GOST R 54564-2011

• gost-r-54564-2011.pdf (1.16 MiB)
  ГОСТ Р 54564-2011

GOST R 54564−2011 Scrap and wastes of nonferrous metals and alloys. General specifications

GOST R 54564−2011

Group В57

NATIONAL STANDARD OF THE RUSSIAN FEDERATION

SCRAP AND WASTES OF NONFERROUS METALS AND ALLOYS

General specifications

Non-ferrous metals and alloys scrap and waste. General specifications

OKS 77.120.01
GST 17 8110

Date of introduction 2013−01−01

Preface

1 DEVELOPED by non-profit partnership «interregional center of secondary non-ferrous metallurgy"

2 SUBMITTED by the Technical Committee for standardization TC 462 «Secondary nonferrous metals"

3 APPROVED AND put INTO EFFECT by the Federal Agency for technical regulation and Metrology dated 29 November 2011 No. 648-St

4 INTRODUCED FOR THE FIRST TIME


Application rules of this standard are established in GOST R 1.0−2012 (section 8). Information about the changes to this standard is published in the annual (as of January 1 of the current year) reference index «National standards» and the official text changes and amendments — in monthly information index «National standards». In case of revision (replacement) or cancellation of this standard a notification will be published in the upcoming issue of the monthly information index «National standards». Relevant information, notification and lyrics are also posted in the information system of General use — on the official website of the Federal Agency for technical regulation and Metrology on the Internet (gost.ru)

1 Scope

This standard applies to scrap and wastes of nonferrous metals and alloys intended for the production of non-ferrous metals and their alloys and other products.

2 Normative references

This standard uses the regulatory references to the following standards:

GOST R 8.563−2009 State system for ensuring the uniformity of measurements. Techniques (methods) of measurements

GOST R 12.4.026−2001 System of standards of occupational safety. Signal colours, safety signs and signal marking. The purpose and rules of application. General technical requirements and characteristics. Test methods

GOST R 12.4.191−2011 (EN 149:2001+A1:2009) standards System of labor safety. Means of individual protection of respiratory organs. Filtering half masks to protect against aerosols. General specifications

GOST R 12.4.230.1−2007 (EN 166−2002) System of occupational safety standards. Personal protective equipment eye. General technical requirements

GOST R 51232−98 drinking Water. General requirements to organization and methods of quality control

GOST R 51321.1−2007 (IEC 60439−1:2004)low voltage complete Devices distribution and control. Part 1. The devices tested in full or in part. General technical requirements and test methods

GOST R 53361−2009 Bags of paper and composite materials. General specifications

GOST R 54565−2011 Scrap and wastes of nonferrous metals and alloys. Terms and definitions

GOST 12.1.004−91 System safety standards. Fire safety. General requirements

GOST 12.1.005−88 standards System of labor safety. General hygiene requirements for working zone air

GOST 12.1.007−76 System of standards of occupational safety. Harmful substances. Classification and General safety requirements

GOST 12.1.010−76 System of standards of occupational safety. No danger of explosion. General requirements

GOST 12.1.016−79 System of standards of occupational safety. The air of the working area. Requirements for measurement techniques of concentrations of harmful substances

GOST 12.2.007.0−75 System safety standards. Products electrical. General safety requirements

GOST 12.2.007.1−75 System safety standards. Rotating electrical machines. Safety requirements

GOST 12.2.007.2−75 System safety standards. Power transformers and reactors electrical. Safety requirements

GOST 12.2.007.3−75 System safety standards. Electrical devices for voltages above 1000 V. safety Requirements

GOST 12.2.007.4−75 System safety standards. Cabinets of complete distribution devices and complete transformer substations, the collecting chambers of unilateral service, the cell is sealed gas-insulated switchgear

GOST 12.2.007.5−75 System safety standards. The power capacitors. Install the condenser. Safety requirements

GOST 12.2.007.6−75 System safety standards. The low-voltage switching devices. Safety requirements

GOST 12.2.007.8−75 System safety standards. The device welding and for plasma processing. Safety requirements

GOST 12.2.007.9.8−89 (IEC 519−8-85) System of occupational safety standards. Electrothermal equipment. Furnace electroslag remelting. Safety requirements

GOST 12.2.007.10−87 standards System of labor safety. Installations, generators and induction heaters for electrothermics, plant and ultrasonic generators. Safety requirements

GOST 12.2.007.11−75 System safety standards. Converters of electric power semiconductor. Safety requirements

GOST 12.2.007.12−88 standards System of labor safety. The current sources of the chemical. Safety requirements

GOST 12.2.007.13−2000 System of standards of occupational safety. Electric lamps. Safety requirements

GOST 12.2.007.14−75 System safety standards. Cables and cable fittings. Safety requirements

GOST 12.2.009−99 Metalworking. General safety requirements

GOST 12.3.002−75 System safety standards. The process of production. General safety requirements

GOST 12.3.009−76 System of standards of occupational safety. The work of loading and unloading. General safety requirements

GOST 12.4.004−74 gas filtering Respirators RPG-67. Specifications

12.4.009 GOST-83 System of standards of occupational safety. Fire fighting equipment for protection of objects. Principal. The accommodation and service

GOST 12.4.010−75 System safety standards. Personal protective equipment. Mittens special. Specifications

GOST 12.4.021−75 System safety standards. System ventilation. General requirements

GOST 12.4.028−76 System of standards of occupational safety. Respirators SB-1 «Petal». Specifications

GOST 12.4.029−76 System of standards of occupational safety. Aprons special. Specifications

GOST 12.4.068−79 System of standards of occupational safety. PPE dermatological. Classification and General requirements

GOST 17.2.3.02−78 Protection of nature. Atmosphere. Rules for establishing permissible emissions of harmful substances by industrial enterprises

GOST 123−2008 Cobalt. Specifications

GOST 492−2006 Nickel, Nickel alloys, and copper-Nickel, processed by pressure. Brand

GOST 614−97 casting Bronzes in pigs. Specifications

GOST 804−93 primary Magnesium ingots. Specifications

GOST 859−2001 Copper. Brand

GOST 860−75 Tin. Specifications

GOST 1020−97 casting of Brass ingots. Specifications

GOST 1292−81 Alloys lead-armenistis. Specifications

GOST 1320−74 (ISO 4383−91) Babbit tin and lead. Specifications

GOST 1583−93 Alloys aluminum casting. Specifications

GOST 2171−90 Parts, products, semi-finished products and billets of non-ferrous metals and alloys. Marking stamps

GOST 2856−79 Alloys magnesium casting. Brand

GOST 2991−85 wooden disposable Boxes for loads up to 500 kg. General specifications

GOST 3640−94 Zinc. Specifications

GOST 3778−98 Lead. Specifications

GOST 4388−72 drinking Water. Methods for determination of mass concentration of copper

GOST 4658−73 Mercury. Specifications

GOST 4784−97 Aluminum and aluminum deformable alloys. Brand

GOST 5017−2006 Bronze tin pressure treated. Brand

GOST 5959−80 Boxes made of wood-based panels for non-separable loads weighing up to 200 kg. General specifications

GOST 6247−79 steel welded Barrels with hoops of skiing on the body. Specifications

GOST 10354−82 polyethylene Film. Specifications

GOST 14113−78 aluminium antifriction Alloys. Brand

GOST 14192−96 Marking of cargo

GOST 14957−76 Alloys magnesium wrought. Brand

GOST 15527−2004 Alloys copper-zinc (brass) pressure treated. Brand

GOST 17366−80 steel welded thick-walled Barrels for chemical products. Specifications

GOST 17811−78 polyethylene Bags for chemical products. Specifications

GOST 18165−89 drinking Water. Method for the determination of the mass concentration of aluminium

GOST 18175−78 of Bronze without tin pressure treated. Brand

GOST 18293−72 drinking Water. Methods of determination of lead, zinc, silver

GOST 18308−72 drinking Water. Method for the determination of molybdenum content

GOST 18477−79 Containers are universal. The types, basic parameters and dimensions

GOST 19241−80 Nickel and alloyed Nickel alloys treated under pressure. Brand

GOST 19433−88 dangerous Cargo. Classification and marking

GOST 19807−91 Titanium and titanium wrought alloys. Brand

GOST 21130−75 electrical Products. Clamps earthing and grounding. The design and dimensions

GOST 24231−80 non-ferrous metals and alloys. General requirements to selection and preparation of samples for chemical analysis

GOST 26653−90 Preparation of General cargoes for transportation. General requirements

GOST 28053−89 Shavings of non-ferrous metals and alloys. Methods of sampling, sample preparation and test methods

GOST 28192−89 Wastes of nonferrous metals and alloys. Methods of sampling, sample preparation and test methods

GOST 29103−91 Tungsten, molybdenum. General requirements for methods of chemical and spectral analysis

Note — When using this standard appropriate to test the effect of reference standards information system of General use — on the official website of the Federal Agency for technical regulation and Metrology on the Internet or in the annual information index «National standards» published as on January 1 of the current year, and the editions of the monthly information index «National standards» for the current year. If replaced with a reference standard, which was given an undated reference, then it is recommended to use the current version of this standard, taking into account all enabled in this version modifications. If replaced with a reference standard, which is given a dated reference, it is recommended to use the version of this standard referred to above by year of approval (acceptance). If after approval of this standard in the reference standard, which is given a dated reference, a change affecting a provision to which reference, the provision is recommended to be applied without taking into account this change. If the reference standard is cancelled without replacement, the position in which reference is made to him, recommended to be used in part not affecting this link.

3 Terms and definitions

This standard applies the terminology according to GOST R 54565.

4 Classification

4.1 waste and Scrap of non-ferrous metals and alloys are classified by the metals, their physical properties and chemical composition into groups in accordance with table 1.


Table 1

Name of scrap and waste of non-ferrous metals	Group
Aluminum and aluminum alloys	A1-A38
Tungsten, tungsten chemicals, tungsten alloys	B1-B17
Cadmium and cadmium alloys	Кд1-Kd2
Cobalt and its compounds and alloys	1-Ко3
Magnesium and magnesium alloys	Мг1-Мг7
Copper	M1-M13
Brass	L1-Л22
Bronze	Probes Unit 1-Бр14
Molybdenum, molybdenum chemical compounds and alloys	Мо1-Мо9
Nickel and Nickel alloys	H1-H10
Tin and tin-lead alloys	O1-O10
Mercury and its compounds	P1-P6
Lead and lead alloys	C1-C17
Titanium and titanium alloys	T1-T7
Zinc and zinc alloys	C1-Ц12
Scrap difficult	Сл1-Сл7
Bimetals	БМ1-BM6

5 Technical requirements

5.1 Characteristics of scrap and waste of nonferrous metals and alloys and their technical requirements groups should correspond to those in tables 2−18.


