GOST 15834-2016

• gost-15834-2016.pdf (1.33 MiB)
  ГОСТ 15834-2016

GOST 15834−2016 Wire of beryllium bronze. Specifications

GOST 15834−2016

Group В74

INTERSTATE STANDARD

WIRE OF BERYLLIUM BRONZE

Specifications

Wire of beryllium bronze. Technical conditions

ISS 77.150.30
GST 18 4690

Date of introduction 2017−04−01

Preface

Goals, basic principles and main procedure of works on interstate standardization have been established in GOST 1.0−2015 «interstate standardization system. Basic provisions» and GOST 1.2−2015 «interstate standardization system. Interstate standards, rules and recommendations on interstate standardization. Rules of development, adoption, renewal and cancellation"
Data on standard

1 DEVELOPED by the Technical Committee for standardization TC 106 «Tsvetmetprokat», Scientific-research, project and design Institute for alloys and processing of nonferrous metals «Joint-stock company «Institute tsvetmetobrabotka» (JSC «Institute tsvetmetobrabotka»)

2 as AMENDED by the Federal Agency for technical regulation and Metrology

3 ACCEPTED by the Interstate Council for standardization, Metrology and certification (Protocol dated February 29, 2016 N 85-P)

The adoption voted:

4 by Order of the Federal Agency for technical regulation and Metrology dated July 26, 2016 N 882-St inter-state standard GOST 15834−2016 introduced as a national standard of the Russian Federation from April 1, 2017

5 REPLACE GOST 15834−77

Information about the changes to this standard is published in the annual reference index «National standards», and the text changes and amendments — in monthly information index «National standards». In case of revision (replacement) or cancellation of this standard a notification will be published in the monthly information index «National standards». Relevant information, notification and lyrics are also posted in the information system of General use — on the official website of the Federal Agency for technical regulation and Metrology on the Internet (www.gost.ru)

1 Scope

This standard applies to wire round beryllium bronze (hereinafter, wire) used in instrument and mechanical engineering.

This standard specifies the dimensions, technical requirements, acceptance rules, methods of control and testing, packaging rules, marking, transportation and storage of the wire.

2 Normative references

This standard uses the regulatory references to the following international standards:

GOST 2991−85 wooden disposable Boxes for loads up to 500 kg. General specifications

The Wire GOST 3282−74 General purpose low carbon steel. Specifications

GOST 3560−73 package steel Strip. Specifications

GOST 4381−87 Micrometers lever. General specifications

GOST 6507−90 Micrometers. Specifications

GOST 8273−75 wrapping Paper. Specifications

GOST 8828−89 base Paper and paper double-layer waterproof packaging. Specifications

GOST 9078−84 flat Pallets. General specifications

GOST 9347−74 Cardboard gasket and gasket from him. Specifications

GOST 9421−80 Cardboard glued flat container. Specifications

GOST 9557−87 flat wooden Pallet size of 8001200 mm. Technical specifications

GOST 9570−84 box Pallets and rack. General specifications

GOST 10446−80 (ISO 6892−84) Wire. Test method tensile

GOST 10447−93 Wire. Method of test for winding

GOST 14192−96 Marking of cargo

GOST 15027.1−77 Bronze without tin. Method for determination of copper

GOST 15027.2−77 Bronze without tin. Method for the determination of aluminium

GOST 15027.3−77 Bronze without tin. Method for determination of iron

GOST 15027.5−77 Bronze without tin. Method for the determination of Nickel

GOST 15027.7−77 Bronze without tin. Method for determination of lead

GOST 15027.13−77 Bronze without tin. Method for the determination of beryllium

GOST 15846−2002 Products that are sent to the far North regions and equated areas. Packing, marking, transportation and storage

GOST 18175−78 of Bronze without tin pressure treated. Brand

GOST 18242−72 Statistical acceptance inspection by alternative feature. Plans control
_______________
In the Russian Federation GOST R ISO 2859−1-2007 «Statistical methods. Procedure sampling on alternative grounds. Part 1. Sampling plans consistent parties on the basis of an acceptable level of quality."


GOST 18321−73 Statistical quality control. Methods of random selection of piece products

GOST 20435−75 the universal metal closed Container of nominal gross mass 3,0 t specifications

GOST 21073.0−75 ferrous Metals. Determination of grain size. General requirements

GOST 21073.1−75 ferrous Metals. Determination of grain size by comparison with the scale of microstructures

GOST 21073.2−75 ferrous Metals. Determination of grain size by the method of counting beans

GOST 21073.3−75 ferrous Metals. Determination of grain size by the method of counting intersections bean

GOST 21073.4−75 ferrous Metals. Determination of grain size planimetric method

GOST 21650−76 means of fastening of package cargoes in transport packages. General requirements

GOST 22225−76 universal Containers with a gross weight 0,625 and 1,25 t. specifications

GOST 24231−80 non-ferrous metals and alloys. General requirements to selection and preparation of samples for chemical analysis

GOST 24597−81 the packaged goods. Basic parameters and dimensions

GOST 26653−90 Preparation of General cargoes for transportation. General requirements

GOST 26663−85 transport Packs. Formation with the use of packaging. General technical requirements

GOST 32597−2013 Copper and copper alloys. Types of defects of billets and semi-finished

ST SEV 543−77 Number. Record rules and rounding

Note — When using this standard appropriate to test the effect of reference standards in the information system of General use — on the official website of the Federal Agency for technical regulation and Metrology on the Internet or in the annual information index «National standards» published as on January 1 of the current year, and the editions of the monthly information index «National standards» for the current year. If the reference standard is replaced (changed), when using this standard should be guided by the replaced (amended) standard. If the reference standard is cancelled without replacement, then the situation in which the given link applies to the extent that does not affect this link.

3 Terms and definitions

This standard applies the terminology according to GOST 32597, as well as the following terms with respective definitions:

3.1 wire: Prefabricated with a cross section of constant size, rolled into the Bay or wound into a coil, manufactured by rolling, pressing or drawing.

3.2 Bay: Cut product wound into a series of continuous coils is correct, not mixed up in rows, with no sharp bends.

4 Assortment

4.1 wire Diameter and tolerances for diameter shall be as specified in table 1.

Table 1

4.2 out-of-Roundness of the wire must not exceed the limit deviation for diameter.

Note — At the customer’s request wire produced with ovality not exceeding half of the maximum deviations in diameter.

4.3 Wire is supplied in coils, Hanks or on reels.

4.4 callout wire is placed according to the scheme:

The sign «X» in the diagram stands for data that has more than one value.

Use the following abbreviations: