GOST 19045-80
GOST 19045−80 cutting Inserts, replaceable carbide faceted triangular shape with a clearance angle of 11°. The design and dimensions (with Amendments No. 1, 2)
GOST 19045−80
Group B56
INTERSTATE STANDARD
CUTTING INSERTS, REPLACEABLE CARBIDE FACETED
TRIANGULAR SHAPE WITH A CLEARANCE ANGLE OF 11°
The design and dimensions
Triangular throw-away (indexable) carbide cutting inserts
with 11° end-clearance angle. Design and dimensions
ISS 25.100
77.160
OKP 19 6000
Date of introduction 1982−01−01
INFORMATION DATA
1. DEVELOPED AND INTRODUCED by the Ministry of nonferrous metallurgy of the USSR
2. APPROVED AND put INTO EFFECT by Decision of the USSR State Committee for standards from
3. In this standard introduced by the international standard ISO 883−85 «Plate replaceable tungsten carbide (carbide) with radii without fixing holes. Dimensions» in terms of inserts TPUN, TPGN
4. REPLACE GOST 19045−73
5. REFERENCE NORMATIVE AND TECHNICAL DOCUMENTS
| The designation of the reference document referenced |
Item number |
| GOST 19042−80 |
4 |
| GOST 19086−80 |
5 |
6. The expiration time limit is removed by the Resolution of Gosstandart of the USSR from
7. EDITION with Amendments No. 1, 2 approved in October 1984, December 1990 (IUS 2−85, 4−91).
The requirements of this standard are mandatory.
(Added, Rev. N 2).
1. (Deleted, Rev. N 2).
2. The design and dimensions of plates shall be as specified in the drawing and in the table.
________________
* Size for reference.
mm
| The marking plates of classes of tolerances |
||||||||||
| U | G | |||||||||
| digital | alphanumeric | When- me- the need* |
digital | alpha digital |
When- me- the cost |
|||||
| - | - | 01331−110300 |
TPGN-110300 | 11,0 | 6,350 | 3,18 | 0,2 | 9,325 | ||
| 01311−110304 |
TPUN-110304 | 01331−110304 |
TPGN-110304 | 0,4 | 9,128 | |||||
| 01311−110308 |
TPUN-110308 | 01331−110308 |
TPGN-110308 | 0,8 | 8,731 | |||||
| 01311−160300 |
TPUN-160300 |
01331−160300 |
TPGN-160300 | 16,5 | 9,525 | 0,2 | 14,088 | |||
| 01311−160304 |
TPUN-160304 | 01331−160304 |
TPGN-160304 | 0,4 | 13,891 | |||||
| 01311−160308 |
TPUN-160308 | 01331−160308 | TPGN-160308 | 0,8 | 13,494 | |||||
| 01311−160312 |
TPUN-160312 | 01331−160312 | TPGN-160312 | 1,2 | 13,097 | |||||
| - |
- | 01331−160408 | TPGN-160408 | 4,76 | 0,8 | 13,494 | ||||
| 01311−220408 |
TPUN-220408 | 01331−220408 | TPGN-220408 | 22,0 | 12,700 | 0,8 | 18,256 | |||
| 01311−220412 |
TPUN-220412 | 01331−220412 | TPGN-220412 | 1,2 | 17,859 | |||||
| 01311−220416 |
TPUN-220416 | 01331−220416 | TPGN-220416 | 1,6 | 17,463 | |||||
| 01311−270616 |
TPUN-270616 | - | - | 27,5 | 15,875 | 6.35 mm | 1,6 | 22,225 | ||
________________
* See Appendix 3.
Example of designation when ordering plates of solid alloy grade VK6-OM, class of admission U, with cutting edge length =11.00 mm, thickness
=3.18 million, radius
=0.4 mm:
19 6516
0357 110304
3. Approximate weight plates specified in Appendix 1.
4. The notation of plates according to GOST 19042.
5. Technical requirements — GOST 19086.
6. Applicable grades listed in Appendix 2.
(Added, Rev. N 2).
ANNEX 1
Reference
Approximate weight plates
| Approximate weight of plates, g | |||||||||||
| Digital signage plates | carbide grades | from without- wolf- ramovic solid alloys |
of hard alloy with wear-resistant coating | ||||||||
| VK6-OM | VK6 |
VK8 | Т5К10 | Т14К8 | T15K6 | Т30К4 | КНТ16, ТН20 |
ВП3325 | ВП1255 | ВП3115 | |
| 01331−110300 |
2,01 | 2,01 | 1,99 | 1,74 | 1,58 | 1.55 V | 1,32 | 0,79 | 1,99 | 1,84 | 2,01 |
| 01311−110304 |
2,01 | 2,01 | 1,98 | 1,74 | 1,57 | 1.55 V | 1,32 | 0,78 | 1,98 | 1,84 | 2,01 |
| 01331−110304 |
|||||||||||
| 01313−110308 |
1,99 | 1,99 | 1,96 | 1,72 | 1,56 | 1,53 | 1,30 | 0,77 | 1,96 | 1,83 | 1,99 |