Table 2 — Aluminium and its alloys

Group	Characteristic of the group	Figure	The norm
A1	Clean waste from unalloyed aluminium from the production of rolled profiles, tubes, sheets, tapes, etc. Brand: A85, A8, A7, A7E, A6, A5, A0, AD00 (1070А), AD0 (1050А), AD1, AD (1200)	Metal content by mass, %, not less	98
		The contamination harmless impurities, by mass, %, not more	2
		A contamination with iron	Not allowed
		Thickness, mm, not less	1
A2	Scrap of non-alloy aluminium: electrical products — wire, bare conductor of cables and cords, tires switchgear, transformers, rectifiers, heat exchangers of refrigerators. Brand: A85, A8, A7, A7E, A6, A5, A0, AD00 (1070А), AD0 (1050А), AD1, AD (1200)	Metal content by mass, %, not less	97
		The contamination harmless impurities, by mass, %, not more	3
		including iron, %, not more	2
A3	The scrap foil from unalloyed aluminium: food foil, packing tape without the anodized foil, without condenser foil without paper, plastic and other materials. Brand: A85, A8, A7, A6, A5, AD00 (1070А), AD0 (1050А), AD1	Metal content by mass, %, not less	97
		The contamination harmless impurities, by mass, %, not more	3
		A contamination with iron	Not allowed
		Thickness, mm, not more	1
		Hydraulically pressed material is supplied by agreement between the buyer and seller
A4	Pure waste of aluminum alloy with low copper content in the form of sheets, trim profiles. Brand: AD31 (6063), AD33 (6061), AD35 (6082), D12, AMG1 (5005), MM (3005), AMC (Al 3003), AB, А154	Metal content by mass, %, not less	98
		The contamination harmless impurities, by mass, %, not more	2
		A contamination with iron	Not allowed
A5	Scrap aluminium alloys with a low content of copper: consumer goods — kitchenware, household electrical appliances, sports equipment, furniture, structural elements — roofing material, cladding of houses, window frames, walls, escalators. Brand: AD31 (6063), AD33 (6061), AD35 (6082), D12, AMG1 (5005), MM (3005), AMC (Al 3003), AB, А154	Metal content by mass, %, not less	97
		The contamination harmless impurities, by mass, %, not more	3
		including:
		iron	2
		oil	1
		The sizes of pieces in one dimension, mm, not more	1000
		Without the presence of blinds, foil, wire, food molds, airplane sheet, bottle caps, etc.
A6	Waste aluminum rolling low zinc and high copper content: wire, sheets, strips, etc. Brands: D1 (2017), D18 (2117), D19, B65, AK6, AK8 (2014)	Metal content by mass, %, not less	98
		The zinc content by mass, %, not more	0,3
		The contamination harmless impurities, by mass, %, not more	2
		including iron, %, not more	Not allowed
A7	Scrap aluminium rolled products and extrusions with low zinc content: the chassis, the blades of the propellers, a frames, panels, trim, wings and fuselage of the aircraft; drill pipe, drilling equipment units; the wheels of cars, consumer goods (folding chairs, chairs, tables). Brands: D1 (2017), D16 (2024), D18 (2117), D19, B65, AK6, AK8 (2014)	Metal content by mass, %, not less	97
		The contamination harmless impurities, by mass, %, not more	3
		including iron, %, not more Scrap that does not meet the requirements of this kind, comes by agreement between buyer and seller	2
A8	Waste aluminum rolling and casting with a high content of magnesium. Brand: Amg2 (5251), Amg3, Amg4 (5086), AMg5, AMg6, АМг61, АЛ8, АЛ13, АЛ23, АЛ27, АЛ28, АЛ29	Metal content by mass, %, not less	98
		The contamination harmless impurities, by mass, %, not more	2
		including iron, %, not more	Not allowed
A9	Scrap aluminum rolled products and castings with high magnesium content: welded tank, working under pressure; pipelines for fresh water, oil and fuel systems; television and rigs; transportation equipment; housing and parts of missiles; the details of ship machinery and equipment; cylinder head engine air-cooled. Brand: Amg2 (5251), Amg3, Amg4 (5086), AMG5, AMG6, АМГ61, АЛ8, АЛ13, АЛ23, АЛ27, АЛ28, АЛ29	Metal content by mass, %, not less	97
		The contamination harmless impurities, by mass, %, not more	3
		including iron, %, not more	2
A10	Waste products with a high content of zinc. Brand: В93, В94, B96, 1915 (7005), (1925)	Metal content by mass, %, not less	98
		The contamination harmless impurities, by mass, %, not more	2
		A contamination with iron	Not allowed
A11	Scrap aluminum material with a high content of zinc: parts of aircraft (including seaplanes) and helicopters and missiles — the spars, the nodes of the junction of the wings with the wing center section molded panel for covering the Stingers sealed cabs, the power part of the fuselage, rivet, bolt joints, welded and riveted load-bearing building structures. Brand: В92, В94, B95, 1915 (7005), (1925)	The aluminum content by weight, %, not less	97
		The contamination harmless impurities, by mass, %, not more	3
		A contamination with iron	Not allowed
A12	Waste of cast aluminium with low content of zinc, magnesium and copper. Brand: AL2, АЛ4, АЛ5, АЛ9, АЛ32, АЛ34, AK7, AK9	Metal content by mass, %, not less	98
		The contamination harmless impurities, by mass, %, not more	2
		A contamination with iron	Not allowed
A13	Scrap of cast aluminium with low content of zinc, magnesium and copper. Brand: AL2, АЛ4, АЛ5, АЛ9, АЛ32, АЛ34, AK7, AK9	Metal content by mass, %, not less	97
		The contamination harmless impurities, by mass, %, not more	3
		including iron, %, not more	2
A14	Waste aluminum with high copper content. Grade: AK5M2, АК7М2, AK5M7, AK5M4, AK8M3, АК4М4	Metal content by mass, %, not less	98
		The contamination harmless impurities, by mass, %, not more	2
		A contamination with iron	Not allowed
A15	Aluminum scrap with high copper content. Grade: AK5M2, АК7М2, AK5M7, AK5M4, AK8M3, АК4М4	Metal content by mass, %, not less	97
		The contamination harmless impurities, by mass, %, not more	3
		including iron, %, not more	2
A16	Scrap pistons cut without support, without bearings, shafts, steel rings, and other foreign substances. Brand: AK12M2, АК10М2, Ak12m2mgn, АК12МгН, AK18, АК21, 5M2, 5H2, AK4, AK4−1	Metal content by mass, %, not less	97
		The contamination harmless impurities, by mass, %, not more	3
		including:
		iron	0,5
		oil	2
A17	Scrap pistons undivided. Brand: AK12M2, АК10М2, Ak12m2mgn, АК12МгН, AK18, АК21, 5M2, 5H2, AK4, AK4−1	Metal content by mass, %, not less	50
		The contamination harmless impurities, by mass, %, not more	50
		including iron, %, not more	25
		Scrap that does not meet the requirements of this kind, comes by agreement between buyer and seller
A18	Scrap aluminum foundry mixed. Alloys aluminium-silicon	Metal content by mass, %, not less	80
		including zinc	1
		The contamination harmless impurities, by mass, %, not more	20
		including iron, %, not more	15
A19	Scrap aircraft split. Cast alloys without brass, babbit, bearings	Metal content by mass, %, not less	75
		The contamination harmless impurities, by mass, %, not more	25
		including:
		oil	2
		iron	10
A20	Aluminum scrap crushed without pieces of magnesium and zinc alloys. Casting and wrought alloys	Metal content by mass, %, not less	88
		The contamination harmless impurities, by mass, %, not more	12
		including:
		iron	1,5
		zinc alloy	3
		magnesium alloys	1
		rubber and plastic	1
A21	Clean aluminum shavings bulk sorted on groups of alloys in Al-Si foundry or deformable	Metallurgical yield mass, %, not less	90
		The contamination harmless impurities, by mass, %, not more	10
		including iron, %, not more	0,1
A22	The aluminum chips are combined in groups of 1−10	Metallurgical yield mass, %, not less	50
		The contamination harmless impurities, by mass, %, not more	50
		including iron, %, not more Supply parties with iron or magnesium more than 10% by agreement with the consumer	2
A23	Chip aluminum lunoobraznoe by types 1−10	Metallurgical yield mass, %, not less	40
		The contamination harmless impurities, by mass, %, not more	60
		including iron, %, not more	2
		Comes by agreement of a customer and the seller
A24	Toxins, releases, drosses, foam, fly ash, residues from the refining of aluminum metal alloys that do not contain zinc	Metallurgical yield mass, %, not less	80
		The zinc content by mass, %, not more	1
		The contamination harmless impurities, by mass, %, not more	20
		including iron, %, not more	2
A25	Toxins, releases, drosses, foam, fly ash, residues from the refining of aluminum metal alloys mixed	Metallurgical yield mass, %, not less	20
		The contamination harmless impurities, by mass, %, not more	80
		including iron, %, not more	2
		With less material and metallurgical output comes according to the agreement of the consumer and the seller
A26	Scrap cable products	Metal content by mass, %, not less	85
		The contamination harmless impurities, by mass, %, not more	15
		A contamination with iron	Not allowed
A27	Scrap household with a specific chemical composition	Metal content by mass, %, not less	90
		The contamination harmless impurities, by mass, %, not more	10
		including iron, %, not more	1
A28	Pre-molten scrap into ingots and ingots chemical composition	The metal content by mass, %, not less	99,6
A29	Scrap and waste that do not meet the requirements of the group 1−28	Comes by agreement of the parties	-
A30	Packages or briquettes of aluminum cans. Must not contain steel, lead, bottle caps, plastic cans, glass, wood, etc., For strapping packages unacceptable skids or support sheets of any material. Brand: AD0 (1050А), Amg2 (5251)	Metallurgical yield mass, %, not less	90
		The copper content by weight, %, max	0,2
		The contamination harmless, non-metallic impurities, by mass, %, not more	1
A31	Scrap aluminum radiators, aluminum parts cut with no valves brass and iron. Brand: AK9M2, AK7, etc.	Metal content by mass, %, not less	95
		The contamination harmless impurities, by mass, %, not more	5
A32	Waste wire and clean the cable cores. Brand: AD0 (1050А), AD1, AE	The aluminum content by weight, %, not less	98
		The iron content	Not allowed
		The contamination harmless, non-metallic impurities, by mass, %, not more	2
A33	Scrap mixed aluminum wire and cable without insulation, without the presence of a thin wire. Brand: AD0 (1050А), AD (1200), AE, 6063Е, 6101Е, 6082	Metal content by mass, %, not less	98
		The content of the wire alloy 6000 by weight, %, max	10
		The contamination harmless, non-metallic impurities, by mass, %, not more	2
A34	Scrap aircraft sheet cut from wrought alloys, except 7000 (V95, В93, etc.)	The metal content of the steel at yield, %, not less	85
		Contamination by iron, by mass, %, not more	5
		The contamination harmless, non-metallic impurities, by mass, %, not more	2
		Scrap deviations from these requirements are supplied as agreed between the seller and the buyer
A35	Scrap aluminum foil clean without having anodized and radar foil and crumbs, plastic, paper	The metal content in the steel output.	By agreement of the parties
		Delivery in packages and briquettes only by agreement between the seller and the buyer
A36	Wastes from the production of aluminum cans: trimmings, leaves, marriage, including with a thin layer of varnish, without covers with a seal. Brand: Amg2 (5251), AMH, AD31 (6063)	Metal content by mass, %, not less	98
		The copper content by weight, %, max	0,2
		The contamination harmless impurities, by mass, %, not more	2
		A contamination with iron	Not allowed
A37	Scrap cans of drinks coated paper, without the presence of debris, dirt and other impurities. Brand: Amg2 (5251), AMH, AD31 (6063), AD0 (1050А)	Metal content by mass, %, not less	96
		The copper content by weight, %, max	0,2
		The contamination harmless impurities, by mass, %, not more	4
		A contamination with iron	Not allowed
A38	Crushed scrap aluminum cans from drinks autmagically, plastic jars, glass and wood. Brand: Amg2 (5251), AD31 (6063), AD0 (1050А), etc.	Metal content by mass, %, not less	95
		Contamination with lead	Not allowed
		Contamination by iron, by mass, %, not more	0,2
		The contamination harmless impurities, including moisture, mass %, not more	5
		Scrap with a higher impurity comes by agreement between the seller and the buyer

Table 3 — Tungsten alloys and other tungsten chemical compounds

Group	Characteristic of the group	Figure	The norm
B1	Scrap and lump wastes of metal tungsten-alloy: pipes, rods, plates, marriage and shtabikov pieces, scraps of tape, foil cutting, hot stamping	The content of other metals and alloys	Not allowed
		The tungsten content, %, not less	99
		Impurity, %, not more	1
		The mass of the individual pieces, g, not less	10
B2	Scrap and lump wastes of metal oxidized tungsten: pipes, rods, plates, marriage and shtabikov pieces, scraps of tape, foil cutting, hot stamping	The content of other metals and alloys	Not allowed
		The tungsten content, %, not less	90
		Impurity, %, not more	10
		The mass of the individual pieces, g, not less	10
B3	Scrap and lump wastes of alloy based on tungsten with thorium. Brand: BT-50	The content of other metals and alloys	Not allowed
		The tungsten content, %, not less	97
		Impurity, %, not more	3
		The mass of the individual pieces, g, not less	10
B4	Scrap and lump waste tungsten-cobalt alloys: plates, drill bits, large-sized products, and fragments thereof. Brand: ВК3, ВК3-M, VK4, VK6, VK6-M, VK6, VK8, VK8-VK, ВК10, ВК10-M, VK-10КС, ВК11, ВК11-VK, ВК15, ВК20, ВК20-KS, ВК20К, ВК25	The content of other metals and alloys	Not allowed
		Metal content, %, not less	99
		Impurity, %, not more	1
		Tungsten content, %	70−90
		Cobalt content, %	3−25
B5	Scrap and lump waste tungsten-titanium-cobalt alloys: plate, drill. Brand: Т30К4, T15K6, Т14К8, Т5К10, Т5К12	The content of other metals and alloys	Not allowed
		Metal content, %, not less	99
		Impurity, %, not more	1
		Tungsten content, %	62−80
		The titanium content, %	4−24
		Cobalt content, %	4−12
		The mass of the individual pieces, g, not less	10
B6	Scrap and lump waste tungsten-titanium-tantalum-cobalt alloys. Brand: ТТ7К12, ТТ8К6, ТТ10К8−6, ТТ20К9, VK6-OM, ВК10-OM	The content of other metals and alloys	Not allowed
		Metal content, %, not less	98
		Impurity, %, not more	2
		Tungsten content, %	64−80
		The titanium content, %	3−10
		The content of tantalum, %	2−14
		Cobalt content, %	6−12
		The size of pieces, mm	10−200
V7	The pulverized waste from the production of mixtures of hard alloys	The content of other metals and alloys	Not allowed
		Metal content, %, not less	95
		Impurity, %, not more	5
		Tungsten content, %	60−90
		Cobalt content, %	0−15
		The titanium content, %	0−8
		The content of tantalum, %	0−1,5
		Particle size, mm less	3
B8	Dust a waste from the grinding of carbide inserts diamond tool	The content of other metals and alloys	Not allowed
		Metal content, %, not less	60
		Impurity, %, not more	40
		Tungsten content, %	25−40
		Cobalt content, %	4−8
		The titanium content, %	0−6
		The content of tantalum, %	0−2
		Particle size, mm less	3
B9	Waste dust from grinding carbide insert grinding	The content of other metals and alloys	Not allowed
		Metal content, %, not less	50
		Impurity, %, not more	50
		Tungsten content, %	25−40
		Cobalt content, %	4−8
		The titanium content, %	0−6
		The content of tantalum, %	0−2
		Particle size, mm less	3
B10	Lump wastes of molybdenum-tungsten alloy	The content of other metals and alloys	Not allowed
		The molybdenum content, %	50−70
		Tungsten content, %	30−50
Q11	Lump wastes and shavings of tungsten-copper alloy	The content of other metals and alloys	Not allowed
		Tungsten content, %	50−80
		Copper content, %	17−48
		Nickel content, %	0−2
		The silver content, %	0−2
B12	Waste tungsten-Nickel, tungsten-Nickel-iron alloys	The content of other metals and alloys	Not allowed
		Tungsten content, %	80−90
		Nickel content, %	5−10
B13	Chip, wire	The content of other metals and alloys	Not allowed
		Metal content, %, not less	90
		Impurity, %, not more	10
		Particle size, mm less	10
B14	Scrap cone bits	Without obstructions	-
B15	Powdered waste of tungsten and its alloys (powder, brooms, bran)	The content of other metals and alloys	Not allowed
		Metal content, %, not less	95
		Impurity, %, not more	5
		The tungsten content, %, not less	65
		Particle size, mm less	3
B16	Tungsten-containing chemical compound (paste, powder, brooms, bran chemical compounds)	The content of other metals and alloys	Not allowed
		Metal content, %, not less	75
		Impurity, %, not more	25
B17	Waste nitrate after etching tungsten-containing alloys (exhausted solution of nitrate)	Tungsten content, %	8−20
		The molybdenum content, %	5−10

Table 4 — Cadmium and its alloys

Group	Characteristic of the group	Figure	The norm
Кд1	Scrap and lump waste of non-alloy cadmium.	The content of other metals and alloys	Not allowed
	Brand: KD-0, KD-1, KD-2, KD-000, KD-0A	The cadmium content, %, not less	99
		Impurity, %, not more (oil, moisture and other non-metallic materials)	1
Kd2	Releases and pleski from melting and pouring of cadmium, cathode hooks and mesh-covered cadmium	Do not contain Nickel and its compounds, chlorides, fluorides, cyanides, organic compounds
		The cadmium content, %, not less	5

