GOST 19046-80
GOST 19046−80 cutting Inserts, replaceable carbide faceted triangular shape with a hole and a chip breaking C-grooves on one side. The design and dimensions (with Amendments No. 1, 2)
GOST 19046−80
Group 56
INTERSTATE STANDARD
CUTTING INSERTS, REPLACEABLE CARBIDE FACETED
TRIANGULAR SHAPE WITH A HOLE AND A CHIP BREAKING C —
GROOVES ON ONE SIDE
The design and dimensions
Triangular throw-away (indexable) carbide cutting inserts with cylindrical
holes and chip-breaking flutes on one face only. Design and dimensions
ISS 25.100
77.160
OKP 19 6000
Date of introduction 1982−01−01
INFORMATION DATA
1. DEVELOPED AND INTRODUCED by the Ministry of ferrous metallurgy of the USSR
2. APPROVED AND put INTO EFFECT by Decision of the USSR State Committee for standards from
3. In this standard introduced by the international standard ISO 3364−85 «Plate replaceable tungsten carbide with corner radii with cylindrical fixing hole. Dimensions» in terms of inserts TNMM
4. REPLACE GOST 19046−80
5. REFERENCE NORMATIVE AND TECHNICAL DOCUMENTS
| The designation of the reference document referenced |
Item number |
| GOST 19042−80 |
4 |
| GOST 19086−80 |
5 |
6. The expiration time limit is removed by the Resolution of Gosstandart of the USSR from
7. EDITION with Amendments No. 1, 2 approved in October 1984, December 1990 (IUS 2−85, 4−91)
The requirements of this standard are mandatory.
(Added, Rev. N 2).
1. (Deleted, Rev. N 2).
2. The design and dimensions of plates shall be as specified in the drawing and in the table.
________________
* Size for reference.
mm
| The marking plates of classes of tolerances |
|||||||||||
| U |
M | ||||||||||
| digital | alpha digital |
When- me- the need* |
digital | alpha digital |
When- me- the need* |
||||||
| 01114−160304 |
TNUM-160304 | 01124−160304 | TNMM-160304 | 16,5 | 9,525 | 3,81 | 3,18 | 0,4 | 13,891 | ||
| 01114−160308 |
TNUM-160308 | 01124−160308 | TNMM-160308 | 0,8 | 13,494 | ||||||
| 01114−160312 |
TNUM-160312 | 01124−160312 | TNMM-160312 | 1,2 | 13,097 | ||||||
| 01114−160404 |
TNUM-160404 | 01124−160404 | TNMM-160404 | 4,76 | 0,4 | 13,891 | |||||
| 01114−160408 |
TNUM-160408 | 01124−160408 | TNMM-160408 | 0,8 | 13,494 | ||||||
| 01114−160412 |
TNUM-160412 | 01124−160412 | TNMM-160412 | 1,2 | 13,097 | ||||||
| 01114−220404 |
TNUM-220404 | 01124−220404 | TNMM-220404 | 22,0 | 12,700 | 5,16 | 4,76 | 0,4 | 18,653 | ||
| 01114−220408 |
TNUM-220408 | 01124−220408 | TNMM-220408 | 0,8 | 18,256 | ||||||
| 01114−220412 |
TNUM-220412 | 01124−220412 | TNMM-220412 | 1,2 | 17,859 | ||||||
| 01114−220416 |
TNUM-220416 | 01124−220416 | TNMM-220416 | 1,6 | 17,463 | ||||||
| 01114−270612 |
TNUM-270612 | 01124−270612 | TNMM-270612 | 27,5 | 15,875 | 6.35 mm | 6.35 mm | 1,2 | 22,622 | ||
| 01114−270616 |
TNUM-270616 | 01124−270616 | TNMM-270616 | 1,6 | 22,225 | ||||||
________________
* See Annex 4.
Example of designation when ordering plates of hard alloy VK6 brand, class M tolerance, cutting edge length =16,5 mm, thickness
=3.18 mm radius
=0.4 mm, with a chip breaking C-groove type 1:
19 6524
0360 160304−1
Same with chip breaking C-groove type 2:
19 6524
0360 160304−2
(Changed edition, Rev. N 2).
3. Type, form and dimensions of a chip breaking C-grooves are provided in Annex 1.
4. Approximate weight plates are given in Appendix 2.
5. The notation of plates according to GOST 19042.
6. Technical requirements — GOST 19086.
7. Applied alloys is given in Appendix 3.
(Added, Rev. N 2).
