,96	5,00	44,50
0,25	Of 2.23	5,50	48,95
0,28	2,49	6,00	53,40
0,30	2,67	6,50	57,85
0,35	3,12	7,00	62,30
0,40	3,56	8,00	71,20
0,45	Of 4.01	9,00	80,10
0,50	4,45	10,00	89,00
0,55	4,90	11,00	Of 97.90
0,60	5,34	12,00	106,80
0,65	5,79	13,00	115,70
0,70	6,23	14,00	124,60
0,75	6,68	15,00	133.50 against
0,80	7,12	16,00	142,40
0,85	7,57	17,00	Of 151.30
0,90	8,01	18,00	160,20
Of 1.00	8,90	19,00	169,10
1,05	9,35	20,00	178,00
1,10	Of 9.79	22,00	195,80
1,20	10,68	24,00	213,60
1,30	Of 11.57	25,00	222,50
1,40	12,46
Note — the Theoretical mass calculated with the nominal thickness and density of copper, equal to 8.9 g/cm3.

Annex B (informative)

Compliance designations copper grades according to GOST 1173−2006 and EN 1652:1998

Ttable B. 1

GOST 1173−2006	EN 1652:1998
M1F	Cu-DHP
M1r	Cu-DLP
M1	Cu-ETP

Annex b (informative)

Hardness values

Ttable B. 1

The condition of the material	Brinell hardness number not less than	The Vickers hardness
Soft	55	40 — 65
Semi-solid	75	65 — 95
Solid	95	90 — 110