Table 5 — Cobalt and its compounds and alloys

Group	Characteristic of the group	Figure	The norm
1	Scrap and lump wastes	Do not contain zinc, lead, tin and their compounds, chlorides and fluorides. Cobalt content, %, not less	0,5
Ко2	Waste powder from sharpening high speed tool	Do not contain zinc, lead, tin and their compounds, chlorides and fluorides. Cobalt content, %, not less	0,3
Ко3	Spent catalysts, Packed	Metal content, %, not less	1

Table 6 — Magnesium and magnesium alloys

Group	Characteristic of the group	Figure	The norm
Мг1	Scrap and waste of non-alloy magnesium: trimming, punch, forgings, plates, mold casting. Brand: Мг96, Mg95, Mg90	Without the presence of copper, aluminum, zinc, lubricants.
		Metal content, %, not less	98
		Impurity, %, not more	2
		The size of the piece, mm, not more	1000x600
Мг2	Scrap of magnesium containing aluminium: sheets, castings, engine blocks, treads, wheels, planes, cars, transmission, etc. Brand: МЛ2, ML3, МЛ4, ML5, МЛ50Н, МЛ6, МЛ16	Scrap without inserts of other non-ferrous metals.
		Metal content, %, not less	98
		The content of components, %, not more
		Including:
		aluminium	10,2
		manganese	0,7
		zinc	3,5
		Impurity, %, not more	2
		The size of the piece, mm, not more	1000x600
Mg3	Trimming the sheet of wrought aluminium alloys in the manufacture of containers for gasoline, oil, parts, piping, welded structures subjected to moderate loads; extruded semi-finished products and forming. Brands: MA1, MA11	Metal content, %, not less	99
		The contents of aluminium and zinc	Not allowed
		The content of manganese, %	1,3−2,5
		Impurity, %, not more	1
		The size of the piece, mm, not more	1000x600
MG4	Scrap magnesium alloys containing zirconium, zinc, neodymium (niobium): shaped castings. Brand: ML8, ML9, ML10, ML11, ML12, ML15, ML19, MA12, MA14, MA15, MA5, MA2, МА10, MA19, MA20	Metal content, %, not less	98
		The content of components, %:
		cubic Zirconia	0,05−1,1
		zinc	0,2−7,0
		neodymium	1,4−3,5
		Impurity, %, not more	2
		Dimensions, mm, not more	1000x600
Мг5	Scrap magnesium alloys are mixed, besides the lithium-containing	Metal content, %, not less:	50
		The content of lithium and niobium	Not allowed
		Impurity, %, not more	50
		including iron, %, not more	25
Мг6	Shavings of magnesium and magnesium alloys, piketirovanijah	Metal content, %, not less	50
		Moisture content, %, not more	0,1
		Oil content, %, not more	0,5
Мг7	Waste products of magnesium alloys in the form of lumps and ingots	Metal content, %, not less	50
		Moisture content, %, not more	2
		Impurity, %, not more	50

Table 7 — Copper

Group	Characteristic of the group	Figure	The norm
M1	Copper conductors: wire and tyres are clean, without coatings and insulation. Brand: M00, М001к, M0 M0k, M1 M1K	Linked in coils, soft containers or in packages. Not contain non-metallic impurities, other metals. No burnt brittle phases, shiny surface, without moisture and oil.
		The output of the metal, %, not less	98
		The content of copper, %, not less	99,9
		Wire diameter, mm, not less	0,3
		Impurity, %, not more	2
		Weight of package, kg, not more	250
M2	Copper conductors: wire and tires, released from isolation by heat treatment. Scrap and lump wastes of electrolytic industry, not littered with other metals and alloys. Brand: M00, М001к, M0 M0k, M1 M1K	Linked in coils, soft containers or in packages. Not contain non-metallic impurities, other metals. No fragile burned plots allowed the existence of oxidized surface, without water and oil. The surface without oxide tint and traces of oxidation.
		The output of the metal, %, not less	97
		The content of copper, %, not less	99,9
		Wire diameter, mm, not less	0,5
		Impurity, %, not more	3
		Weight of package, kg, not more	250
M3	Scrap clean copper without coating, tinning and soldering: marriage cast, forged and stamped products trimming, die-cutting sheets, strips, pipes, gratings and wire without insulation, trolley with iron predelami. Scrap and lump wastes of electrolytic industry, not littered with other metals and alloys. Brand: M00, M0, M1, M2, M3	Linked in coils, soft containers or packages. Not contain non-metallic impurities, other metals, brittle burnt wire, no water, and oil. On the surface allowed the color of the tint and traces of oxidation. Allowed clean copper tubing. There may be fragments of other metals in the form of priderock. Without water and oil.
		The output of the metal, %, not less	95
		The content of copper, %, not less	99,5
		Impurity, %, not more	5
		including iron, %, not more	0,5
		Wire diameter, mm, not less	1,0
		Weight of package, kg, not more	250
		The mass of the individual pieces, kg, not more	100
M4	Scrap and waste mixed with Paluda and soldering. Brand: M00, M0, M1, M2, M3	Not contain non-metallic impurities of other non-ferrous metals. There may be fragments of other metals in the form of priderock. Without water and oil.
		The output of the metal, %, not less	94
		The content of copper, %, not less	99,5
		Impurity, %, not more	6
		including iron, %, not more	0,5
M5	Copper mixed scrap without burnt copper wire: conductors, coated with lacquer, Paluda, part, cooling units, coils	Galvanic cells are not allowed. Without water and oil.
		The output of the metal, %, not less	90
		The content of copper, %, not less	99,5
		Impurity, %, not more	10
		including iron, %, not more	0,5
M6	Scrap copper enamelled, lacquered wire in cotton insulation, insulation from fiberglass and paper or silk insulation (two layers). Brand: M00, M0, M1	Linked in coils, soft containers or packages. Does not contain non-metallic impurities, other metals. Without water and oil.
		The output of the metal, %, not less	93
		The content of copper, %, not less	99,9
		Impurity, %, not more	7
		Wire diameter, mm, not less	1,0
		The weight of the package, mm, not more	250
M7	Copper crumb of nalozhenii of copper without insulation. Brands: M0, M1	Does not contain non-metallic impurities, other metals. Without water and oil.
		The content of copper, %, not less	99,5
		The output of the metal, %, not less	98
		Impurity, %, not more	2
		including iron, %, not more	1
		Wire diameter, mm, not less	0,5
M8	Chips pure copper. Brand: M00, M0, M1, M2, M3	Without the presence of other metals.
		The output of the metal, %, not less	98
		The content of copper, %, not less	99,5
		Impurity, %, not more	2
		including oil and water, %, not more	1,5
M9	Scrap electric motors. Brands: M0, M1, M2, M3	Supply by agreement of the parties	-
M10	Mixed low-quality scrap copper	Supply by agreement of the parties	-
M11	Copper slag, dust, ash, and furnace granite breaking, Sora, goats	The output of the metal, %, not less	10
		The content of copper, %, not less	8
		The mass of the individual pieces, kg, not more	500
		With a smaller content of copper — supply by agreement of the parties
M12	Scrap of insulated copper wire	Scrap copper wire with different types of insulation.
		Supply by agreement of the parties	-
M13	Copper clad other non-ferrous metals	Supply by agreement of the parties	-

Table 8 — Brass

Group	Characteristic of the group	Figure	The norm
L1	Lump wastes of double brass: trimmings, marriage sheets, tapes, strips, rods, ingots, pipes and tubes. Brand: L96, L90, L85, L80, L70, L68, L63, L60	The content of other metals and alloys are not allowed. In coils, soft containers or packages. Without water and oil.
		Metal content, %, not less	98
		The content of copper, %, not less	60
		The content of zinc, %, not more	37
		Lead content, %, not more	0,07
		The non-metallic impurity content, %, not more	2
		The mass of the individual pieces, kg, not more	100
		Weight of package, kg, not more	250
L2	Scrap double brass without tinning and soldering: wire, art jewelry, gauge tube, flexible pipes, musical instruments, wire mesh, foil, pressure rolls for pickling works, accessories. Brand: L96, L90, L85, L80, L70, L68, L63, L60	The content of other metals and alloys are not allowed. In coils, soft containers or packages. Without water and oil.
		Metal content, %, not less	97
		The content of copper, %, not less	60
		The content of zinc, %, not more	37
		Lead content, %, not more	0,07
		Impurity, %, not more	3
		including iron, %, not more	0,5
		The mass of the individual pieces, kg, not more	100
		Weight of package, kg, not more	250
L3	Scrap brass double pipe heat exchanger after operation. Brand: L96, L90, L85, L80, L70, L68, L63, L60	The content of other metals and alloys are not allowed. In bundles (bundles) or bundles. Without water and oil.
		Metal content, %, not less	80
		The content of copper, %, not less	60
		The content of zinc, %, not more	37
		Lead content, %, not more	0,07
		Impurity, %, not more	20
		including iron, %, not more	0,5
		The mass of the individual pieces, kg, not more	100
		Weight of package, kg, not more	250
L4	Brass case gun. Brand: L70	The content of other metals and alloys are not allowed. Without the percussion cap sleeves. Without water and oil.
		Metal content, %, not less	97
		The antimony content is determined by user demand, %, not more	0,005
		The non-metallic impurity content, %, not more	3
L5	Brass brazed radiators and radiator pipes. Brand: L96, L90, L85, L80, L70, L68, L63, Л62	Delivery in disassembled form. The content of other metals and alloys are not allowed. Without water and oil.
		Metal content, %, not less	94
		Impurity, %, not more	6
		including iron, %, not more	0,5
L6	Scrap double brass with Paluda and soldering: in the marine — tubes for condensers and heat exchangers, sheets, strip, rods for tool-making, art products, gauge tube, flexible pipes, musical instruments, foil, pressure rolls for pickling works, accessories. Brand: L96, L90, L85, L80, L70, L68, L63	The content of other metals and alloys are not allowed. Without water and oil.
		Metal content, %, not less	97
		The content of copper, %, not less	60
		The content of zinc, %, not more	37
		The tin content, %, not more	0,1
		Lead content, %, not more	0,1
		Impurity, %, not more	3
		including iron, %, not more	0,5
		The mass of the individual pieces, kg, not more	100
L7	Waste and scrap of brass, alloyed with tin sheets, strip, rods for instrumentation, tubing for condensers and heat exchangers, art products, gauge tube, flexible pipes, musical instruments, foil, pressure rolls for pickling works, accessories. Brand: LO90−1, LO70−1, LO62−1, and ЛМцОС58−2-2−2, LOS	The content of other metals and alloys are not allowed. Without water and oil.
		Metal content, %, not less	97
		The content of copper, %, not less	57
		The content of zinc, %, not more	37
		The tin content, %, not more	2,5
		Impurity, %, not more	3
		including iron, %, not more	0,5
		The mass of the individual pieces, kg, not more	100
L8	Scrap brass, lead alloy: stop valves of sanitary products, ribbons, strips, sheets, tubes, rods, wire in the watchmaking, automotive industry and printing business. Brand: LS63−3, LS74−3, LS64−2, ЛС60−1, LS59−1, LS59−1V, LS59−1ЛД, LS-59−1L, LS58−2, LC40S, and LZHS58−1-1	The content of other metals and alloys are not allowed. Without water and oil.
		Metal content, %, not less	97
		Lead content, %, not more	3
		The content of copper, %, not less	57
		The content of zinc, %, not more	42
		Impurity, %, not more	3
		including iron, %, not more	0,5
		The mass of the individual pieces, kg, not more	100
L9	Waste and scrap of brass, alloyed with manganese: details of bearings, bushings, parts and fittings for shipbuilding, propellers, propeller blades. Brand: Lmc58−2, Lmc58−2L and ЛМцА57−3-1, Lzhmc59−1-1, ЛМцЖ55−3-1	The content of other metals and alloys are not allowed. Without water and oil.
		Metal content, %, not less	97
		The manganese content, %, not more	3
		The content of copper, %, not less	57
		The content of zinc, %, not more	45
		Impurity, %, not more	3
		including iron, %, not more	0,5
		The mass of the individual pieces, kg, not more	100
10	Waste and scrap of brass, alloyed with aluminium: tubes, rods, corrosion resistant parts, bushings, bearings, gauge springs instruments, insignia, accessories and art objects. Brand: LA77−2, ЛА67−2,5 D and LAN59−3-2, LAZH60−1-1, ЛАНКМц57−2-2,5−0,5−0,5	The content of other metals and alloys are not allowed. Without water and oil.
		Metal content, %, not less	97
		The aluminum content, %, not less	3
		The content of copper, %, not less	48
		Impurity, %, not more	3
		including iron, %, not more	0,5
		The mass of the individual pieces, kg, not more	100
11	Waste and scrap of brass, alloyed with silicon: forging, stamping, parts, operating in the marine environment, cast bearings and bushings. Grades: ЛК80−3, ЛК80−3L and ЛКС80−3-3,	The content of other metals and alloys are not allowed. Without water and oil.
		Metal content, %, not less	97
		The silicon content, %, not more	2,5
		The content of copper, %, not less	78
		The content of zinc, %, not more	18
		Impurity, %, not more	3
		including iron, %, not more	0,5
		The mass of the individual pieces, kg, not more	100
L12	The brass casings of artillery. Grade: ЛК75−0,5	The content of other metals and alloys are not allowed. Without the percussion cap sleeves. Without water and oil.
		Metal content, %, not less	97
		The content of copper, %, not less	74
		The silicon content, %, not more	0,75
		The contents of antimony (defined by the consumer), %, not more	0,005
		Impurity, %, not more	3
		including iron, %, not more	0,5
		The mass of the individual pieces, kg, not more	100
Л13	Scrap brass tin plated household: art, furniture, bowls, samovars, chandeliers, candlesticks. Brand: L80, L96, L85, L70	The content of other metals and alloys are not allowed. Without water and oil. Not allowed contamination with oil paint, resin, oil, paper and other water-insoluble materials.
		Metal content, %, not less	95
		The content of copper, %, not less	58
		The content of zinc, %, not less	18
		Impurity, %, not more	5
		including iron, %, not more	1
Л14	Scrap brass is mixed	Supply by agreement of the parties.
		Without moisture and oil.
		Metal content, %, not less	95
		Impurity, %, not more	5
15	The chips are double brass. Brand: L96, L90, L85, L80, L70, L68, L63, L60	The content of other metals and alloys are not allowed.
		Metal content, %, not less	94
		Impurity, %, not more	6
		including mechanical impurities, ferrous metals, %, not more	0,5
		The contents of water and oil, %, not more	2,5
16	Shavings of brass, alloyed with tin. Brand: LO90−1, LO70−1, LO62−1, and ЛМцОС58−2-2−2, LOS	The content of other metals and alloys are not allowed.
		Metal content, %, not less	95
		Impurity, %, not more	5
		including mechanical impurities, ferrous metals, %, not more	0,5
		The contents of water and oil, %, not more	2,5
17	Shavings of brass, alloyed with lead. Brand: LS63−3, LS74−3, LS64−2, ЛС60−1, LS59−1, LS59−1V, LS59−1ЛД, LS-59−1L and LZHS58−1-1, ЛМцОС58−2-2−2	The content of other metals and alloys are not allowed.
		Metal content, %, not less	95
		Impurity, %, not more	5
		including mechanical impurities, ferrous metals, %, not more	0,5
		The contents of water and oil, %, not more	2,5
Л18	Shavings of brass, alloyed with manganese. Brand: Lmc58−2, Lmc58−2L and ЛМцА57−3-1, Lzhmc59−1-1, ЛМцЖ55−3-1	The content of other metals and alloys are not allowed.
		Metal content, %, not less	95
		Impurity, %, not more	5
		including mechanical impurities, ferrous metals, %, not more	0,5
		The contents of water and oil, %, not more	2,5
Л19	The chips of brass, aluminum alloy. Brand: LA77−2, ЛА67−2D and LAN59−3-2, LAZH60−1-1, ЛАНКМц57−2-2,5−0,5−0,5	The content of other metals and alloys are not allowed.
		Metal content, %, not less	95
		Impurity, %, not more	5
		including mechanical impurities, ferrous metals, %, not more	0,5
		The contents of water and oil, %, not more	2,5
L20	Shavings of brass, alloyed with silicon. Brand: ЛК80−3, ЛК80−3L and ЛКС80−3-3	The content of other metals and alloys are not allowed.
		Metal content, %, not less	95
		Impurity, %, not more	5
		including mechanical impurities, ferrous metals, %, not more	0,5
		The contents of water and oil, %, not more	2,5
21	The brass shavings combined	The content of other metals and alloys are not allowed.
		Supply by agreement of the parties.
		The content of copper, %, not less	50
		Metal content, %, not less	95
		Impurity, %, not more	5
		including mechanical impurities, ferrous metals, %, not more	0,5
		The contents of water and oil, %, not more	2,5
Л22	Scrap and waste special brass: sheets, strips, ribbons, rods, tubes, wire, gauge tubes, condenser tubes in sea shipbuilding, mesh paper machines. Brand: ЛН65−5, ЛЖС1−1, Lmcsk, Lmcka	The content of other metals and alloys are not allowed. Without moisture and oil.
		The content of copper, %, not less	50
		Metal content, %, not less	97
		Impurity, %, not more	3
		including mechanical impurities, ferrous metals, %, not more	0,5
		The contents of water and oil, %, not more	2,5