ANNEX 1
Recommended
Type, form and dimensions of a chip breaking C-grooves on the front surface of the plates is indicated on the devil.1−5 and in table.1 and 2.
Damn.1. Form 1 for the diameter d=9,525 mm. Form 2 for diameters d=12,700 15,875 mm mm Type 1
Type 1
Damn.1
Table 1
Dimensions, mm
| 9,525 |
- | 5 | 1,0 | 25° |
| 12,700 |
2,8 | - | 1,0 | 25° |
| 15,875 |
3,6 | - | 1,6 | 20° |
Damn.2. Form 1 for plates 011.4−160304−2; 011.4−220404−2; 011.4−160404−2. Type 2
Form 1 for plates 011.4−160304−2; 011.4−220404−2; 011.4−160404−2
Type 2
________________
* Dimensions for reference.
Damn.2
Damn.3. Form 2. Type 2
Form 2
Type 2
________________
* The transition between the main chip breaker and chip breaker at the top is aligned with the length of 1.5 mm.
** Size for reference.
Damn.3
Table 2
Dimensions, mm
| Plate |
|||||||||||||
| 011.4−160308−2 |
0,18 | 1,02 | 0,71 | 1,68 | 2,41 | 0,66 | 1,14 | 0,09 | 0,12 | 2,5 | 0,6 | 15° | 7° |
| 011.4−160408−2 |
|||||||||||||
| 011.4−160312−2 |
0,23 | Of 1.07 | 0,76 | 1,71 | 2,41 | 0,71 | 1,20 | 0,09 | 0,12 | 2,3 | 0,6 | 15° | 7° |
| 011.4−160412−2 |
|||||||||||||
| 011.4−220408−2 |
0,20 | 1,22 | 0,88 | 2,22 | 2,80 | 0,68 | 1,14 | 0,11 | 0,15 | 2,4 | 0,4 | 12° | 5° |
| 011.4−220412−2 |
0,25 | 1,27 | 0,93 | 2,27 | 2,85 | 0,73 | 1,20 | 0,11 | 0,15 | 2,4 | 0,4 | 12° | 5° |
| 011.4−270612−2 |
0,40 | 1,42 | Of 1.08 | 2,42 | Of 3.00 | 0,88 | 1,20 | 0,11 | 0,15 | 2,4 | 0,4 | 12° | 5° |
Damn.4. Form 3 for plates 011.4−220416−2. Type 2
Form 3 for plates 011.4−220416−2
Type 2
________________
* Dimensions for reference.
Damn.4
Damn.5. Form 4 for plates 011.4−270616−2. Type 2
Form 4 for plates 011.4−270616−2
Type 2
________________
* Dimensions for reference.
Damn.5
ANNEX 2 (informative). Approximate weight plates
ANNEX 2
Reference
| Approximate weight of plates, g | ||||||||
| Digital signage plates | carbide grades | of tungsten carbide |
hard alloy coated | |||||
| VK6 | VK8 | Т5К10 | T15K6 | КНТ16, ТН20 |
ВП3325 | ВП3115 | ВП1255 | |
| 01114−160304 |
4,71 | 4,65 | 4,11 | 3,65 | 1,84 | 4,65 | 4,71 | 4,33 |
| 01124−160304 |
||||||||
| 01114−160308 |
Of 4.66 | 4,60 | Of 4.03 | 3,59 | Of 1.82 | 4,60 | Of 4.66 | 4,48 |
| 01124−160308 |
||||||||
| 01114−160312 |
Of 4.59 | A 4.53 | Of 3.97 | 3,53 | 1,79 | A 4.53 | Of 4.59 | 4,22 |
| 01124−160312 |
||||||||
| 01114−160404 |
7,18 | 7,08 | 6,27 | 5,55 | 2,80 | 7,08 | 7,18 | 6,60 |
| 01124−160404 |
||||||||
| 01114−160408 |
7,12 | Of 7.03 | 6,16 | 5,49 | Of 2.78 | Of 7.03 | 7,12 | 6,55 |
| 01124−160408 |
||||||||
| 01114−160412 | Of 7.01 | Of 6.91 | 6,06 | 5,40 | 2,73 |
Of 6.91 | Of 7.01 | 6,53 |
| 01124−160412 |
||||||||
| 01114−220404 |
12,60 | Of 12.40 | 10,90 | 9,73 | - | Of 12.40 | 12,60 | At 11.59 |
| 01124−220404 |
||||||||
| 01114−220408 |
12,60 | Of 12.40 | 10,90 | 9,70 | - | Of 12.40 | 12,60 | At 11.59 |
| 01124−220408 |
||||||||
| 01114−220412 |
12,50 | 12,30 | 10,80 | Of 9.61 | - | 12,30 | 12,50 | 11,50 |
| 01124−220412 |
||||||||
| 01114−220416 |
12,30 | 12,20 | 10,70 | 9,49 | - | 12,20 | 12,30 | Of 11.31 |
| 01124−220416 |
||||||||
| 01114−270612 |
Of 26.30 | 25,90 | 22,70 | 20,20 | - | 25,90 | Of 26.30 | Of 24.19 |
| 01124−270612 |
||||||||
| 01114−270616 |
26,00 | 25,70 | 22,50 | 20,10 | - | 25,70 | 26,00 | 23,92 |
| 01124−270616 |
||||||||
APPENDIX 2. (Changed edition, Rev. N 2).
