GOST 19044-80

STATE 12339-2016 GOST P 55433-2013 GOST P 55432-2013 GOST 4960-2009 GOST 9722-97 GOST 5494-95 GOST 19106-73 GOST 9453-75 GOST 20559-75 GOST 14086-68 GOST 9723-73 GOST 21125-75 GOST 5426-76 GOST 22025-76 GOST 13834-77 GOST 13833-77 GOST 9721-79 GOST 10285-81 GOST 12342-81 GOST 26719-85 GOST 13084-88 GOST 10096-76 GOST 2330-76 GOST 12343-79 GOST 4411-79 GOST 12338-81 GOST 26252-84 GOST 10284-84 GOST 26802-86 GOST 9849-86 GOST 3882-74 GOST 880-75 GOST 11378-75 GOST 4960-75 GOST 12601-76 GOST 12339-79 GOST 31290-2005 GOST 26630-85 GOST 26530-85 GOST 29278-92 GOST 25405-90 GOST 19046-80 GOST 25406-90 GOST 19078-80 GOST 24257-80 GOST 19065-80 GOST 24247-80 GOST 25412-90 GOST 25396-90 GOST 25400-90 GOST 25425-90 GOST 25410-82 GOST 25420-90 GOST 19074-80 GOST 19083-80 GOST 19048-80 GOST 25414-90 GOST 19062-80 GOST 25415-90 GOST 24253-80 GOST 24251-80 GOST 24249-80 GOST 24254-80 GOST 27302-87 GOST 25393-90 GOST 19067-80 GOST 25411-90 GOST 19068-80 GOST 25397-90 GOST 19059-80 GOST 19049-80 GOST 25398-90 GOST 19075-80 GOST 19061-80 GOST 20312-90 GOST 19051-80 GOST 25402-90 GOST 24252-80 GOST 25417-82 GOST 19043-80 GOST 20771-82 GOST 19081-80 GOST 19086-80 GOST 19056-80 GOST 19047-80 GOST 25421-90 GOST 25413-82 GOST 25418-82 GOST 27301-87 GOST 4872-75 GOST 19084-80 GOST 24255-80 GOST 19050-80 GOST 25401-90 GOST 19052-80 GOST 25426-90 GOST 25423-90 GOST 25399-90 GOST 19073-80 GOST 19057-80 GOST 2209-90 GOST 25403-82 GOST 19044-80 GOST 25408-90 GOST 25395-90 GOST 25409-90 GOST 25407-90 GOST 19071-80 GOST 28378-89 GOST 25419-90 GOST 19045-80 GOST 25003-81 GOST 25394-90 GOST 19077-80 GOST 19072-80 GOST 19080-80 GOST 17163-90 GOST 24250-80 GOST 25424-90 GOST 19063-80 GOST 19070-80 GOST 19076-80 GOST 24256-80 GOST 25422-90 GOST 25404-90 GOST 19064-80 GOST 24248-80 GOST 19069-80 GOST 19079-80 GOST 25416-90 GOST 19053-80 GOST 19042-80 GOST 19085-80

gost-19044-80.pdf (189.82 KiB)
ГОСТ 19044-80

GOST 19044−80 cutting Inserts, replaceable carbide faceted triangular shape with a hole. The design and dimensions (with Amendments No. 1, 2)

GOST 19044−80

Group 56

INTERSTATE STANDARD

CUTTING INSERTS, INDEXABLE MULTI-FACETED
CARBIDE TRIANGULAR SHAPE WITH HOLE

The design and dimensions

Triangular throw-away (indexable) carbide cutting
inserts with cylindrical holes. Design and dimensions

ISS 25.100
77.160
OKP 19 6000

Date of introduction 1982−01−01

INFORMATION DATA

1. DEVELOPED AND INTRODUCED by the Ministry of nonferrous metallurgy of the USSR

2. APPROVED AND put INTO EFFECT by Decision of the USSR State Committee for standards from 19.06.80 N 2904

3. In this standard introduced by the international standard ISO 3364−85 «Plate replaceable tungsten carbide with corner radii with cylindrical fixing hole. Dimensions» in terms of inserts TNMA

4. REPLACE GOST 19044−73

5. REFERENCE NORMATIVE AND TECHNICAL DOCUMENTS


The designation of the reference document referenced	Item number
GOST 19042−80	4
GOST 19086−80	5

6. The expiration time limit is removed by the Resolution of Gosstandart of the USSR from 29.12.90 N 3610

7. EDITION with Amendments No. 1, 2 approved in October 1984, December 1990 (IUS 2−85, 4−91)

The requirements of this standard are mandatory.