Table 9 — Bronze

Group	Characteristic of the group	Figure	The norm
Probes unit 1	Lump wastes of bronzes with a high tin content: wire, rods, nets, springs, ribbon, strip, bearing parts, tube-blanks, tubes for measuring and control devices, gaskets, bushings and bearings. Brands: Bros, Broth, Brocs, Brisk	The content of other metals and alloys are not allowed.
		Metal content, %	97
		The tin content, %, not more	8,5
		Impurity, %, not more	3
		The mass of the individual pieces, kg, not more	100
Бр2	Scrap and lump wastes of bronzes with a high tin content: wire, rods, nets, springs, ribbon, strip, bearing parts, tube-blanks, tubes for measuring and control devices, gaskets, bushings and bearings. Brands: Bros, Bross, Brisk	The content of other metals and alloys are not allowed.
		Metal content, %, not less	90
		The tin content, %, not more	8,5
		Impurity, %, not more	10
		including iron, %, not more	5
		The mass of the individual pieces, kg, not more	100
Бр3	Lump wastes of bronze without tin: plates, sheets, strip, tubes, wire, bars, forgings. Brand: Bra5, Bra7, Brams, Brag	The content of other metals and alloys are not allowed.
		Metal content, %, not less	97
		The aluminum content, %, not more	11
		Impurity, %, not more	3
		The mass of the individual pieces, kg, not more	100
Бр4	Scrap and lump wastes of bronze without tin: plates, sheets, strip, tubes, wire, bars, forgings. Brand: Bra5, Bra7, Brams, Brag, Brams	The content of other metals and alloys are not allowed.
		Metal content, %, not less	90
		The aluminum content, %, not more	11
		Impurity, %, not more	10
		including iron, not more	8
		The mass of the individual pieces, kg, not more	100
Бр5	Lump wastes of bronze containing beryllium: rods, tubes, forgings, strips, wire. Brand: Brb2, Brbnt1,7; Brbnt1,9	The content of other metals and alloys are not allowed.
		Metal content, %, not less	97
		The contents of beryllium, %, not more	2,1
		Impurity, %, not more	3
		including iron, %, not more	0,5
		The mass of the individual pieces, kg, not more	One hundred
Бр6	Scrap and lump wastes of bronze containing beryllium: rods, tubes, forgings, strips, wire. Brand: Brb2, Brbnt1,7, Brbnt1,9	The content of other metals and alloys are not allowed.
		Metal content, %, not less	90
		The contents of beryllium, %, not more	2,1
		Impurity, %, not more	10
		including iron, %, not more	8
		The mass of the individual pieces, kg, not more	100
Бр7	Lump wastes of bronzes containing lead: parts, operating in severe conditions, gears, bushings, valves, gears for heavy duty cranes and power turbines, etc. Brand: BRS-30, БрСН60−2,5	The content of other metals and alloys are not allowed.
		Metal content, %, not less	97
		Lead content, %, not more	27
		Impurity, %, not more	3
		including iron, %, not more	0,5
		The mass of the individual pieces, kg, not more	100
Бр8	Scrap and lump wastes of bronzes containing lead: parts, operating in severe conditions, gears, bushings, valves, gears for heavy duty cranes and power turbines, etc. Brand: BRS-30, БрСН60−2,5	The content of other metals and alloys are not allowed.
		Metal content, %, not less	90
		Lead content, %, not more	27
		Impurity, %, not more	10
		including iron, %, not more	5
		The mass of the individual pieces, kg, not more	100
Бр9	Shavings of bronze with high tin content. Brands: Bros, Broth, Brocs, Brisk	The content of other non-ferrous metals and alloys are not allowed.
		Metal content, %, not less	95
		The tin content, %, not more	6
		Impurity, %, not more	5
		including mechanical impurities, ferrous metals, %, not more	1
		The contents of water and oil, %, not more	2
		The content of non-metallic materials, %, not more	2
Бр10	Chips bezolovni bronzes. Brand: Bra5, Bra7, Brams, Brag	The content of other non-ferrous metals and alloys are not allowed.
		Metal content, %, not less	95
		The aluminum content, %, not more	11
		Impurity, %, not more	5
		including mechanical impurities, ferrous metals, %, not more	1
		The contents of water and oil, %, not more	2
		The content of non-metallic materials, %, not more	2
Бр11	Chips bronzes doped with beryllium. Brand: Br, B2, Brbnt1,7; Brbnt1,9	The content of other non-ferrous metals and alloys are not allowed.
		Metal content, %, not less	95
		The contents of beryllium, %, not more	2
		Impurity, %, not more	5
		including mechanical impurities, ferrous metals, %, not more	1
		The contents of water and oil, %, not more	2
		The content of non-metallic materials, %, not more	2
Бр12	Shavings of bronze alloyed with lead. Brand: BRS-30	The content of other non-ferrous metals and alloys are not allowed.
		Metal content, %, not less	95
		Lead content, %, not more	10
		Impurity, %, not more	5
		including mechanical impurities, ferrous metals, %, not more	1
		The contents of water and oil, %, not more	2
		The content of non-metallic materials, %, not more	2
Бр13	Shavings bronze combined different grades of alloys	Supply by agreement of the parties.
		Metal content, %, not less	40
		Impurity, %, not more	60
		including iron, %, not more	3
Бр14	Scrap and lump wastes mixed	By agreement of the parties.
		Metal content, %, not less	60
		Impurity, %, not more	40
		including iron, %, not more	3

Table 10 — Molybdenum, molybdenum chemical compounds and alloys

Group	Characteristic of the group	Figure	The norm
Мо1	Lump waste of non-alloy molybdenum: pipes, rods, plates, marriage shtabikov, scraps of tape, foil, cutting hot stamping. Brand: MCH, MCIT, ACM, TSM-2A, Mr-47	The content of other metals and alloys are not allowed.
		Metal content, %, not less	99
		Impurity, %, not more	1
		The mass of the individual pieces, g, not less	10
Мо2	Scrap unalloyed molybdenum: pipe, rods, plate. Brand: MCH, MCIT, ACM, TSM-2A, Mr-47	The content of other metals and alloys are not allowed.
		Metal content, %, not less	98
		Impurity, %, not more	2
		The size of pieces, mm, not less	20
Мо3	Lump wastes of alloyed molybdenum: details of vacuum devices, a focusing electrode x-ray tubes, electric heating elements. Brand: TTSM, STC, NT	The content of other metals and alloys are not allowed.
		Metal content, %, not less	99
		The molybdenum content, %, not less	90
		Impurity, %, not more	1
		The size of pieces, mm, not less	20
Мо4	Scrap of alloyed molybdenum: details of vacuum devices, a focusing electrode x-ray tubes, electric heating elements. Brand: TTSM, STC, NT	The content of other metals and alloys are not allowed.
		Metal content, %, not less	98
		The molybdenum content, %, not less	90
		Impurity, %, not more	2
		The size of pieces, mm, not less	20
Мо5	Chip, wire	The content of other metals and alloys are not allowed.
		Metal content, %, not less	90
		The molybdenum content, %, not less	90
		Impurity, %, not more	10
Мо6	Waste powder: powder, brooms, Fannings. Brand: MUF MSC-1, MSC-2, mshv, MSH-1, MSH-2, PM-A, MSH-B, MP-B, MSH-1	The content of other metals and alloys are not allowed.
		Metal content, %, not less	95
		The molybdenum content, %, not less	95
		Impurity, %, not more	5
Мо7	Molybdenum chemical compound: paste, powder, brooms, bran	Metal content, %, not less	75
Мо8	Spent catalysts	Metal content, %, not less	5
		Moisture content, %, not more	10
Мо9	Other waste	Metal content, %, not less	20

Table 11 — Nickel and Nickel alloys

Group	Characteristic of the group	Figure	The norm
H1	Scrap and lump waste of non-alloy Nickel: trimming, die cutting, waste pipes, rods and wire; strip, plate, cathode sheets. Brand: N-0, N-1, N-1U, N-2, N-3, N-4, NP1, NP2, NP3, NP4, NPAN, NPA1, NPA2, Nomi, Np1jev, NP2JE	In packages or in bulk. Does not contain other metals and alloys, castings, soldered, fused or painted.
		Metal content, %, not less	97
		The contents of Nickel and cobalt in sum, %, not less	96
		Impurity, %, not more	3
		Thickness, mm, more	3
		The chunk-size, mm, not more	20
		Weight of package, kg, not more	250
H2	Scrap and lump wastes of alloyed Nickel: details of electrical devices and instruments; semi-finished products for electronic equipment. Grade: NK0,2; NK0,23; NK0,04; MWF; Nmg0,1; Nmg0,05v; Nmg0,08v; Nka0,07; NK0,013	In packages or in bulk. Does not contain other metals and alloys.
		Metal content, %, not less	97
		The contents of Nickel and cobalt in sum, %, not less	96
		The content of components, %, not more:
		silicon	0,25
		magnesium	0,12
		calcium	0,16
		Impurity, %, not more	3
		Weight of package, kg, not more	250
		The mass of the individual pieces, kg, not more	100
H3	Scrap low alloy Nickel alloys: semi-finished products for electronic equipment. Brand: NV3; Nv3v; Numg 3−0,05; Numg 3−0,08	The content of other metals and alloys are not allowed.
		Metal content, %, not less	97
		The contents of Nickel and cobalt in sum, %, not less	96
		The content of components, %, not more:
		magnesium	0,1
		tungsten	3,5
		Impurity, %, not more	3
H4	Scrap Nickel alloys containing manganese: candles automotive, aviation and tractor; tubes, thermocouple. Brands: 2,5 NMCs; NMCs 5; 2−2-1 Nmcac	The content of other metals and alloys are not allowed.
		Metal content, %, not less	97
		The contents of Nickel and cobalt in sum, %, not less	92,6
		The manganese content, %, not more	5,4
		Impurity, %, not more	3
		The mass of the individual pieces, kg, not more	100
H5	Scrap Nickel alloys containing chromium: thermocouples, compensation wires. Brand: NH9,5; NH9	Does not contain other metals and alloys.
		Metal content, %, not less	97
		The contents of Nickel and cobalt in sum, %, not less	88,6
		The chromium content, %, not more	10
		Impurity, %, not more	3
H6	Scrap and wastes of copper-Nickel alloys thermocouple, compensating wire, condenser tube oil coolers, tube sheets, air conditioners, pipes, parts for electrical engineering and instrumentation, plasmotrone products and welded structures for shipbuilding, planirovochnye material for medical instruments, springs, relays, Cutlery, artistic products (stamping and embossing). Brand: Mnmc43−0,5; Mnmc40−1,5; Mnzhmc30−1-1; MNZH5−1; MN19; MN16; MNC15−20; MNA6−1,5; Mnmc3−12; Mnmcazh3−12−0,3−0,3; MN0,6; Nmzhmc28−2,5−1,5; MN95−5; MNCS16−29−1,8; MNZHKT5−1-0,2−0,2	In packages or in bulk.
		The content of other metals and alloys are not allowed.
		Metal content, %, not less	97
		The contents of Nickel and cobalt in sum, %, not less	0,57
		The content of copper, %, not less	27
		Impurity, %, not more	3
		Weight of package, kg, not more	250
		The mass of the individual pieces, kg, not more	100
H7	Waste and scrap of Nickel silver instruments of precise mechanics, technical utensils. Brand: MNC15−20; MNCS16−29−1,8	The content of other metals and alloys are not allowed.
		Metal content, %, not less	97
		The contents of Nickel and cobalt in sum, %, not less	13,5
		The content of zinc, %, not less	18
		Impurity, %, not more	3
		The mass of the individual pieces, kg, not more	100
H8	Shavings of Nickel and Nickel alloys	The content of other metals and alloys are not allowed, including Nickel silver.
		Metal content, %, not less	97
		Impurity, % max (moisture and oil)	3
H9	Chips Nickel silver	The content of other metals and alloys are not allowed.
		Metal content, %, not less	88
		Impurity, % max (moisture and oil)	12
		Size, mm, not less	20
H10	Toxins, releases, furnace granite breaking, hearth furnaces, cathode hooks that pesky Nickel	Metal content, %, not less	20
		The mass of the individual pieces, kg, not more	100

