GOST 2284-79

• gost-2284-79.pdf (501.04 KiB)
  ГОСТ 2284-79

GOST 2284−79 cold-rolled strips of carbon structural steel. Technical specifications (Changes No. 1−4)

GOST 2284−79
Group B34

INTERSTATE STANDARD

TAPE COLD-ROLLED CARBON
STRUCTURAL STEEL

Specifications

Cold rolled carbon structural steel strip. Specifications

OKP 12 3100

Date of introduction 1980−01−01

INFORMATION DATA

1. DEVELOPED AND INTRODUCED by the Ministry of ferrous metallurgy of the USSR

2. APPROVED AND promulgated by the Decree of the State Committee of standards of Ministerial Council of the USSR from 04.01.79 N 33

3. Standard corresponds to ISO 4960−86 in terms of mechanical properties for the tape of high quality and precision manufacturing for the tape advanced and high precision

4. REPLACE GOST 2284−69

5. REFERENCE NORMATIVE AND TECHNICAL DOCUMENTS

The designation of the reference document referenced	Item number
GOST 166−89	4.2
GOST 427−75	4.9
GOST 803−81	2.2
GOST 1050−88	2.2
GOST 1763−68	4.5
GOST 2789−73	2.10
GOST 2999−75	4.6
GOST 3282−74	5.1, 5.3
GOST 3560−73	5.1, 5.3
GOST 4381−87	4.2
GOST 6507−90	4.2
GOST 7566−94	3.1 a
GOST 8273−75	5.3
GOST 8828−89	5.3
GOST 9013−59	4.6
GOST 9347−74	4.7
GOST 9569−79	5.3
GOST 10354−82	5.3
GOST 10396−84	5.3
GOST 10877−76	5.2
GOST 11701−84	4.3
GOST 14019−80	4.4
GOST 14192−96	5.5
GOST 14959−79	2.2
GOST 15102−75	5.4
GOST 15150−69	5.7
GOST 15846−79	5.8
GOST 16272−79	5.3
GOST 18617−83	5.3
GOST 19300−86	4.1, 4.7
GOST 20435−75	5.4
GOST 20799−88	5.2
GOST 21650−76	5.4
GOST 22225−76	5.4
GOST 22536.0−87	4.12
GOST 22536.1−88	4.12
GOST 22536.2−87	4.12
GOST 22536.3−88	4.12
GOST 22536.4−88	4.12
GOST 22536.5−87	4.12
GOST 22536.6−88	4.12
GOST 22536.7−88	4.12
GOST 22536.8−87	4.12
GOST 22536.9−88	4.12
GOST 22536.10−88	4.12
GOST 22536.11−87	4.12
GOST 22536.12−88	4.12
GOST 24597−81	5.4
GOST 27809−95	4.12
GOST 29329−92	4.14
OST 38.01436−87	5.2
THAT 2−034−225−87	4.9

6. Limitation of actions taken by Protocol No. 5−94 of the Interstate Council for standardization, Metrology and certification (ICS 11−12−94)

7. EDITION with Amendments No. 1, 2, 3, 4, approved in November 1981, February 1986, August 1986, July 1990 (ICS 1−82, 5−86, 11−86, 11−90)


This standard applies to cold rolled strip of quality carbon structural steel, intended for manufacturing of details of machines and structures.

(Changed edition, Rev. N 3).

1. CLASSIFICATION AND ASSORTMENT

1.1. The tape is divided into:

for precision manufacturing

thickness:

normal accuracy

increased accuracy — T

high precision In

width:

normal accuracy

increased accuracy — sh;

in view of the surface

light With

bright with the colors of a tint — TS

dark;

by referring to edges

with cut edges

with mill edges — BUT;

by type of processing

annealed:

common quality

high quality OP

nagaremono:

common quality — N

high quality NP;

the permitted depth bezoperatsionnogo layer

group 1

group 2.