(Added, Rev. N 2).

1. (Deleted, Rev. N 2).

2. The design and dimensions of plates shall be as specified in the drawing and in the table

ГОСТ 19044-80 Пластины режущие сменные многогранные твердосплавные трехгранной формы с отверстием. Конструкция и размеры (с Изменениями N 1, 2)

________________
* Dimensions for reference.


Marking plates class U tolerance
digital	alphanumeric	Prima — reemote*
01113−110304	TNUA-110304		11,0	6,350	2,26	3,28	0,4	9,128
01113−110308	TNUA-110308						0,8	8,731
01113−160308	TNUA-160308		16,5	9,525	3,81		0,8	13,494
01113−160312	TNUA-160312						1,2	13,097
01113−160404	TNUA-160404					4,76	0,4	13,897
01113−160408	TNUA-160408						0,8	13,494
01113−160412	TNUA-160412						1,2	13,097
01113−220408	TNUA-220408		22,0	12,700	5,16		0,8	18,256
01113−220412	TNUA-220412						1,2	17,859
01113−220416	TNUA-220416						1,6	17,463
01113−220424	TNUA-220424						2,4	16,550
01113−270612	TNUA-270612		27,5	15,875	6.35 mm	6.35 mm	1,2	22,622
01113−270616	TNUA-270616						1,6	22,225
01113−270624	TNUA-270624						2,4	21,432

Continued


The marking plates of class M tolerance
digital	alphanumeric	Applica- the need*
01123−110304	TNMA-110304		11,0	6,350	2,26	3,18	0,4	9,128
01123−110308	TNMA-110308						0,8	8,731
01123−160308	TNMA-160308		16,5	9,525	3,81		0,8	13,494
01123−160312	TNMA-160312						1,2	13,097
01123−160404	TNMA-160404					4,76	0,4	13,897
01123−160408	TNMA-160408						0,8	13,494
01123−160412	TNMA-160412						1,2	13,097
01123−220408	TNMA-220408		22,0	12,700	5,16		0,8	18,256
01123−220412	TNMA-220412						1,2	17,859
01123−220416	TNMA-220416						1,6	17,463
01123−220424	TNMA-220424						2,4	16,550
01123−270612	TNMA-270612		27,5	15,875	6.35 mm	6.35 mm	1,2	22,622
01123−270616	TNMA-270616						1,6	22,225
01123−270624	TNMA-270624						2,4	21,432

________________
* See Appendix 3.

Continued


The marking plates of class G tolerance
digital	alphanumeric	Applica- the need*
-	-		11,0	6,350	2,26	3,18	0,4	9,128
-	-						0,8	8,731
-	-		16,5	9,525	3,81		0,8	13,494
-	-						1,2	13,097
-	-					4,76	0,4	13,897
01133−160408	TNGA-160408						0,8	13,494
01133−160412	TNGA-160412						1,2	13,097
01133−220408	TNGA-220408		22,0	12,700	5,16		0,8	18,256
01133−220412	TNGA-220412						1,2	17,859
01133−220416	TNGA-220416						1,6	17,463
-	-						2,4	16,550
-	-		27,5	15,875	6.35 mm	6.35 mm	1,2	22,622
01133−270616	TNGA-270616						1,6	22,225
-	-						2,4	21,432

_______________
* See Appendix 3.

Example of designation when ordering plates of solid alloy grade VK6-OM the class of admission U, with cutting edge length ГОСТ 19044-80 Пластины режущие сменные многогранные твердосплавные трехгранной формы с отверстием. Конструкция и размеры (с Изменениями N 1, 2) =16,5 mm, thickness =3.18 mm, radius =0,8 mm:

19 6516

0354 160308

3. Approximate weight plates specified in Appendix 1.

4. The notation of plates according to GOST 19042.

5. Technical requirements — GOST 19086.

6. Applicable grades listed in Appendix 2.

(Added, Rev. N 2).