APPENDIX 3 (recommended). Applied grades of plates
APPENDIX 3
Recommended
| Digital signage plates |
The main application |
Additional additional application |
Application by special order |
| 01114−160304 |
N 3, N 7 | - | N 4, N 5, N 8, N 10, N 9, N 11 |
| 01124−160304 |
N 3, N 7 | N 4, N 5, N 8, N 10, N 9, N 11 | |
| 01114−160308 |
N 3, N 7, N 9, N 11 | N 4, N 5, N 8, N 10 | |
| 01124−160308 |
- | N 3, N 4, N 5, N 7, N 8, N 9, N 10, N 11 | |
| 01114−160312 |
N 3, N 4, N 5, N 7, N 8, N 9, N 10, N 11 | ||
| 01124−160312 |
|||
| 01114−160404 |
|||
| 01124−160404 |
|||
| 01114−160408 |
N 3, N 7, N 9, N 11 | N 5 | N 4, N 5, N 8, N 10 |
| 01124−160408 |
|||
| 01114−160412 |
N 3, N 7, N 9, N 11 | - | N 4, N 8, N 10 |
| 01124−160412 |
- | N 3, N 4, N 5, N 7, N 8, N 10, N 9, N 11 | |
| 01114−220404 |
N 3, N 4, N 5, N 7, N 8, N 9, N 10, N 11 | ||
| 01124−220404 |
|||
| 01114−220408 |
N 3, N 5, N 7, N 9 | N 4, N 10, N 11 | |
| 01124−220408 |
|||
| 01114−220412 | N 3, N 4, N 5, N 7, N 10, N 11 |
N 4 | - |
| 01124−220412 | N 3, N 5, N 7, N 9, N 11 |
- | N 10 |
| 01114−220416 | N 3, N 4, N 5, N 6, N 7, N 9, N 10, N 11 |
- | |
| 01114−220416 | N 4, N 5, N 6, N 7, N 9, N 10, N 11 |
N 3 | |
| 01114−270612 |
N 4, N 5, N 7, N 10, N 11 | - | N 3, N 9 |
| 01124−270612 |
|||
| 01114−270616 |
N 4, N 5, N 7, N 10 | N 3, N 9, N 11 | |
| 01124−270616 |
N 3 — VK6; N 4 — VK8; N 5 — Т5К10; N 7 — T15K6; N 8 — КНТ16, ТН20; N 9 — ВП3115; N 10 — ВП3225; N 11 — ВП1255.
ANNEX 4 (reference). The applicability of the plates
ANNEX 4
Reference
| Marking | Plate with a chip breaking C-grooves on one side | |||||
the radius | ||||||
| 0,4 | 0,8 | 1,2 | 1,6 | 2,4 | ||
| 6.35 mm | TNMM 1103 |
++ | ++ | +++ | +++ | +++ |
| 9,525 | TNMM 1603 |
++ | ++ | ++ | +++ | +++ |
| TNMM 1604 |
++ | + | + | ++ | +++ | |
| 12,7 | TNMM 2204 |
++ | + | + | + | +++ |
| 15,875 | TNMM 2706 |
+++ | +++ | + | + | ++ |
| 19,05 | TNMM 3309 |
+++ | +++ | +++ | +++ | ++ |
Note. + — plates of the basic application, standardized.
++ — plates have limited use, not standardized.
+++ — plates are not recommended for use.
APPS 3, 4. (Added, Rev. N 2).