1.2. Tape made sizes

thickness: 0,10, 0,12, 0,15, 0,18, 0,20, 0,22, 0,25, 0,28, 0,30, 0,35, 0,40, 0,45, 0,50, 0,55, 0,60, 0,65, 0,70, 0,75, 0,80, 0,85, 0,90, 0,95, 1,00, 1,05, 1,10, 1,15, 1,20, 1,25, 1,30, 1,35, 1,40, 1,45, 1,50, 1,55, 1,60, 1,65; 1,70, 1,75, 1,80, 1,85, 1,90, 1,95, 2,00, 2,10, 2,20, 2,30, 2,40, 2,50, 2,60, 2,70, 2,80, 3,00, 3,10, 3,20, 3,40, 3,50, 3,60, 3,80, 4,00 mm;

width: 4, 5, 6, 8, 10, 12, 13, 14, 15, 16, 17, 18, 20, 22, 24, 25, 26, 28, 30, 32, 34, 35, 38, 40, 42, 45, 48, 50, 55, 60, 65, 70, 75, 80, 85, 90, 100, 105, 110, 120, 125, 130, 140, 150, 160, 170, 180, 190, 200, 210, 220, 230, 240, 250, 260, 270, 280, 290, 300, 310, 320, 330, 340, 350, 360, 370, 380, 390, 400, 410, 420, 430, 440, 450, 465 mm.

The width of the tape depending on the thickness of the tape shall be as defined in table.1.

Table 1

mm

The thickness of the strip	Tape width
From 0.10 to 0.28 incl.	4−120
SV. Of 0.28 «x 0.40 «	4−250
«And 0.40» to 0.45 «	5−250
«To 0.45» to 0.50 «	5−300
«Of 0.50» to 0.60 «	6−300
«Of 0.60» to 0.65 «	8−300
«To 0.65» to 0.80 «	8−465
«0,80» to 2.00 «	10−465
«2,00» 3,00 «	15−465
«3,00» 4,00 «	18−465

Note. Tape thickness greater than 2.00 mm with a width of 30 mm and a tape thickness greater than 3.00 mm for widths up to 40 mm are made by agreement with the consumer.


In agreement with the manufactured tape intermediate sizes in thickness and width with maximum deviation for the closest larger size.

1.1, 1.2. (Changed edition, Rev. N 4).

1.3. Maximum deviations in thickness of the tape shall be as specified in table.2.

Table 2

mm

The thickness of the strip	Maximum deviation in thickness of the tape-precision manufacturing
	normal	high	high
From 0.10 to 0.15 incl.	-0,02	-0,015	-0,010
SV. 0,15 «0,25 «	-0,03	-0,02	-0,015
«Of 0.25» to 0.40 «	-0,04	-0,03	-0,020
«0,40» 0,70 «	-0,05	-0,04	-0,025
«0,70» 0,95 «	-0,07	-0,05	-0,03
«0,95» 1,30 «	-0,09	-0,06	-0,04
«1,30» 1,70 «	-0,11	-0,08	-0,05
«1,70» 2,30 «	-0,13	-0,10	-0,06
«To 2.30» to 3.00 «	-0,16	-0,12	-0,08
«3,00» 4,00 «	-0,20	-0,16	-0,10

Notes:

1. Tape high accuracy in thickness is produced as agreed with the consumer.

2. By agreement between manufacturer and manufactured tape with double-sided (±) extreme deviations in thickness with preservation of tolerance.


(Changed edition, Rev. N 4).

1.4. Tolerances for the width of the tape shall be as specified in table.3.

Table 3

mm

The thickness of the strip	The ultimate deviation in the width of the tape
	for the cropped strip width								for uncut ribbon
	up to 100	over 100 to 300		over 300	up to 100	over 100 to 300		over 300	of the cropped strip width				of uncut tackle
	normal accuracy				increased accuracy				up to 100	over 100 up to 200	over 200 up to 300	over 300
From 0.10 to 0.63 incl.	-0,3	-0,4	-0,5		-0,2	-0,3	-0,4		+3	+4	+5	+6	+4% of nominal width
SV. 0,63 «1,00 «	-0,4	-0,5	-0,6		-0,3	-0,4	-0,5
«To 1.00» to 4.00 «	-0,6	-0,7	-0,8		-0,4	-0,5	-0,6

Note. By agreement between manufacturer and manufactured tape with double-sided (±) limit deviations on width preserving tolerance.