Table 12 — Tin and tin-lead alloys

Group	Characteristic of the group	Figure	The norm
O1	Scrap and lump wastes of tin and alloys: semiconductor technology, tin tin, bars, rods, wire, tape, bearings, solders, babbit, powder, kitchen utensils. Brand: ovch-000, O1, O1 p. h, O2, O3, O4, B88, B83, В83С	The content of other non-ferrous metals and alloys are not allowed.
		Metal content, %, not less	97
		Impurity, %, not more	3
		The size of the individual pieces, mm, not more	200
O2	Scrap and lump wastes of tin and alloys with a low content of lead: semiconductor technology, tin tin, bars, rods, wire, tape, bearings, solders, babbit, powder, kitchen utensils. Brand: ovch-000, O1, O1 p. h, O2, O3, O4, B88, B83, В83С	The content of other non-ferrous metals and alloys are not allowed.
		Metal content, %, not less	97
		Lead content, %, not more	3,0
		Impurity, %, not more	3
		The size of the individual pieces, mm, not more	200
O3	Scrap and lump wastes of tin with a high lead content: typographic font, of bearings (babbit), solders. Brand: B16, bn, BS6, HT, H2, SH1, P1, P2, R2, CT1, CT2, HT, Y, K1, K2, Mn, Ln, LNG, GC, solders, BKA, BK2, BK2SH	Does not contain other non-ferrous metals and alloys.
		Metal content, %, not less	97
		The tin content, %, not less	1,8
		Lead content, %, not less	63
		Impurity, %, not more	3
		The size of the individual pieces, mm, not more	200
O4	Pot hooks and grid of tinning baths. Brand: ovch-000, O1, O1 p. h, O2, O3, O4, B88, B83, В83С	Not contain other non-ferrous metals and alloys.
		Metal content, %, not less	97
		Impurity, %, not more	3
O5	Shavings tin. Brand: ovch-000, O1, O1 p. h, O2, O3, O4, B88, B83, В83С	The content of other non-ferrous metals and alloys are not allowed.
		Metal content, %, not less	96
		The tin content, %, not less	80
		Impurity, %, not more	4
		including iron, %, not more	1,5
A6	Shavings tin-lead alloys combined. Brand: B16, bn, BS6, HT, H2, SH1, P1, P2, R2, CT1, CT2, HT, Y, K1, K2, Mn, Ln, LNG, GC, BKA, BK2, BK2SH	The content of other non-ferrous metals and alloys are not allowed.
		Metal content, %, not less	95
		The tin content, %, not less	1,8
		Impurity, %, not more	5
		including iron, %, not more	1,5
O7	Scrap tinplate	The content of other non-ferrous metals and alloys are not allowed.
		Supply by agreement of the parties	-
A8	Scrap and waste tin cans and tin containers	The content of other non-ferrous metals and alloys are not allowed.
		Supply by agreement of the parties	-
E9	Asgari, releases, the powder solders	The content of other non-ferrous metals and alloys are not allowed.
		Metal content, %, not less	95
		Impurity, %, not more	5
A10	Sludge, slag and other tin-containing waste	Supply by agreement of the parties.
		Metal content, %, not less	85
		Impurity, %, not more	15
		including iron, %, not more	8

Table 13 — Mercury and its compounds

Group	Characteristic of the group	Figure	The norm
R1	Mercury worked metal spilled from the out of operation of rectifiers and devices. Brand: P0, P1, P2, P3	The contents of mercury, %, not less	95
		Contamination of dissolved metals, organic compounds and mechanical impurities, %, not more	5
P2	Mercury worked the metal in the devices, out-of-use, including thermometers	The contents of mercury, %, not less	70
		Contamination of dissolved metals, %, not more	30
RZ	Solid waste of mercury in pharmaceutical and chemical industries with the inclusion of metallic mercury	The contents of mercury, %, not less	30
		Impurity, %, not more	70
P4	Lump wastes containing mercury engineering, electrical and other industries. Mercury-oxide elements	The contents of mercury, %, not less	2
R5	Mercury-containing sludge from various industries, containing metallic mercury and mercury in the form of compounds, flooring granite breaking, lining	Firm, uniform in size.
		The contents of mercury, %, not less	0,5
		The moisture content of sludge, %, not more	30
P6	Lamps with a mercury filling. Solutions containing mercury and waste mercury	The contents of mercury, %, not less	0,3

Table 14 — Lead and lead alloys

Group	Characteristic of the group	Figure	The norm
C1	Waste pieces of lead-alloy plates, strips, sheets, tubes, roles of wire. Brand: S0000, S000, S00, S0, S1, S1S, S2, S2S, S3S	The content of other non-ferrous metals and alloys are not allowed.
		Metal content, %, not less	97
		Lead content, %, not less	99
		The contents of antimony, arsenic and tin in the sum, %, not more	0,25
		Impurity, %, not more	3
S2	Scrap lead alloy plates, strips, sheets, tubes, roles of wire. Brand: S0000, S000, S00, S0, S1, S1S, S2, S2S, S3S	The content of other non-ferrous metals and alloys are not allowed.
		Metal content, %, not less	97
		Lead content, %, not less	99
		The contents of antimony, arsenic and tin in the sum, %, not more	0,25
		Impurity, %, not more	3
		including iron, %, not more	1
C3	Waste pieces of lead from the production of antimony cable sheath without a cotton braid and bitumen insulation cladding chemical installations and apparatus, manufacture of profiles, valves, pipe, shot, printing alloys shaped castings. Brand: SSU, Ssu8, Ssu10, US, USM, Ssua, ССу1, Ssu2, Ssu3, Ssumt, Ssum, Samoa, ССуМ2	The content of other non-ferrous metals and alloys are not allowed.
		Metal content, %, not less	95
		The antimony content, %, not more	12
		Impurity, %, not more	5
C4	Scrap lead from the production of antimony cable sheath, lining of chemical facilities and equipment, manufacture of profiles, valves, pipe, shot, printing alloys shaped castings. Scrap cable sheath does not meet the requirements of the group C3. Brand: SSU, Ssu8, Ssu10, US, USM, Ssua, ССу1, Ssu2, Ssu3, Ssumt, Ssum, Samoa, ССуМ2	The content of other non-ferrous metals and alloys are not allowed.
		Metal content, %, not less	90
		The antimony content, %, not more	12
		Impurity, %, not more	10
		including iron, %, not more	3
C5	Bulk waste from the calcium babbits used for pouring bearings. Grades: BKA, BK2, BK2SH, BK2C	The content of other non-ferrous metals and alloys are not allowed.
		Metal content, %, not less	95
		The content of calcium, %, not more	0.3 mm-1,15
		Impurity, %, not more	5
		including iron, %, not more	3
S6	Scrap calcium babbits. Brand: BKA, BK2, BK2SH, BK2C	The content of other non-ferrous metals and alloys are not allowed.
		Metal content, %, not less	85
		The content of calcium, %, not more	0.3 mm-1,15
		Impurity, %, not more	15
		including iron, %, not more	5
C7	Scrap and lump wastes mixed (unalloyed lead, antimony and lead calcium babbits). Brand: Рb1, Рb6	The content of other non-ferrous metals and alloys are not allowed.
		Metal content, %, not less	85
		The content of calcium, %, not more	0.3 mm-1,15
		Impurity, %, not more	15
		including iron, %, not more	5
C8	Chips of lead and lead alloys. Brand: S0000, S000, S00, S0, S1, S1S, S2, S2S, S3S	The content of other non-ferrous metals and alloys are not allowed.
		Metal content, %, not less	97
		Impurity, %, not more	3
C9	Chips of lead and antimony babbits. Brand: SSU, Ssu8, Ssu10, US, USM, Ssua, ССу1, Ssu2, Ssu3, Ssumt, Ssum, Samoa, ССуМ2, BKA, BK2, BK2SH, BK2C	The content of other non-ferrous metals and alloys are not allowed.
		Metal content, %, not less	90
		Impurity, %, not more	10
		including iron, %, not more	3
C10	The scrap lead-acid battery in ebonite monoblocks. Brand: S0000, S000, S00, S0, S1, S2, S3, Ssu8, Ssu10, US, USM, Ssua, Ssu3, Ssumt, ССу1	Uncut, with the electrolyte, without wooden boxes and iron pricelock.
		Metal content, %, not less	55
		Impurity, %, not more	45
C11	Scrap lead batteries in thermoplastic monoblocks. Brand: S0000, S000, S00, S0, S1, S2, S3, Ssu8, Ssu10, US, USM, Ssua, Ssu3, Ssumt, ССу1	Uncut, with the electrolyte, without wooden boxes and iron pricelock.
		Metal content, %, not less	65
		Impurity, %, not more	35
C12	Scrap lead-acid batteries in polyethylene and polypropylene monoblocks. Brand: S0000, S000, S00, S0, S1, S2, S3, Ssu8, Ssu10, US, USM, Ssua, Ssu3, Ssumt, ССу1	Uncut, with the electrolyte, without wooden boxes and iron pricelock.
		Metal content, %, not less	65
		Impurity, %, not more	35
C13	Scrap lead acid batteries mixed	Undivided, with the electrolyte.
		Metal content, %, not less	40
		Impurity, %, not more	60
C14	Scrap lead battery plates	Without monoblocs, covers, separators, rubber.
		Metal content, %, not less	75
		Impurity, %, not more	25
		Without contacts and jumpers.
		Metal content, %, not less	68
		Impurity, %, not more	32
		Moisture content, %, not more	5
C15	Scrap lead battery contacts and jumpers	Without plates, AIO, covers, separators, rubber.
		Metal content, %, not less	95
		Impurity, %, not more	5
C16	The battery slurries	The metal content (lead and antimony), %, not less	60
		Moisture content, %, not more	10
		Impurity, %, not more	40
C17	Sludge, slag, litharge, pasta, drawings, ishare, dust, ash and other lead-containing waste	Lead content, %, not less	10
		Moisture content, %, not more	15
		Impurity, %, not more	90
		including iron, %, not more	2

Table 15 Titanium and titanium alloys

Group	Characteristic of the group	Figure	The norm
T1	Scrap and lump wastes of titanium-alloy: housing filters, vacuum filters and thickeners, pumping and valving, tanks, columns and heat exchange equipment, ducts, flues, piping, sheet metal, trimming, cutting and alsecco. Brands: VT1−00, VT1−0	Scrap the split. Without ferrous metals, oil, emulsions and water. The surface must not be oxidized, no cracks, explosions, bundles.
		Metal content, %, not less	99
		Impurity, %, not more	1
		Weight of each piece:
		g, not less	100
		kg, not more	250
T2	Scrap and lump wastes of titanium alloys not containing tin: turbine blades, wire, rods, exhaust and inlet valves, rocker valves and silencers for diesel and automotive engines, load-bearing structures of vehicles, chassis of vehicles, heating coils, motors, vehicles, medical equipment. Grades: OT4−0, OT4−1, OT4, VT5, VT5−1, VT6, VT6S, VT3−1, VT9, VT14, ВТ16, VT20, VT22, PT-7M, ПТ3, PT-1M	Scrap the split. Without ferrous metals, oil, emulsions and water. The surface must not be oxidized, no cracks, explosions, bundles.
		Metal content, %, not less	99
		Impurity, %, not more	1
		Weight of each piece:
		g, not less	100
		kg, not more	250
T3	Scrap and lump wastes of titanium alloys doped with tin: mining equipment (punches hand). Brand: VT5−1, ВТ18У, TC5	Scrap the split. Without ferrous metals, oil, emulsions and water. The surface must not be oxidized, no cracks, explosions, bundles.
		Metal content, %, not less	99
		Impurity, %, not more	1
		Weight of each piece, kg, not more	250
T4	Sheet scraps of titanium and titanium alloys. Brands: VT1−00, VT1−0, OT4−0, OT4−1, OT4, VT5, W 5−1, W 6, W 6, W 3−1, W 9, W 14, W 16, W 20, VT22, PT-7M, ПТ3, PT-1, VT5−1, ВТ18У, TC5	Without ferrous metals, oil, emulsions and water. The surface must not be oxidized, no cracks, explosions, bundles.
		Metal content, %, not less	99
		Impurity, %, not more	1
		The size of the piece, mm, not more	60x60x60
		Dimensions of the briquette, mm, not more	600x600x600
T5	Shavings of titanium and titanium alloys. Brands: VT1−00, VT1−0, OT4−0, OT4−1, OT4, VT5, VT5−1, VT6, VT6S, VT3−1, VT9, VT14, ВТ16, VT20, VT22, PT-7M, ПТ3, PT-1, VT5−1, ВТ18У, TC5	Without ferrous metals, rubble, non magnetic tools, oil, emulsions and water.
		No visible tint.
		Metal content, %, not less	99
		Impurity, %, not more	1
		The length of the coil, mm	20−100
T6	Wastes of metallurgical production with high content of gas or not having a specific chemical composition: cinders, the battle of consumable electrodes, donnici, crown, foundry, splashy, tires, etc.	Supply by agreement of the parties	-
T7	Bulk waste and leaf trimmings, the press remains; ingots and semi-finished products from titanium alloys, rejected on chemical composition or mechanical properties	Supply by agreement of the parties	-