ANNEX 1
Reference

Approximate weight plates


	Approximate weight of plates, g
Digital signage plates	carbide grades							from butwal- fromovich hard alloys	hard alloy with wear-resistant coating
	VK6-OM	VK6	VK8	ВК10 HOM	Т5К10	Т14К8	T15K6	КНТ16, ТН20	ВП3115	ВП3325
01113−110304	0,96	0,96	0,95	0,93	0,83	0,75	0,74	0,38	0,96	0,95
01123−110304
01113−110308	0,93	0,93	0,91	0,88	0,80	0,73	0,71	0,36	0,93	0,91
01123−110308
01113−160308	4,95	4,95	4,88	4,73	4,28	3,88	3,81	1,93	4,95	4,88
01123−160308
01113−160312	4,87	4,87	4,81	Of 4.66	4,21	3,82	3,75	1,90	4,87	4,81
01123−160312
01113−160404	Of 7.48	Of 7.48	Of 7.38	7,15	Of 6.47	5,86	5,76	Of 2.91	Of 7.48	Of 7.38
01123−160404
01113−160408	7,42	7,42	7,32	7,10	Of 6.41	Of 5.81	Of 5.71	2,89	7,42	7,32
01123−160408
01133−160408
01113−160412	7,29	7,29	7,19	Of 6.97	6,31	Of 5.71	Of 5.62	Of 2.84	7,29	7,19
01123−160412
01133−160412
01113−220408	13,20	13,20	13,00	Of 12.61	11,40	10,30	10,20	-	13,20	13,00
01123−220408
01133−220408
01113−220424	12,60	12,50	12,30	11,50	11,00	10,80	9,76	-	12,60	12,30
01123−220424
01113−220412	13,10	13,10	12,90	12,51	11,30	10,20	10,10	-	13,10	12,90
01123−220412
01133−220412
01113−220416	12,90	12,90	12,70	12,31	11,20	10,10	9,95	-	12,90	12,70
01123−220416
01133−220416
01113−270612	27,50	27,50	27,10	26,28	23,80	21,60	21,20	-	27,50	27,10
01123−270612
01113−270616	Of 27.30	Of 27.30	Of 26.90	26,09	23,60	21,40	21,00	-	Of 27.30	Of 26.90
01123−270616
01133−270616
01113−270624	27,10	27,10	Was 26.70	25,89	23,40	21,20	Of 20.80	-	27,10	Was 26.70
01123−270624

ANNEX 1. (Changed edition, Rev. N 2).