Examples of symbols:

Ribbon of steel grade 50, high accuracy on thickness and width, light, with cut edges, nagarebana ordinary quality, sizes 0,5x20 mm:

Band 50-SH-C-H-0,5x20 GOST 2284−79

Ribbon of steel grade 45, high accuracy on thickness, normal accuracy in width, bright with cut edges, annealed ordinary quality, 1 group decarburization, size 2,0x30 mm:

Tape 45-T-s-1−2x30 GOST 2284−79

Ribbon of steel grade 45, high accuracy on thickness and width, light, with cut edges, nagarebana high quality sizes 0,7x50 mm:

Tape 45-TSH-With-NP-0,7x50 GOST 2284−79

(Changed edition, Rev. N 4).

2. TECHNICAL REQUIREMENTS

2.1. Cold-rolled strip of quality carbon steel shall be manufactured in accordance with the requirements of this standard for technological regulations approved in the prescribed manner.

(Changed edition, Rev. N 2).

2.2. The tape shall be manufactured of steel grades 15, 15ps, 20, 20ps, 25, 30, 35, 40, 45, 50, 55, 60 according to GOST 1050, brands 65, 70 according to GOST 14959 and brand 18JUA according to GOST 803.

2.3. Mechanical properties of annealed and work-hardened strips of ordinary quality shall be as given in table.4.

Table 4

Steel grade	Tensile strength , N/mm(kgf/mm)	Elongation , %, not less than	Tensile strength , N/mm(kgf/mm)
	Ribbon annealed		Tape nagarebana
15, 15ps, 20, 20ps,	310−490 (32−50)	20	440−780 (45−80)
18JUA	310−540 (32−55)	18	490−830 (50−85)
25	340−590 (35−60)	18	540−880 (55−90)
30, 35	390−640 (40−65)	16	640−930 (65−95)
40, 45	440−690 (45−70)	14	690−1030 (70−105)
50, 55	440−740 (45−75)	13	740−1080 (75−110)
60, 65, 70	440−740 (45−75)	10	740−1130 (75−115)

2.2, 2.3. (Changed edition, Rev. N 4).

2.3. The mechanical properties of ribbons annealed high quality (OD) of 25−70 steel grades shall be as given in table.4A.

Table 4A

Steel grade	Temporary resistance , N/mm(kgf/mm)	Elongation , %, not less
25	340−540 (35−55)	18
30, 35	390−590 (40−60)	16
40, 45	440−600 (45−61)	14
50, 55	440−610 (45−62)	13
60	440−620 (45−63)	12
65	440−630 (45−64)	11
70	440−640 (45−65)	10

2.3 b. Tape nagarebana enhanced (NP) must be manufactured with the runway strength, are given in table.4, in the party, not more than:

150 N/mm(15 kgf/mm) — for tape up to a thickness of 0.36 mm incl.;

180 N/mm(18 kgf/mm) for tapes with a thickness St of 0.36 to 1.00 mm incl.;

200 N/mm(20 kgf/mm) for tapes with a thickness of 1.00 mm. St

By agreement with the consumer allowed to set a specific range of values of the interim resistance taking into account the above permissible values of run-up.

2.3 a and 2.3 b. (Added, Rev. N 4).

2.4, 2.5. (Deleted, Rev. N 3).

2.6. At the request of the consumer annealed tape shall withstand a bend test 180° transverse or 90° to the direction of rolling on the mandrel with a radius equal to the thickness of the tape; in the bend must not have any cracks and delamination.

2.7. In the annealed ribbon of steel grades 40, 45, 50, 55, 60, 65, 70 unilateral total depth of decarburization shall not exceed the limits specified in table.6.