Table 16 — Zinc and zinc alloys

Group	Characteristic of the group	Figure	The norm
C1	Scrap and lump waste of non-alloy zinc: zinc scrap and rolling, the details of Avia — and auto-devices, chemical current sources (leaves), current sources (foil), trannie sheets, the printing plate, waste from punching, trimming sheets, tapes, wires, pipes, anodes, foil. Brand: CV00, CV0, CV, C0, Ц1С, C1, C2, Ц2С, C3, Ц3С, C0A	The content of zinc, %, not less	97,5
		The content of metal impurities, %, not more	2,5
		Does not contain the Paluda, soldering, rust.
		The chunk-size in the maximum dimension, mm, not more	1000
		The mass of the piece, kg, not more	100
		Weight of package, kg, not more	250
C2	Scrap and lump wastes of zinc alloys containing aluminum and copper, without inclusions. Clips bearings, separators of rolling bearings, shell tube, bearings, bushings sbalansirovannoi pendants, sliders, worm gears, carburetors, Souvenirs, consumer goods. Brand: CA4, CAM4−1, CAM4−1B CAM4−3, CAM9−1,5, CAM9−1,5 L, CAM10−5, CAM10−5L, ЦАМ30−5	The content of zinc, %, not less	97
		Contamination with benign substances, %, not more	3
		The chunk-size in the maximum dimension, mm, not more	1000
		The mass of the piece, kg, not more	250
C3	Scrap and lump wastes of zinc alloys containing aluminum and copper, with inclusions of: scrap bimetallic products, waste bimetallic strip. Brand: CA4, CAM4−1, CAM4−3, CAM9−1,5, CAM10−5	The content of zinc, %, not less	85
		Contamination with benign substances, %, not more	15
		including iron, %, not more	2
		The chunk-size in the maximum dimension, mm, not more	1000
		The mass of the piece, kg, not more	250
Ц4	The product of crushing of the hull, reinforcing, and decorative parts of automobiles and tractors: the case of carburetors, pumps, speedometer frames, radiator grille, handles. Brand: ZnAl4A, ZnAl4Cu1A, ZnAl4Cu3A, ZnAl4Cu3, Ca4o, CA4, CAM4−1o, CAM4−1, CAM4−3O, CAM4−3, ЦАМ8−1	The content of zinc, %, not less	90
		The content of metal impurities, %, not more	5
		The chunk-size in the maximum dimension, mm, not more	1000
		The mass of the piece, kg, not more	250
Ц5	Cast blocks or ingots of zinc: fused cast materials based on zinc in the form of smooth clean solid blocks or ingots without slag inclusions. Brand: CV00, CV0, CV, C0A, C0, C1, C2, C3	The content of zinc, %, not less	90
		Contamination with benign substances, %, not more	10
		Unit weight, kg, not more	100
Ц6	Zinc scrap coated	The content of zinc, %, not less	90
		Contamination with benign substances, %, not more	10
		The chunk-size in the maximum dimension, mm, not more	1000
		The mass of the piece, kg, not more	250
Ц7	Scrap and lump wastes of zinc alloys mixed	The content of zinc, %, not less	55
		Contamination with benign substances, %, not more	50
		including iron, %, not more	20
		The chunk-size in the maximum dimension, mm, not more	1000
		The mass of the piece, kg, not more	250
Ц8	Shavings of zinc and zinc alloys. Brand: CV00, CV0, CV, Ц02, C0, Ц1С, C1, C2, Ц2С, C3, Ц3С, CA4, CAM4−1, CAM4−3, CAM9−1,5, CAM10−5	The content of zinc, %, not less	85
		Contamination with benign substances, %, not more	15
		including iron, %, not more	3
		oil, moisture and other non-metallic materials, %, not more	12
		The chunk-size in the maximum dimension, mm, not more	1000
		The mass of the piece, kg, not more	250
Ц9	Getting	The content of zinc, %, not less	92
		Contamination with benign substances, %, not more	5
		The chunk-size in the maximum dimension, mm, not more	1000
		The mass of the piece, kg, not more	250
Ц10	Zinc dross, hartsink	The content of zinc, %, not less	85
		Contamination with benign substances, %, not more	15
		The chunk-size in the maximum dimension, mm, not more	1000
		The mass of the piece, kg, not more	250
Ц11	Dross Zinovieva	The content of zinc, %, not less	50
		Contamination with benign substances, %, not more	50
		The chunk-size in the maximum dimension, mm, not more	1000
		The mass of the piece, kg, not more	250
Ц12	Other waste, including scrap batteries	The content of zinc, %, not less	20
		Contamination with benign substances, %, not more	80
		The chunk-size in the maximum dimension, mm, not more	1000
		The mass of the piece, kg, not more	250

Table 17 — Scrap complex

Group	Characteristic of the group	Figure	The norm
Сл1	Leaded cable and copper wires in polyethylene, polystyrene and rubber insulation	Without armor in coils, bundles or pieces.
		The content of non-ferrous metals, %, not less	56
		Length, m, not more	1,5
Сл2	Leaded cables and wires with aluminium conductors with paper insulation	Without armor in coils, bundles or pieces.
		The content of non-ferrous metals, %, not less	82
		Length, m, not more	1,5
Сл3	Cable with aluminum sheath and copper core	Without armor in coils, bundles or pieces.
		The content of non-ferrous metals, %, not less	86
		Length, m, not more	1,5
Сл4	Lead bullets with cupro-Nickel or bimetallic shell	Sorted.
		Packed.
		The weight of one piece, kg, not less	40
Сл5	Nickel-cadmium batteries	Intact with the electrolyte in steel cans.
		Supply by agreement of the parties	-
Сл6	Nickel-iron batteries	Intact with the electrolyte. Supply by agreement of the parties	-
Сл7	Aluminum scrap and waste after the removal of selenium	By agreement of the parties. The content of selenium, %, not more	0,05

Table 18 — Bimetals

Group	Characteristic of the group	Figure
БМ1	Waste steel with a cladding layer: aluminium and its alloys copper and copper alloys Nickel and Nickel alloys	Supply by agreement of the parties. In bulk, in packages, rolls, coils, bundles, bundles
БМ2	Waste aluminium and its alloys with cladding layer: Titan copper aluminium silumin steel	Supply by agreement of the parties. In bulk, in packages, rolls, coils, bundles, bundles
БМ3	Waste of copper and its alloys with cladding layer: Nickel steel	Supply by agreement of the parties. In bulk, in packages, rolls, coils, bundles, bundles
БМ4	Wastes of Nickel and its alloys with cladding layer aluminium and its alloys	Supply by agreement of the parties. In bulk, in packages, rolls, coils, bundles, bundles
PM5	Waste of lead and its alloys with cladding layer is tin and its alloys	Supply by agreement of the parties. In bulk, in packages, rolls, coils, bundles, bundles
BM6	Waste other non-ferrous metals and alloys with cladding layer	Supply by agreement of the parties. In bulk, in packages, rolls, coils, bundles, bundles

5.2 waste and Scrap of non-ferrous metals and alloys included in the group tables 2−18, are governed by the chemical composition according to GOST 1583, 4658 GOST, GOST 4784, GOST 14113, 29103 GOST, GOST 123, GOST 859, GOST 15527, GOST 5017, GOST 18175, GOST, 1020 614 GOST, GOST 19241 and GOST 492, 804 GOST, GOST 2856, 14957 GOST, GOST 860, 1320 GOST, GOST 19807, GOST 3778, 1292 GOST, GOST 3640.

5.3 waste and Scrap of non-ferrous metals from alloys, not included in the group tables 2−18, produced by cancelled or re-introduce regulatory and technical documents that relate to the group to which they are suitable by chemical composition. Natural infestation of the types of waste products from nonferrous metals and alloys, not included in the set group, determined by reference tables of the debris of non-ferrous metals, is presented in Appendix J.

With the mismatched alloys chemical composition groups, are presented in tables 2−18, the classification of such alloys in the group are in agreement with the consumer.

5.4 Requirements described in tables 2−18, also apply to other similar quality group scrap and waste.

5.5 For scrap and waste in all group sizes must not exceed: packages 400x400x700 mm, ligaments and bays — 400x700 mm. Maximum dimensions of separate pieces in one of the dimensions should not exceed 1000 mm, with the exception of sizes specified in the tables for individual groups of scrap and waste.

The maximum dimensions of separate pieces of low-quality scrap and other waste must not exceed 1000x1000x2000 mm.

By agreement with consumer it is permitted to surrender scrap and waste exceeding these dimensions.

5.6 the Scrap and wastes of nonferrous metals and alloys on the name of the metal and of the group shall conform to table 2−18.

5.7 the Classification of scrap and waste of non-ferrous metals and alloys by groups is carried out visually in accordance with the external signs, labelling of parts and products — according to GOST 2171 or carrying out spectral and chemical analysis according to standard methods of measurement and the measurement procedures, certified in accordance with GOST R 8.563.

5.8 the Collection of scrap and waste of nonferrous metals and alloys should be carried out in accordance with the procedure given in Appendix A.

5.9 Scrap and wastes of nonferrous metals and alloys in the form of chrome-plated, Nickel-plated kadmirovannyh or coated otherwise plated parts and pieces, as well as parts and pieces coated or alloyed with silver, accept for certain types, like similar articles and pieces without metal coating.

5.10 permitted by agreement with the consumer to accept mixed waste and scrap excluding waste and scrap of titanium and titanium alloys.

Permitted by agreement with the customer to take (to take) mixed the types of scrap. By mixing scrap and waste of the same name, but different types, scrap and waste belong to the group with greater natural contamination.

5.11 In the scrap and waste of aluminium coated with selenium, the selenium needs to be removed to a residual content of 0.05% in place of lomoobrazovanija.

5.12 Bulk shavings all non-ferrous metals and alloys should have a length of one turn of not more than 100 mm. permitted by agreement with the consumer briquetting.

5.13 In the scrap and waste of non-ferrous metals and alloys are not allowed objects that are not related to natural contamination, which is not physically associated with scrap and waste — debris (rags, wood, paper, construction and packaging materials).

6 security Requirements

6.1 General

6.1.1 All delivered or shipped scrap and waste should be monitored for harmful chemicals, radiation monitoring and control]. Form of certificate of chemical, radiation and explosion and fire safety are given in Appendix B.

6.2 Requirements on chemical safety

6.2.1 All types of mercury-containing waste must be free of compounds with high explosive and radioactive properties. Containing mercury wastes containing toxic substances (fluoride, chloride, arsenic etc.) shall be subjected to neutralization by the enterprise provider. Mercury-containing sludge from sulfuric acid plants are not allowed.

6.2.2 the Degree of action on the human body harmful substances, which are allocated and formed in the process of harvesting and processing scrap and waste of nonferrous metals and alloys, the hazard class and the maximum permissible concentration (MPC) in working zone air and drinking water are fixed by GOST 12.1.005, GOST 12.1.007, GOST R 51232 and shown in table 19.


Table 19

Metal	The nature of the action on the human body	Pathways	Hazard class	PDK of harmful substances in the air of working zone, mg/m	Maximum permissible concentrations in drinking water, mg/DM
Al	Dust causes irritation of the mucous membranes of the eyes, nose, mouth, lung (lung aluminas)	Respiratory	III	2	0,5
W	Dust, oxide cause a violation of the gastrointestinal tract, irritation of the upper respiratory tract and respiratory system. Shots wire heal with difficulty	Respiratory	III	6	-
Cd	Dust, oxide, cause damage to the Central nervous system, internal organs, the violation of phosphoric-calcium metabolism, involvement of the gastrointestinal tract	Respiratory	I	0,05	-
Mg	Dust, oxide cause of inflammatory and suppurative processes of the skin	Skin	II	1,0	-
With	The dust causes a disturbance of carbohydrate metabolism, changes in the structure and function of the thyroid gland, lesion of the cardiovascular system, the digestive tract. Powdery wastes cause acute dermatitis	Respiratory	II	0,5	-
Si	Dust, oxide cause irritation of the upper respiratory tract, gastrointestinal tract, functional disorders of the nervous system	The respiratory system, the digestive intestinal tract	II	1,0	1,0
Mo	Dust, oxide cause functional disorders of the nervous system, metabolic abnormalities	The respiratory system, the digestive intestinal tract	III	3,0	0,25
Ni	Dust has a toxic effect, causing disorder of the Central nervous system, lower blood pressure, cause allergic diseases of the skin. The pair of electrolytes, salts are carcinogenic (cancer of the bronchi, nose, lungs, stomach). Salts have toxic effects: skin lesion («Nickel eczema», «Nickel itch»)	The respiratory system, skin	I	0,05	-
Sn	Dust, oxide cause lung disease, chronic bronchitis, respiratory insufficiency	Respiratory	-	-	-
Se	Toxic compounds cause liver, kidney and Central nervous system; salts cause burns and dermatitis	Digestive tract, skin	Ill	2	0,01
Pb	The lead oxide causes a disturbance of metabolic processes, nervous system, anemia, peptic ulcer disease, a violation of the energy balance of the cells	The respiratory system, the digestive intestinal tract	I	0,01	0,03
Ti	Dust causes respiratory irritation	Respiratory	IV	10	-
Zn	Dust, oxide cause disease of the upper respiratory tract, changes in digestive tract	The respiratory system, the digestive intestinal tract	III	0,5	5,0
Hg	Pair cause disturbance of calcium metabolism, changing proteins in the blood, reducing the protective functions of the organism, the Central nervous system, digestive tract	The respiratory system, the digestive tract, mucous membranes, skin	I	0,01	-

6.2.3 Control of content of harmful substances in the air of working zone is carried out in accordance with the requirements of GOST 12.1.005 and GOST 12.1.007.

Analysis of air samples is carried out according to normative documents approved by the Ministry of health of the Russian Federation, on methods of determination of harmful substances in the air or methodical instructions on determination methods and techniques developed in accordance with GOST 12.1.016, GOST R 8.563.