APPENDIX 2 (recommended). The use of grades of plates

ANNEX 2
Recommended


Digital signage plates	The main application	Additional application	Application by special order
01113−110304	-	N 3, N 7	N 1, N 2, N 4, N 5, N 6, N 8, N 9, N 10
01123−110304	-	-	N 1, N 2, N 3, N 4, N 5, N 6, N 7, N 8, N 9, N 10
01113−110308	-	-	N 1, N 2, N 3, N 4, N 5, N 6, N 7, N 8, N 9, N 10
01123−110308	N 3, N 7	N 1, N 2, N 4	N 5, N 6, N 8, N 9, N 10
01113−160308	N 3, N 9	-	N 1, N 2, N 4, N 5, N 6, N 7, N 8, N 10
01123−160308	-	-	N 1, N 2, N 3, N 4, N 5, N 6, N 7, N 8, N 9, N 10
01113−160312	N 3, N 4, N 9	-	N 1, N 2, N 5, N 6, N 7, N 8, N 10
01123−160312	-	-	N 1, N 2, N 3, N 4, N 5, N 6, N 7, N 8, N 9, N 10
01113−160404	-	-	N 1, N 2, N 3, N 4, N 5, N 6, N 7, N 8, N 9, N 10
01123−160404
01113−160408	N 9	N 3, N 7	N 1, N 2, N 4, N 5, N 6, N 8, N 9
01123−160408	N 3, N 9, N 10	N 1, N 2, N 7	N 4, N 5, N 6, N 8
01133−160408	-	-	N 1, N 2, N 3, N 4, N 5, N 6, N 7, N 8, N 9, N 10
01113−160412	-	-	N 1, N 2, N 3, N 4, N 5, N 6, N 7, N 8, N 9, N 10
01123−160412	N 1, N 3, N 9, N 10	N 2, N 7	N 4, N 5, N 6, N 8
01133−160412	-	-	N 1, N 2, N 3, N 4, N 5, N 6, N 7, N 8, N 9, N 10
01113−220408	N 9	-	N 1, N 2, N 3, N 4, N 5, N 6, N 7, N 8, N 10
01123−220408	-	N 10	N 1, N 2, N 3, N 4, N 5, N 6, N 7, N 9
01133−220408	-	-	N 1, N 2, N 3, N 4, N 5, N 6, N 7, N 9, N 10
01113−220424	-	-	N 1, N 2, N 3, N 4, N 5, N 6, N 7, N 9, N 10
01123−220424
01113−220412	N 9	-	N 1, N 2, N 3, N 4, N 5, N 6, N 7, N 10
01123−220412	-	N 7, N 10	N 1, N 2, N 3, N 4, N 5, N 6, N 7, N 9
01133−220412	-	-	N 1, N 2, N 3, N 4, N 5, N 6, N 7, N 9, N 10
01113−220416	-	-	N 1, N 2, N 3, N 4, N 5, N 6, N 7, N 9, N 10
01123−220416	-	N 3, N 7, N 10	N 1, N 2, N 4, N 5, N 6, N 9
01133−220416	N 5	-	N 1, N 2, N 3, N 4, N 6, N 7, N 9, N 10
01113−270612	-	-	N 1, N 2, N 3, N 4, N 5, N 6, N 7, N 9, N 10
01123−270612	-	N 7	N 1, N 2, N 3, N 4, N 5, N 6, N 9, N 10
01113−270616	N 5, N 7	N 6	N 1, N 2, N 3, N 4, N 9, N 10
01123−270616	-	-	N 1, N 2, N 3, N 4, N 5, N 6, N 7, N 9, N 10
01133−270616	-	-	N 1, N 2, N 3, N 4, N 5, N 6, N 7, N 9, N 10
01113−270624	-	-	N 1, N 2, N 3, N 4, N 5, N 6, N 7, N 9, N 10
01123−270624

N 1 — ВК10-HOM; N 2 — VK6-OM; N 3 — VK6; N 4 — VK8; N 5 — Т5К10; N 6 — Т14К8; N 7 — T15K6; N 8 — КНТ16; ТН20; N 9 — ВП3115; N 10 — ВП3325.

APPENDIX 3 (reference). The applicability of the plates

APPENDIX 3
Reference


	Marking	Plate without a chip breaking C-grooves
		the radius
		0,4	0,8	1,2	1,6	2,4
6.35 mm	TNMA 1103	++	++	+++	+++	+++
9,525	TNMA 1603	++	++	++	+++	+++
	TNMA 1604	+	+	+	++	+++
12,7	TNMA 2204	++	+	+	+	+++
15,875	TNMA 2706	+++	+++	++	++	++
19,05	TNMA 3309	+++	+++	+++	+++	++

Note. + — plates of the basic application, standardized.

++ — plates have limited use, not standardized.

+++ — plates are not recommended for use.

APP 2, 3. (Added, Rev. N 2).

GOST 19044-80

GOST 19044−80 cutting Inserts, replaceable carbide faceted triangular shape with a hole. The design and dimensions (with Amendments No. 1, 2)

APPENDIX 2 (recommended). The use of grades of plates

APPENDIX 3 (reference). The applicability of the plates

Metals and metal products

Our consultant will save your time

Subscription

GOST 19044-80

GOST 19044−80 cutting Inserts, replaceable carbide faceted triangular shape with a hole. The design and dimensions (with Amendments No. 1, 2)

APPENDIX 2 (recommended). The use of grades of plates

APPENDIX 3 (reference). The applicability of the plates

Payment ON-LINE

Metals and metal products

Our consultant will save your time

Subscription