Table 6*

________________
* Table 5. (Deleted, Rev. N 3).

mm

The thickness of the strip	The permissible depth of decarburization
	group 1	group 2
0.5 incl.	0,02	0,05
SV. 0,5 «1,0	0,04	0,10
«1,0» 2,0	0,06	0,15
«2,0» 4,0	0,08	0,20

(Changed edition, Rev. N2).

The depth bezoperatsionnogo layer is adopted the zone of complete decarburization (ferrite) + transition zone.

At the request of the consumer nagaremono the ribbon of steel grades 40, 45, 50, 55, 60, 65, 70 made with depth control bezoperatsionnogo layer in accordance with the standards specified in table.6.

2.8. Light tape should have a surface of metallic color from light gray to dark gray shades.

The bright ribbon with the colors of tint allowed the oxidized surface with non-uniform colors or different shades.

The surface color is dark ribbon is not regulated. On the surface of the tape allowed the dark stains of pollution.

2.9. On the surface of the tape should not be captured, katanoi scale, okatannyh metal particles, rips and rust. Allowed a single prisoner, as well as a separate small longitudinal scratches, scratches, fingerprints, rabini, the value of which does not exceed:

for bright and bright with flowers or ribbon — half of the limit deviations on thickness;

for the dark strip — tolerances for thickness.

2.8, 2.9. (Changed edition, Rev. N 4).

2.10. The roughness parameter of the surface of the light strip should not be more than 1.25 µm according to GOST 2789.

At the request of the consumer, the tape can be produced with a roughness parameter of not more than 0,32 µm according to GOST 2789 with the depth of defect not exceeding the maximum deviations in thickness of the tape.

2.11. On the cut tape are not allowed ragged edge and notch depth of more than half of the limit deviations on width and burrs — more maximum deviations in thickness of the tape.

(Changed edition, Rev. N 4).

2.12. On the uncut tape is not allowed on the ragged edge with a depth of more than half of the limit deviations on width and burrs — more tolerances for the width of the tape.

(Changed edition, Rev. N 1).

2.13. Cropped tape is manufactured with a camber not exceeding 1 m length:

5 mm for tape widths from 10 to 18 mm incl.,

4 mm — for tapes with a width of over 18 to 25 mm cyl.,

3 mm for belt width 25 St to 50 mm incl.,

2 mm — for tapes of width over 50 mm.

By agreement between manufacturer and consumer clipped the tape is manufactured with a camber not exceeding 1 m length:

6 mm — for belt width from 10 to 40 mm incl.,

2.5 mm — for tapes with a width of over 40 mm.

Tape width less than 10 mm from the regulated rate for camber is made by agreement between manufacturer and consumer.

(Changed edition, Rev. N 4).

2.14. Tape shall be manufactured in coils with inner diameter from 200 to 850 mm.

The rolls should be tight and smooth winding operation.

Changing the shape of the coil, leading to a fixed (residual) deflection in the position to supply more than 15% of the inner diameter is not allowed.

(Changed edition, Rev. N 2).

2.15. Tape with a thickness of 1 mm or more can be supplied upon agreement with the consumer in the form of strips, tied in bundles. The length of individual strips in a bundle must be from 2 to 3 m.

Delivery cropped strips the length from 1 to 2 m in amount of not exceeding 20% of the party.

2.16. The minimum mass of the coil is:

strips of 80 mm or less at the rate of at least 0.5 kg per 1 mm of width;

for tape widths over 80 mm — not less than 40 kg.

The minimum mass of the coil in the reference application.

In coordination with the consumer the maximum bale weight should not exceed 80 kg.

(Changed edition, Rev. N 1, 2).

2.17. The coil should consist of one segment. Allowed the rolls of strips, consisting of two strands in an amount not exceeding 10% of the party. Place of winding should be checked.

It is not allowed to overlap welding and other ways of connecting the tape segments per roll.

If the edges of the belt 3−4 isolated defects, value of the established claim 2.11, allowed by agreement with the consumer not to cut from a roll of defective parts subject to delivery to the consumer of additional quantity of tape (based on each defect 1 m length). Locations of defects must be marked with paint, gaskets or other means.