| 01331−110308 |
|||||||||||
| 01311−160300 |
4,87 | 4,87 | 4,81 | 4,22 | 3,82 | 3,76 | 3,20 | 1,90 | 4,81 | 4,48 | 4,87 |
| 01331−160300 |
|||||||||||
| 01311−160304 |
4,85 | 4,85 | 4,79 | 4,20 | 3,80 | 3,74 | 3,18 | 1,89 | 4,79 | 4,48 | 4,85 |
| 01331−160304 |
|||||||||||
| 01311−160308 |
4,83 | 4,83 | 4,76 | 4,18 | 3,78 | 3,72 | 3,16 | Of 1.88 | 4,76 | 4,48 | 4,83 |
| 01331−160308 |
|||||||||||
| 01331−160408 |
6,75 | 6,75 | Of 6.66 | 5,86 | 5,31 | 5,22 | 4,42 | 2,63 | Of 6.66 | 6,21 | 6,75 |
| 01311−220408 |
12,67 | 12,67 | 12,50 | 11,00 | 9,93 | 9,76 | 8,30 | - | 12,50 | 11,65 | 12,67 |
| 01331−220408 |
|||||||||||
| 01311−220412 |
12,66 | 12,60 | Of 12.40 | 10,90 | For 9.88 | Of 9.71 | 8,26 | - | Of 12.40 | At 11.59 | 12,60 |
| 01331−220412 |
|||||||||||
| 01311−220416 |
12,50 | 12,50 | 12,30 | 10,80 | 9,76 | 9,59 | 8,16 | - | 12,30 | 11,50 | 12,50 |
| 01331−220416 |
|||||||||||
| 01311−270616 |
26,00 | 26,00 | 25,60 | 22,50 | 20,40 | 20,00 | 17,00 | - | 25,60 | 23,92 | 26,00 |
| 01311−160312 |
4,77 | 4,77 | 4,71 | 4,13 | 3,74 | 3,68 | 3,13 | 1,86 | 4,71 | - | 4,77 |
| 01331−160312 |
|||||||||||
APPENDIX 2 (recommended). Applied grades of plates
ANNEX 2
Recommended
| Digital signage plates |
The main application | The additional use of | Application by special order |
| 01331−110300 |
N 7, N 12 | N 2 | N 3, N 4, N 5, N 6, N 8, N 9, N 10 |
| 01311−110304 | N 3, N 7, N 12, N 9, N 10 |
N 2 | N 4, N 5, N 6, N 8, N 11 |
| 01331−110304 | N 5, N 7, N 12, N 9 | N 2 | N 3, N 4, N 6, N 8, N 10, N 11 |
| 01311−110308 |
N 3, N 7, N 9, N 10, N 11 | N 2, N 12 | N 4, N 5, N 6, N 8 |
| 01331−110308 |
N 3, N 7, N 9, N 10, N 11 | N 2, N 12 | N 4, N 5, N 6, N 8 |
| 01311−160300 |
- | - | N 2, N 3, N 4, N 5, N 6, N 7, N 12, N 8, N 9, N 10, N 11 |
| 01331−160300 |
N 7, N 12 | N 2 | N 3, N 4, N 5, N 6, N 8, N 9, N 10, N 11 |
| 01311−160304 |
N 3, N 7, N 9, N 10, N 11 | N 2, N 12 | N 4, N 5, N 6, N 8 |
| 01331−160304 |
N 7 | N 2, N 12 | N 3, N 4, N 5, N 6, N 8, N 9, N 10, N 11 |
| 01311−160308 |
N 3, N 7, N 9, N 10, N 11 | N 2 | N 4, N 5, N 6, N 12, N 8 |
| 01331−160308 |
N 3, N 5, N 6, N 7, N 9, N 10, N 11 |
N 2, N 12 | N 4, N 8 |
| 01311−160312 |
N 3, N 7, N 9, N 10, N 11 | - | N 2, N 4, N 5, N 6, N 12, N 8 |
| 01331−160312 |
N 3, N 6, N 7, N 9, N 10, N 11 |
N 2, N 5 | N 4, N 12, N 8 |
| 01331 — 160408 |
N 5, N 7, N 9, N 10, N 11 | N 2, N 4 | N 3, N 6, N 12, N 8 |
| 01311−220408 |
N 3, N 4, N 5, N 7, N 9, N 10, N 11 |
N 2 | N 6, N 12 |
| 01331−220408 | - | - | N 2, N 3, N 4, N 5, N 6, N 7, N 12, N 9, N 10, N 11 |
| 01311−220412 | N 4, N 5, N 6, N 7, N 9, N 10, N 11 |
N 2 | N 3, N 12 |
| 01331−220412 |
N 4, N 5, N 9, N 10, N 11 | N 2, N 7 | N 3, N 6, N 12 |
| 01311−220416 |
N 5, N 7, N 10 | - | N 2, N 3, N 4, N 6, N 9, N 11, N 12 |
| 01331−220416 |
- | - | N 2, N 3, N 4, N 5, N 6, N 7, N 9, N 10, N 12 |
| 01311−270616 | N 5, N 7 |
- | N 2, N 3, N 4, N 5, N 8, N 9, N 10, N 12 |
N 2 — VK6-OM; N 3 — VK6; N 4 — VK8; N 5 — Т5К10; N 6 — Т14К8; N 7 — T15K6; N 8 — КНТ16; ТН20; N 9 — ВП3115; N 10 — ВП3325; N 11 — ВП1255; N 12 — Т30КН
APPENDIX 3 (reference). The use of plates
APPENDIX 3
Reference
Rear angle |
Plate classes tolerances U, G | |||||
| Without chip breaking C-geometry of the grooves (N) | ||||||
| Marking |
the radius | |||||
| 0,4 |
0,8 | 1,2 | 1,6 | |||
| 6.35 mm | 11° | TPUN 1103 |
+ | + | +++ | ++ |
| TPGN 1103 |
+ | +++ | +++ | ++ | ||
| 9,525 | TPUN 1603 | + | + | + | ++ | |
| TPGN 1603 | +++ | + | + | ++ | ||
| 12,7 | TPUN 2204 | ++ | + | + | + | |
| TPGN 2204 | ++ | +++ | + | +++ | ||
Note. + — plates of the basic application, standardized.
++ — plates have limited use, not standardized.
+++ — plates are not recommended for use.
APP 2, 3. (Added, Rev. N 2).
