GOST R 53197-2008
GOST R 53197−2008 (ISO 9202:1991) Jewelry. Samples of alloys based on precious metals
GOST R 53197−2008
(ISO 9209:1991)
Group W51
NATIONAL STANDARD OF THE RUSSIAN FEDERATION
Jewelry
SAMPLES OF ALLOYS BASED ON PRECIOUS METALS
Jewellery. Fineness of precious metal alloys
ISS 39.060
77.120.99
AXTU 1708
Date of introduction 2010−01−01
Preface
The objectives and principles of standardization in the Russian Federation established by the Federal law of 27 December 2002 N 184-FZ «On technical regulation», and rules for the application of national standards of the Russian Federation — GOST R 1.0−2004 «Standardization in the Russian Federation. The main provisions"
Data on standard
1 PREPARED AND SUBMITTED by the Technical Committee on standardization TC 304 «Noble metals, alloys, industrial and jewelry products made of them; secondary resources containing noble metals», Ekaterinburg factory on processing of nonferrous metals
2 APPROVED AND put INTO EFFECT by the Federal Agency for technical regulation and Metrology dated December 25, 2008 N 661-St
3 this standard is modified in relation to the international standard ISO 9202:1991 «Jewellery. The purity of the alloys based on precious metals» (ISO 9202:1991 «Jewellery — Fineness of precious metal alloys»). Additional words, phrases, indicators, their values are included in the text of the standard to reflect the needs of the national economy of the Russian Federation and/or the peculiarities of the Russian national standardization in italics.
In the introduction to this standard provides an explanation of the main changes made to the text.
4 INTRODUCED FOR THE FIRST TIME
Information about the changes to this standard is published in the annually issued reference index «National standards», and the text changes and amendments — in monthly indexes published information «National standards». In case of revision (replacement) or cancellation of this standard a notification will be published in a monthly information index «National standards». Relevant information, notification and lyrics are also posted in the information system of General use — on the official website of the Federal Agency for technical regulation and Metrology on the Internet
Introduction
In the text of this standard the following changes were made compared to the applied international standard:
— introduced additional sections: «Normative references» and «Methods of control»;
— section 4 (table 1) included all samples of the precious metals, established by the RF Government Decree dated
1 Scope
This standard specifies the samples of alloys based on precious metals (excluding solders) recommended for use in the manufacture of jewelry.
2 Normative references
_________________
* Name of item 2 in the original paper are shown in italics. — Note the manufacturer’s database.
This standard uses the regulatory references to the following standards:
GOST R 52599−2006** Precious metals and their alloys. General requirements for methods of analysis
_______________
* The designations and number of standards selected here and further in the text the sign «**", in the original paper are shown in italics (the rest in normal font). — Note the manufacturer’s database.
GOST 30649−99** Alloys based on noble metals for jewellery. Brand
Note — When using this standard appropriate to test the effect of reference standards in the information system of General use — on the official website of the Federal Agency for technical regulation and Metrology on the Internet or published annually by the information sign «National standards» published as on January 1 of the current year and related information published monthly indexes published in the current year. If the reference standard is replaced (changed), when using this standard should be guided by replacing (amended) standard. If the reference standard is cancelled without replacement, then the situation in which the given link applies to the extent that does not affect this link.
3 Terms and definitions
This standard applies the following term with the appropriate definition:
3.1 alloy (fineness): the Minimum content of precious metal measured in parts per thousand by weight of alloy.
4 Technical requirements
4.1 Set minimum value of samples. Tolerances in the direction of reduction is not allowed. Samples of alloys based on precious metals shall conform to the requirements of table 1.
Table 1 — Samples based on precious metals
Alloy of precious metal | Sample |
Alloy based on gold | 375 |
500 | |
585 | |
750 | |
958 | |
999 | |
999,9 | |
An alloy based on platinum | 850 |
900 | |
950 | |
990 | |
Alloy based on palladium | 500 |
850 | |
900 | |
950 | |
990 | |
Alloy based on silver | 800 |
830 | |
875 | |
925 | |
960 | |
999 |
4.2 Brand, chemical composition, properties of alloys based on precious metals recommendations for use (technological properties) for the samples shown in table 1, is given in GOST 30649**.
5 control Methods
_________________
* Name of item 5 in the original paper are shown in italics. — Note the manufacturer’s database.
5.1 Sample-based alloys of precious metals set by GOST R 52599**, GOST 30649**.
5.2 permitted to identify samples by other methods, certified in the prescribed manner and not inferior in accuracy to the standard.