(Changed edition, Rev. N 2, 4).

2.18. Striping tapes is not allowed.

(Added, Rev. N 1).

3. ACCEPTANCE RULES

3.1. Rules of acceptance GOST 7566.

(Added, Rev. N 4).

3.1. Tape is accepted by the parties. The party should consist of strips of the same steel grade, same bottoms, same size, one group of precision manufacturing, one type of surface and edges, one treatment, one group of decarburization and be accompanied by a document about quality that contains:

trademark or the name and trademark of manufacturer;

the symbol of the tape;

the number of melt showing the results plotnogo chemical analysis;

the results of the tests;

the number of coils, packs (packs) or of packages in the shipment;

the weight of the party.

By agreement with a consumer party may consist of strips of two different heats of the same brand.

(Changed edition, Rev. N 2).

3.2. To check sizes, quality of the surface and the edges of the belt taken away 5% of rolls or packs of tapes, but at least two rolls or packs from the party.

3.3. From party tape, tested according to claim 3.2, should be selected:

to test a temporary resistance, relative elongation, bezoperatsionnogo depth of layer or hardness tempered piece of the tape, camber, delamination, roughness, flatness and chemical composition (if necessary), bending test, 1 roll from the party weighing up to 25 tons or 2 rolls from the party weighing over 25 tons.

3.2, 3.3. (Changed edition, Rev. N 4).

3.4. If unsatisfactory test results of at least one of the indicators it is carried out re-tests on twice the number of rolls of the number not being tested.

The results of repeated tests apply to the entire party.

4. TEST METHODS

4.1. The quality of the surface and the edges of the belt checked visually without the use of magnifying devices. Quality control of surfaces and edges carried out on the 2−5 coil of the roll.

If necessary, the amount of surface defects should be determine with the help of profiling-profilers according to GOST 19300 and other means of measuring the respective accuracy of normative-technical documentation.

To test a temporary resistance, relative elongation, bezoperatsionnogo depth of layer or hardness tempered piece of the tape, camber, delamination, roughness parameters of the surface, flatness and chemical composition (if necessary) for the Flexural testing of each selected according to claim 3.3 rolls or packs of cut one sample for each test.

4.2. Tape dimensions and size of defects on the edges of the belt must be checked with micrometers GOST 6507, 4381 GOST, GOST 166 calipers and other measuring instruments of appropriate accuracy according to normative-technical documentation.

The measurement of the thickness of the tape with a cut edge width of 20 mm and less hold in the middle of its width, of a width exceeding 20 mm — not less than 10 mm from the edge.

The thickness of the strip with mill edges measured at a distance of not less than 20 mm from the edge.

4.1, 4.2. (Changed edition, Rev. N 4).

4.3. Tensile test on strips of thickness less than 3.00 mm carried out on samples of type I or type II according to GOST 11701. Allowed the test tape with a thickness of 1.7 mm and less spending on samples with an initial estimated length of 80 mm and a width of 20 mm.

Tape of thickness 3.0 mm and over shall be tested on samples with an initial estimated length of 80 mm and a width of 20 mm.

Preparation of samples for the tests — according to GOST 11701.

Allowed test strips with a width of less than 20 mm carried out on samples having a width equal to the width of the manufactured belt, with the initial design length of a specimen where the width of the tape made.

Samples for test cut out along the direction of rolling.

(Changed edition, Rev. N 2, 4).

4.4. Test strips for bending is carried out according to GOST 14019*.
______________
* On the territory of the Russian Federation GOST 14019−2003. — Note the manufacturer’s database.

4.5. Depth bezoperatsionnogo tape layer is determined according to GOST 1763.

In coordination with the consumer checking for decarburization may be replaced by hardness tempered piece of the tape according to Rockwell or Vickers. Standards of hardness and tempering shall be established in consultation with the consumer.

The choice of zoom metallographic method should provide accuracy of depth determination bezoperatsionnogo layer.

(Changed edition, Rev. N 4).