6.2.4 Drinking water must meet the requirements of GOST R 51232.1*. Analysis of drinking water levels of aluminum, copper, molybdenum should be carried out according to GOST 18165, 4388 GOST, GOST 18308, respectively, for lead and zinc — according to GOST 18293.
_______________
* Probably, the error of the original. Should read: GOST R 51232−98. — Note the manufacturer’s database.

6.2.5 All work with mercury-containing wastes is carried out in accordance with the sanitary rules and norms [1].

6.2.6 in the storage and transportation of scrap and waste of nonferrous metals and alloys should be secured to prevent spillage, education and filling of toxic and hazardous substances.

6.2.7 recycling, Disposal and destruction of hazardous substances must be conducted in accordance with the rules approved in the established order.

6.2.8 When working with scrap and waste of non-ferrous metals and alloys that have a toxic effect on the human body, you must use a respirator type «Petal» according to GOST 12.4.028.

6.2.9 When working with mercury and dusting of waste it is necessary to use filter gas respirator brand of the RPG-67 or G grade according to GOST 12.4.004 and a respirator «Petal» G according to the normative documents. The respirators shall periodically be subjected to demercurization and washing.

6.2.10 To prevent the ingress of dust, solid particles on the mucous membrane of the eye must wear protective goggles of types 2, 3 according to GOST R 12.4.230.1.

6.2.11 When working with waste tungsten, cobalt, magnesium, Nickel, providing allergic effects, it is necessary to use gloves according to GOST 12.4.010, apply anti-aerosol respirators in accordance with GOST R 12.4.191 or respirators type «Petal» according to GOST 12.4.028. Use dermatological protective equipment (preventive ointments, pastes, etc.) according to GOST 12.4.068. Allowed to use other prophylactic pastes and ointments, on the recommendation of the state sanitary inspection bodies.

6.2.12 In waste management cadmium need to wear gloves on regulations and aprons according to GOST 12.4.029.

6.2.13 personal protective equipment working with scrap and waste of nonferrous metals and alloys shall conform to standard industry regulations of free issue of special clothes, special footwear and other means of individual protection to workers and employees of the metallurgical industry and metallurgical production.

6.2.14 areas in the places of unloading and loading of scrap and waste, with harmful effects on the human body should be equipped with local suction according to GOST 12.4.021.

6.3 Requirements for ensuring explosion and fire safety

6.3.1 Enterprises and organizations, zagotavlja taking, processing and refiner scrap and wastes of nonferrous metals and their conductive or ship congestion at ports and other points should check the scrap and wastes of nonferrous metals on explosion safety in accordance with GOST 12.1.010.

6.3.2 fire and explosion hazard properties of the substances included in the composition of the scrap and waste of non-ferrous metals are shown in table 20.


Table 20

The name of the metal	View fire and explosion hazard of substances	Ignition temperature, °C	Lower explosive limit g/m	Extinguishing agents
Aluminium	Dust	550	35	Sand, ash
Tungsten	The same	-	-	-
Cadmium	«	-	-	-
Cobalt	«	-	-	-
Magnesium	Dust, powder, shavings, thin sheets	520	20	Sand, graphite
Copper	Dust, powder	-	-	-
Molybdenum	The same	-	-	-
Nickel	«	-	-	-
Tin	Dust	630	190	Sand
Titan	Dust, small chips	330	45	Graphite, talc
Zinc	Dust	600	480	Water, lime
Mercury	Hydrogen compound	-	-	-

6.3.3 random inspection of scrap and waste of non-ferrous metals explosion-not allowed.

6.3.4 Verification of scrap and waste of non-ferrous metals in the explosion (except for uncleared ammunition) should be carried out under the guidance of a person specially trained and having corresponding certificate. Upon detection of uncleared ammunition, containers with unknown contents, etc. work with scrap and waste of non-ferrous metals should be suspended.

6.3.5 Industrial premises and places of storage of explosive and flammable substances must comply with the fire safety requirements according to GOST 12.1.004, explosion protection according to GOST 12.1.010 and shall be equipped with signs of fire according to GOST R 12.4.026, fire-extinguishing means according to GOST 12.4.009 and fire alarm systems.

6.3.6 Production facilities in places of formation of harmful substances, explosive dust, and flammable substances must be equipped with ventilation according to GOST 12.4.021 separated from sources of fire, explosion and open fire with the provision of sanitary-hygienic requirements for working zone air in accordance with GOST 12.1.005, sealing equipment and communications.

6.3.7 For removing static electricity, a television and air vent installations must be grounded, executed and marked in accordance with GOST 12.2.007.0, GOST 12.2.007.14, GOST R 51321.1 and GOST 21130.

6.3.8 Disposal, removal, transportation, destruction of explosive scrap and waste of non-ferrous metals should be conducted by professionals competent regional authorities (representatives of military units and the Ministry of emergency situations, etc.)

6.3.9 waste and Scrap of non-ferrous metals and explosive items subject to processing in various ways (fire or mechanical cutting, packaging, crushing, etc.), should be checked for explosion safety in accordance with the following requirements.

6.3.10 Ammunition (shells, mines, warheads, bombs, etc.) should not have explosive devices, should be open point, unscrewed the bottom and it is empty, the internal surface must be cleared of explosives and special structures; shrapnel glasses and jet mines of the internal partition (membrane) should be removed.

6.3.11 the Trunks of artillery and small arms should be exposed through channels or deformed at the end of the barrel and the breech (receiver) to complex bending.

6.3.12 Store boxes of artillery and small arms should be open and empty or with bruises (to the cracks).

6.3.13 Artillery shells and casings of small arms should not have the means of ignition (percussion cap sleeves, galvanic and GalvanoTechnik tubes, etc.) and residues of propellant charge.

6.3.14 All types of military equipment should be rozpakowany, dismantled and released from fuels and lubricants, and are in their ammo, solid fuel and initiating other explosives should be removed, fluid from the hydraulic cylinder, brake, wheel and other devices to be merged.

6.3.15 Vessels of all types and sizes (tanks, barrels, etc.), and all hollow objects (cylinders, motors, etc.) must be cleared of content, the frost tubes and moisture and are available for inspection of the inner surface; of a mouth of cylinders should be opened and their enclosure should be slotted second opening; bottoms of barrels and other containers must be opened.

6.3.16 Capacity, units of machines (engines, transmissions, etc.) should be freed from residues of fuels and lubricants.

6.3.17 Frame, pallets, metal and other massive objects subjected to explosive fragmentation, should not have nizoralnyh charges or their residues.

6.3.18 Each vehicle scrap and waste of nonferrous metals is accompanied by a document certifying their explosion safety, chemical and radiation safety.

Form of certificates of explosion safety, chemical and radiation safety in the scrap and wastes of nonferrous metals is given in Appendix B.

6.3.19 Unloading and verification received by the company scrap and waste of non-ferrous metals on explosion safety should be carried out under the guidance of a person specially trained and having corresponding certificate. On the inspection must be recorded in the book of account received by the company scrap, specifying the name of the enterprise (organization) of the sender, invoice number and certificates of explosion safety, the name of the person who carried out the acceptance of scrap and waste, and his signature. Explosion-proof packet ensures that the sender.

6.3.20 Directly before loading into the mold, scoops and buckets waste and scrap of non-ferrous metals shall be tested for intrinsic safety in accordance with the requirements given in 6.3.4.

On the inspection must be recorded in the book of the account of the metal charge with the signature of the person who carried out the control of scrap and waste.

Work performed after issuance of permit to carry out works. Form of permit shown in Appendix B.

6.3.21 All work associated with the inspection of scrap and waste on the explosion and their decontamination should be carried out at an illumination of not less than 30 Lux.

6.3.22 When it detects explosive objects must be drawn up, the form of which is given in Annex G.

6.3.23 the Storage of explosive ordnance (except ordnance uncleared) is carried out in special storage facilities.

In storage and at a distance of less than 30 m from them is prohibited to use open fire and to carry out gas-welding works.

Storage should be provided molniezaschita and fire prevention equipment in accordance with the rules and regulations.

6.3.24 Received in the storage of explosive items must be placed in a stable position, eliminating the possibility of their fall.

6.3.25 safety Requirements in the processing and handling of scrap and waste of nonferrous metals is carried out in accordance with GOST 12.3.002 and technological documentation, duly approved.

6.3.26 in the selection, sample preparation, testing must comply with the safety requirements in accordance with GOST 12.1.005, GOST 12.1.007, GOST 12.2.009, 12.4.230.1 GOST R, GOST 12.4.021 R*, sanitary regulations [2], the rules approved in the established order.
_______________
* Probably, the error of the original. Should read: GOST 12.4.021−75. — Note the manufacturer’s database.

6.4 Requirements for radiation safety

6.4.1 Scrap and non-ferrous metal waste generated at the enterprises using in the production process, radioactive substances, and every vehicle should undergo decontamination and be accompanied by a document on decontamination.

In the absence of documents on the decontamination of the enterprises-suppliers should not make the scrap and wastes of non-ferrous metals.

6.4.2 waste and Scrap of non-ferrous metals (every vehicle), coming to the enterprises for gathering, procurement, implementation, and processing or use as a metal charge, must pass a radiation control in accordance with the requirements of sanitary regulations [2], sanitary rules and norms [3] and guidelines [4] with obtaining sanitary-epidemiological conclusions on the supplied party and be accompanied by a document on radiation safety. In the absence of these documents, scrap and waste of non-ferrous metals, as well as the vehicle on which the delivery on the company is not permitted until further order of the person responsible for radiation safety.

The dose rate of ionizing radiation and the flux density of particles on the surface of the scrap and waste metal should correspond to sanitary rules and norms [5]:

— 1st class of application (sending abroad) — less than 30 Mr/HR and 30 particles cm/min, respectively;

— 2nd class of application (in Russia) is less than 50 Mr/HR and 100 particles cm/min.

6.4.3 Verification of scrap and waste of non-ferrous metals to radiation safety shall be conducted by a person trained in accordance with the requirements of sanitary regulations [2], sanitary rules and norms [3], guidelines [4] and has a corresponding certificate. On the inspection must be recorded in the Ledger sent to an enterprise of scrap metal, stating:

— the name of the enterprise (organization) of the sender;

— the invoice number;

document on radiation control;

— the name of the person who carried out radiation control, and his signature.

7 Requirements of environmental protection

7.1 Protection of atmosphere from harmful emissions during processing and handling of scrap and waste of nonferrous metals is carried out in accordance with GOST 17.2.3.02 and sanitary rules and norms [6].

7.2 Waste water from the processing and work with scrap and waste of non-ferrous metals must be cleaned and discharged in accordance with the requirements of sanitary rules and norms [7].

7.3 Industrial waste from processing and handling of scrap and waste of non-ferrous metal shall be temporarily stored, transported, neutralizes and saharinata according to requirements of sanitary rules and norms [8].

8 Rules of acceptance

8.1 Scrap and wastes of nonferrous metals and alloys take parties. The party should consist of scrap and waste metal of one name, one group, or grade of alloy that is sent to one address and must be accompanied by:

8.1.1 Document about quality (passport), which must contain:

— the name of the supplier;

— the form of scrap and wastes;

— brand alloy;

— the weight of the batch;

— date of dispatch;

— the number of the vehicle;

— chemical composition.

The form of the passport is specified in Annex D.

8.1.2 a Certificate of explosion, which is issued in four copies: two copies are sent to the transport Department, one of which is fixed in a conspicuous place in the vehicle; the third copy direct to the consumer; and the fourth copy remains at the company, sending the scrap and wastes of nonferrous metals and alloys.

8.1.3 a Certificate of decontamination and neutralization of harmful substances in accordance with Annex E to the party scrap and waste coming from enterprises using in the production process, radioactive and harmful substances.

8.2 If the inspection party explosion-conduct continuous monitoring.

8.3 In accordance with the requirements of the basic sanitary work rules with radioactive substances and other sources of ionizing radiation services of the supplier is carried out radiation monitoring. Test scrap and waste of nonferrous metals and alloys, the contamination by radioactive substances is carried out dosimetric and radiometric devices in accordance with the sanitary rules and norms [3] and guidelines [4], the operating instructions of existing devices and existing enterprises methodological instruction (methods of measurement) of radiation control.

8.4 To verify scrap and waste of non-ferrous metals and alloys in compliance with the requirements of this standard, conduct sampling and preparation of samples in accordance with GOST 24231, 28053 GOST, GOST 28192. When sampling from scrap and lump waste to check the chemical composition and impurity contents from each party choose any at the discretion of the consumer the number of samples. Determination of the chemical composition of scrap and waste is carried out after the removal of dockage.

8.5 If the parties scrap and wastes in packaged form scree, mass fraction which is greater than 5%, and in brittoniana — more than 10%, the entire batch is accepted as delivered loose.

8.6 the Acceptance of scrap and waste of non-ferrous metals and alloys of all groups is carried out according to the weight of the metal.

8.7 In the acceptance of lead-acid Nickel-iron and Nickel-cadmium batteries check electrolyte and the integrity of the battery case.

8.8 acceptance of the net mass of metal (alloy) scrap and waste of non-ferrous metals and alloys is defined as the difference between the weight of a loaded vehicle and the gross vehicle weight, tare weight and dockage. For aluminum, magnesium and titanium, the presence of oxides of these metals is the contamination.

8.9 the acceptance of scrap and waste are listed below, with net weight determined according to GOST 28053, GOST 28192, is:

8.9.1 chip operation, the slag, propilovki, foils and powders of aluminum and its alloys chips, releases, toxins, propilovki, foils and powders of magnesium — the weight computed from the metallurgical output on the basis of laboratory tests.

8.9.2 For operation and Pleskov cadmium — mass they contain cadmium.

8.9.3 litter and metallurgical waste of copper and copper alloys — the mass of the copper (if the content is not less than 3%), zinc (if the content is not less than 5%), tin (if content is not less than 0.5%), lead (the content of not less than 1%), Nickel (if the content is not less than 1%).

8.9.4 waste of Nickel and Nickel alloys — mass of the contained Nickel, cobalt and copper.

8.9.5 other waste tin, tin and tin-lead alloys is the mass contained therein, tin, antimony, lead.

8.9.6 sludge and wastes of lead and its alloys is the mass of the contained lead, tin, antimony, and copper.