4.6. Determination of the Rockwell hardness is carried out according to GOST 9013, Vickers — GOST 2999.

4.7. The parameters of surface roughness of the tape should be determined by profiling-profilers according to GOST 19300−86, microinterferometers according to GOST 9347 and other measuring instruments of appropriate accuracy.

(Changed edition, Rev. N 4).

4.8. Striping tapes reveal by visual inspection of the edges of the tape or with the use of a magnifying glass zoom 7and when you test it in tension. If necessary in doubtful cases to detect stratification is applied hot etched macrosections of 50% aqueous solution of hydrochloric acid with a temperature of 60−80 °C for 10 min.

4.9. Camber shall be checked by combining the edges of the sample tape with a length of 1 m with a straight line. The measurement is performed in the place of the greatest curvature of the ruler according to GOST 427, a set of probes on the other 2−034−225 and other means of measurement corresponding to the accuracy in the normative-technical documentation.

(Changed edition, Rev. N 4).

4.10. Measurement of the flatness of the tape is carried out according to the method agreed between the manufacturer and the customer.

At the request of the consumer cropped tape is made with a regulated amount of flatness according to standards set by agreement with the consumer.

4.11. The amount of residual deflection coils is determined by the ratio of the difference between the maximum and minimum values of the inner diameter of the coil to its rated value, expressed in percent.

The measurement of the internal diameter of the coils is made by any means of measurement with an accuracy of up to 1 mm.

4.12. The chemical composition of the metal tape is certified by a document of quality of the manufacturer of the metal. If necessary, the chemical composition of the metal strip is determined according to GOST 22536.0 to GOST 22536.12, GOST 27809.

(Changed edition, Rev. N 4).

4.13. Allowed to use non-destructive methods of control of mechanical properties and other characteristics specified according to coordinated methods.

4.14. Weighing of packages in the party, and if necessary, the rolls must be performed at the weights according to GOST 29329, or other scales, providing weighing errors to 1%.

(Added, Rev. N 4).

5. PACKING, MARKING, TRANSPORTATION AND STORAGE

5.1. Each roll or bundle (package) of the ribbon should be tied in at least three places soft metal ribbon or wire according to GOST 3560, GOST 3282 or other regulatory-technical documentation.

Allowed other ways of fastening the coils to ensure the density of the winding and secure clamping of the ends of the tape and dimensional stability of the rolls during transportation. When securing the ends of the coil are spot welded, the depth of penetration should not exceed two thicknesses of tape.

At the request of the consumer the ends of the rolls of tape with a width of 30 mm or more spot-welds are not fixed.

(Changed edition, Rev. N 1, 2, 4).

5.2. The tape should be coated with a thin layer of inhibited lubrication, which protects the tape against corrosion, a mixture of GSD and oil-12A And I-20 according to GOST 20799 in the ratio of 1:1 mixture of NG-203A for OST 38.01436, and oil AND-or 18A-20A ratio 1:1, 17 10877 churchyard and other types of lubricants and ratio of the components of lubricants, providing corrosion protection.

5.3. The rolls of tape of thickness 0.25 mm and less shall be wrapped with a layer of paper and Packed in wooden boxes type II according to GOST 18617 or other normative and technical documentation, tins, containers according to normative-technical documentation.

Tape thickness 0.25 mm pack:

during transportation on pallets made according to normative-technical documentation, the rolls placed one way:

on wooden or metal pallets in the stack (package) weight up to 1.25 T. the Coil or stack of coils should be wrapped in paper and attached to the pallet «under lock and key» at least three metal strips according to GOST 3560, or other regulatory-technical documentation.

Permitted to attach the roll or stack of rolls to the pallet with a soft metal wire according to GOST 3282 or other normative and technical documentation:

on wooden or metal pallets in the stack (packets) weighing up to 6 t, the lower roll of the foot is wrapped in paper or tape. The foot is attached to the pallet «under lock and key» at least three metal strips according to GOST 3560, or other regulatory-technical documentation. Additionally, bypassing the sump, stop the fourth tied off with a ribbon hanging metal label. The foot is wrapped with paper, and then non-conforming a metal sheet or a sheet obtained by welding of non-conforming sheets or ribbons, and tied off by forming a single metal band «under the castle». Top foot cover metal cover manufactured from substandard sheet or tape and having a circular shape with curved petals with the size not less than 50 mm, and tied with «under the castle» on the petals one by a metal band. Packed foot tied with «under the castle» with two mutually perpendicular metal strips, one of which is attached a metal marking label.

Change the packaging while ensuring quality packaging and security tape.

In coordination with the consumer the mass of the foot shall not exceed 5 tonnes;

during transportation without pallets coils, bundles (packs) the tape must be wrapped with a layer of paper, then a layer of polymeric film or fabric and stitched soft metal ribbon or wire according to GOST 3560, GOST 3282 or other normative and technical documentation in at least three places or by another method ensuring the safety of the package.

Mechanized method of packing the tape pack in one of the following ways:

the rolls of tape must be wrapped with a layer of paper according to GOST 10396 or other crepe paper according to normative-technical documentation, equal in protective properties;

the rolls of tape must be covered with a removable inhibited polymer coating according to normative-technical documentation;

the rolls of tape must be wrapped waste metal strip. Packing is fixed by welding around the perimeter of the coil;

the rolls of tape must be wrapped with a layer of paper and fabric.

The packaging method chosen by the manufacturer. In coordination with the consumer the ribbon more than 0.25 mm is not allowed to pack.

Tape thickness 0.25 mm and less can be transported on pallets.

The quality of packaging materials used:

the waxed paper according to GOST 9569*;
______________
* On the territory of the Russian Federation GOST 9569−2006. — Note the manufacturer’s database.

paper double-layered wrapping according to GOST 8828;

the waxed paper according to GOST 8273 and the other on the normative and technical documentation;

the polymeric film according to GOST 10354, 16272 GOST and other normative and technical documentation;

container holstoproshivny the canvas according to normative-technical documentation;

other types of packaging materials according to normative-technical documentation, with the exception of cotton and linen fabrics and also stitched the flap of the waste of the textile industry.

(Changed edition, Rev. N 1, 2, 4).

5.4. The tape is transported by all kinds of transport in covered vehicles in accordance with cargo carriage regulations applicable to transport of this form, and in transportation by railway in conformity with the technical conditions of loading and fastening of cargoes, approved by the Ministry of Railways of the USSR.

Consolidation packages in overpacks must be carried out according to GOST 21650, GOST 24597.

Transportation of tape packages weighing up to 6 tons in metal packaging is carried out in open vehicles.

Allowed the transport of the tape in universal containers according to GOST 15102,20435 GOST, GOST 22225.

(Changed edition, Rev. N 4).

5.5. To each roll, bundle (package) or cargo should be attached label, which indicate:

trademark or the name and trademark of manufacturer;

the room melt;

the symbol of the tape;

batch number.

(Changed edition, Rev. N 2).

5.5. Transport marking under GOST 14192.

(Added, Rev. N 2).

5.6. (Deleted, Rev. N 2).

5.7. Store the tapes must conform to the conditions 2 GOST 15150.

(Changed edition, Rev. N 4).

5.8. The tape is sent to the far North and equivalent areas, shall be Packed in accordance with the requirements of GOST 15846* and of this standard.
______________
* On the territory of the Russian GOST Federalization 15846−2002. — Note the manufacturer’s database.

(Added, Rev. N 4).

APP (reference)

APP
Reference

Tape width, mm	The minimum weight of roll, kg
4	2,0
5	2,5
6	3,0
8	4,0
10	5,0
12	6,0
13	6,5
14	7,0
15	7,5
16	8,0
17	8,5
18	9,0
20	10,0
22	11,0
24	12,0
25	12,5
26	13,0
28	14,0
30	15,0
32	16,0
34	17,0
35	17,5
38	19,0
40	20,0
42	21,0
45	22,5
48	24,0
50	25,0
55	27,5
60	30,0
65	32,5
70	35,0
75	37,5
80 or more	40,0

APP. (Added, Rev. N 2).