8.9.7 For zinc waste and zinc alloys — the mass contained in them, zinc, aluminum, and copper.

8.9.8 For lead and zinc ishari is the mass of the contained zinc and lead.

8.9.9 For tungsten — and molybdenum-containing compounds, dust, powder waste of hard alloys, chips — the mass of the contained tungsten and molybdenum (with the molybdenum content not more than 0.5%).

9 test Methods

9.1 Test scrap and waste of non-ferrous metals and alloys is carried out according to GOST 28053, GOST 28192 with the following additions:

9.1.1 Checking the classification to groups is carried out visually and the marking of parts and products according to GOST 2171 or by using drip reactions or spectral analysis methods, chemical analysis methods according to the normative documents.

9.2 Test scrap and waste of nonferrous metals and alloys, the explosion is carried out visually in accordance with the requirements specified in 6.3.

9.3 determination of the mass and size of the scrap and waste is carried out by weighing and measuring.

9.4 Test scrap and waste of nonferrous metals and alloys, the contamination by radioactive substances is carried out dosimetry devices SRP 68−01, DP-5V or other devices in accordance with the basic sanitary regulations [9] and norms of radiation safety [5], and also methodical recommendations on organization of work in the field of radiation safety at the enterprises of nonferrous metallurgy.

9.5 checking the correctness of scrap and waste of non-ferrous metals and alloys of groups is carried out visually or in the laboratory of the consumer; the results of the tests serve as the basis for acceptance and payments.

In case of disagreement in assessing the quality of scrap and waste of non-ferrous metals and alloys assessment is carried out on the sample selected in the presence of supplier’s representative, in the laboratory disinterested organization.

10 Transportation and storage

10.1 Transportation

10.1.1 the Scrap and wastes of nonferrous metals and alloys transporterowych any kind of transport in accordance with the rules in force in each mode of transport. Loading and unloading operations are conducted in accordance with the requirements of GOST 12.3.009, dangerous goods label according to GOST 19433, General cargo is prepared according to GOST 26653.

10.1.2 Transportation of scrap and waste of non-ferrous metals and alloys is carried out by rail in open wagons in accordance with the requirements of the technical conditions of loading and fastening of cargoes, approved in the established order. By agreement of the parties it is admitted to transport scrap and waste in covered wagons.

10.1.3 allowed to transport scrap and waste of non-ferrous metals and alloys in universal containers according to GOST 18477, wooden boxes according to GOST 2991, GOST 5959, in paper bags according to GOST R 53361, polyethylene bags according to GOST 17811, polyethylene film according to GOST 10354, metal barrels according to GOST 6247, GOST 17366 and other types of packaging by agreement of the parties.

10.1.4 allowed transportation in the same car two parties are one kind of metal under conditions that exclude them from the mix. Transportation in the car more than two parties scrap and wastes is carried out by agreement with the consumer. In the container transporterowych one party.

10.1.5 transporterowych Mercury-containing waste in covered wagons or open wagons in a sealed container.

10.1.6 the Scrap and wastes of nonferrous metals and alloys in the form of chrome-plated, Nickel-plated kadmirovannyh or coated otherwise plated parts and pieces, as well as parts and pieces coated or alloyed with silver, put in separate batches with indication of the coating material.

EBank opening and servicing 10.1.7 Due to explosion and fire briquettes shavings of magnesium and magnesium alloys transporterowych in a sealed package, excluding the moisture of the briquettes, in covered wagons, containers.

10.1.8 Scrap military equipment transporterowych separately.

10.1.9 Powdered waste aluminium and its alloys transporterowych in rubber chord or metal containers, by agreement of the parties in the gondolas.

10.1.10 the Scrap and wastes of nonferrous metals and alloys transporterowych river transport in universal containers (special) or transport packages.

10.1.11 Not allowed loading of scrap and waste of non-ferrous metals and alloys in the vehicle with the remains of previously transported cargoes (ore, gravel, etc.).

10.1.12 Transport of used lead-acid, Nickel-iron and Nickel-cadmium batteries carried in packaged form any kind of transport in accordance with the rules of transportation of new batteries, applicable to each mode of transport.

10.1.13 Packaging, lead-acid, Nickel-iron and Nickel-cadmium batteries is carried out to ensure their safe storage and transportation, excluding violation of the integrity of the buildings of the candy bars and the pouring of the electrolyte. Batteries placed on pallets in 3−4 series using the cushioning material, plastic film and fixed on the fixing tape.

10.2 Storage

10.2.1 the Scrap and wastes of nonferrous metals and alloys subject to primary processing, are stored separately on the groups of metals in accordance with the established classification in boxes, bins, compartments and specially designed areas with a hard surface, excluding the possibility of contamination of scrap and waste of non-ferrous metals and alloys.

10.2.2 Chips, powdered wastes and wastes of aluminium, zinc-containing, lead-containing of ishare that have passed initial processing, are stored under conditions excluding ingress of moisture.

10.2.3 Shavings of magnesium and magnesium alloys are kept in specially equipped warehouses located in isolated and fire resistant rooms.

10.2.4 Waste generated during the processing of alloys that contain beryllium, stored in closed containers or closed containers.

10.2.5 zinc-containing and lead-containing sludge and ishari stored under conditions preventing precipitation.

10.2.6 Powdered cobalt, tungsten, molybdenum wastes are stored under conditions excluding ingress of moisture and active chemical substances.

10.2.7 Mercury waste is stored in special hermetically sealed containers.

10.2.8 the Scrap lead-acid, Nickel-iron and Nickel-cadmium batteries kept in closed premises any of the following methods: on pallets, in containers with a lid, in special compartments, pits, equipped with collection systems leaking electrolyte.

10.2.9 Chips of titanium and titanium alloys, are stored in special containers. Chips titanium and titanium alloys with the colors of a tint are stored separately from non-oxidized chips.

10.2.10 the Scrap and wastes of nonferrous metals and alloys subject to primary processing, as well as goats, furnace granite breaking, aircraft and other oversized scrap stored outdoors.

10.2.11 allowed to store waste and scrap, except those specified in 10.2.2−10.2.9, outdoor areas for a period of not more than 10 days.

10.2.12 Household scrap is stored in closed premises.

10.2.13 Scrap military equipment are stored separately.

Annex a (mandatory). The procedure for collection of scrap and waste of non-ferrous metals and alloys

Appendix A
(required)

A. 1 Scrap and wastes of non-ferrous metals and alloys collected separately by names of metals and types of scrap and waste in accordance with the classification prescribed in the tables of this standard and metal, not included in this standard — technical documentation approved in the established order.

Not allowed the contamination of scrap and waste of non-ferrous metals non-metallic impurities, black and other colored metals.

A. 2 For the proper organization of the collection of waste generated in steel, metal, electrolytic, pickling, quenching, electroplating and other industries, all Metalworking equipment and machines equipped with protective devices, traps collections, to prevent the spreading of waste and promote concentration of them in a special metallomontag, allowing to carry out mechanized operations to liberate containers from the accumulated waste in compliance with safety regulations and sanitary standards. The places of waste generation install a sufficient number of boxes, pull out trays and other containers for separate waste collection. Quenching and pickling bath equipped with filter traps.

A. 3 Bulk waste and shavings are collected separately for each metal. Lunoobraznoe shavings are collected separate from the bulk of the chip.

Chips contaminated with emulsion and oil, is collected in a separate metalloboranes having openings for flow of emulsion and oil.

A. 4 the transition to processing from one brand of metal to another working place, metalloboranes and the floor is pre-released from waste previously treated metal.

A. 5 Chips and waste products of magnesium and magnesium alloys is collected in metalloboranes with closable lids in accordance with the regulations on safety and fire safety.

A. 6 Chips, sheet parings and other waste of titanium and titanium alloys are harvested separately according to the types. The chips with the color of the tint is collected separately from non-oxidized chips.

A. 7 Floors in places of metalwork must have coverage that excludes the trampling of the waste.

A. 8 Pulverized wastes generated from abrasive, diamond processing semi-finished products, molding, sharpening carbide and high speed tool is collected in the dust collector with the use of cooling in septic tanks with subsequent drying to air-dry state.

A. 9 non-ferrous metals contained in the processed solutions of them should be removed.

A. 10 Waste in the form of sludge, slag, operation, captured, Shari, scale etc. are collected separately for each metal.

Waste sludge and in which the metal content is below the regulatory legal documents, collect (with the exception of magnesium and its alloys) to secure the dumps separately for each metal.

A. 11 Scrap generated from the liquidation of fixed assets, depreciation of machinery interchangeable equipment, tooling, replacement parts and other products for repairs, and low-value assets and inventory, are collected separately under the names of metals (alloys).

A. 12 waste and Scrap cable products are collected separately by names of metals (aluminum, aluminum, lead, copper, copper — and lead-containing), by type of insulation (no insulation, enameled and lacquered; paper and silk insulation; nylon, Mylar, polyvinyl chloride and polyethylene insulation; rubber insulation), the outer protective cover and armor.

A. 13 the Scrap electrochemical cells and batteries are collected separately according to the name of the electrolyte (alkaline, saline).

A. 14 Scrap vacuum devices and electric lamps is collected separately for product groups.

A. 15 Household scrap collected separately under the names of metals.

A. 16 During the processing of a bimetal consisting of two or more non-ferrous metals, waste is collected in separate metalloboranes with an appropriate inscription.

A. 17 landfills (polygons) scrap and waste of non-ferrous metals, and metal waste, suitable for industrial use, is not allowed.

Appendix B (mandatory). Form of certificates of explosion safety, chemical and radiation safety of scrap and waste of non-ferrous metals and alloys

Appendix B
(required)

(name of deliverer)

ID N

on explosion safety, chemical and radiation safety of scrap and waste of non-ferrous metals and alloys

«____" _______________________20______G.

The recipient of scrap and waste

The name scrap and waste

Party N

Weight

t

Wagon (car) N

Invoice N

The results of radiation control:

— MED -radiation

Mr/HR

— PP -particles

part./min·cm

These scrap and waste comply with the requirements of this standard are explosion-proof, chemically safe, and radiation-safe and can be admitted for processing and use as a metal charge.

Responsible representatives of the enterprise-the deliverer:

at the explosion

(signature)

(signature)

on chemical safety

(signature)

(signature)

safety

(signature)

(signature)

Print

Annex b (mandatory). Form is the permit for the execution of works for cutting scrap and waste of non-ferrous metals

The App
(required)

(name of deliverer)
Permit for execution of works on cutting of scrap and waste of non-ferrous metals
«____" ______________________201______G.
Plot
Issued works
(position, full name)
With a team consisting
(list of surnames)
Safety measures when performing work
Work has begun		_______h_______min «____"____________________20____G.
Work is done		_______h_______min «____"____________________20____G.
The safety instructions in the workplace received
Permit issued
(signature, full name)
The manufacturer works
(signature, full name)

Appendix d (mandatory). The form of the act on the detection of explosive, chemical and radiation items when checking scrap and waste of non-ferrous metals

Appendix D
(required)

(company name)
CLAIM Head of consumer
«_____"____________________20_____G.
Print
ACT N about the detection of explosive, chemical and radiation items when checking scrap and waste of non-ferrous metals
Supplier of scrap and waste
The name scrap and waste
Weight	t
Wagon (car) N
Invoice N
Date of arrival «_____"_____________________20____G.
The certificate of explosion, chemical and radiation safety of scrap non-ferrous metals N______ from «______"________________20_____G.
The audit found:
(describe in detail each explosive, chemically hazardous and radiation-hazardous object)
Responsible representatives of the recipient:
at the explosion
(signature)				(signature)
on chemical safety
(signature)				(signature)
safety
(signature)				(signature)

Appendix e (mandatory). Form passport

Appendix E
(required)

Passport N
«_____"____________________20____G.
(name of supplier company)
Car N
	(container, car)
Name of metal and alloy		The form of scrap and waste			The symbol		The grade of metal and alloy designation ND
Continued
Chemical composition, %			Contamination, %			Notes
The representative of the supplier
(signature)
Seal or stamp of the technical control Department

Notes

1 Brand of metal and alloy and designation of the normative document and technical documentation specify only the shipment of scrap and waste at the Marche.

2 Chemical composition indicated in the case analysis.

3 the contract stipulate penalties for the supply of scrap and waste of non-ferrous metals and alloys without a passport.

Annex E (mandatory). Form of the certificate of decontamination and neutralization of harmful substances

Annex E
(required)

(company name)
ID N ________ on the decontamination and neutralization of harmful substances
«____" ________________________20_____G.
The recipient
Name
Party N
Weight
The number of the vehicle
(carriage, container, etc.)
Representative
supplying					(signed)			(position)		(Name)
Seal of the supplier

Annex W (informative). The table of the debris of non-ferrous metals

App W
(reference)

Table J. 1

The form of scrap	The average dockage, %
	Just	Iron		Oil	Other
Aluminum scrap
A piston aircraft engine with a radial arrangement of cylinders, split	70	65		-	5
Aircraft engines turbo-propeller	79	73		-	6
Aircraft engines turbojet:
axial compressor	71	66		-	5
centrifugal compressor	50	43		-	7
The engines with V-shaped arrangement of cylinders, uncut	65	62		3	-
Aluminium foil net	10	-		-	10
Aluminium foil with paper and the remains of dairy products	35	-		-	35
Aluminium foil lacquered, painted	20	-		-	20
Aluminum foil (corks from bottles with cardboard strips)	60	-		-	60
Aviation magnesium wheel size 1100x3300 mm	66	66		-	-
Aviation magnesium wheel size 580x3300 mm	30	30		-	-
Blades aviation: rings and deicing devices, uncut	10	8		-	2
The blades of the aircraft, scrapped	3	1		-	2
The screws are three-bladed aircraft already assembled	64	61		3	-
Lampshades, reflectors	40	-		-	40
Engines assembled	75	70		2	3
Aerosol cans, intact	22	9		-	13
Pads Aviatrassy	73	31		6	36
Tanks aircraft rubber	65	-		-	65
Blocks cylinder heads of V-engines, intact	45	42		3	-
Cylinder blocks with steel liners and studs V-engines	60	59		1	-
Scrap military (tube-Fuze with a clockwork mechanism; a percussion cap, bottom tube fuse), undivided	25	20		-	5
Head sewing machine	4	One		-	3
Arc tram	5	1		2	2
Arc mine electric locomotives	16	16		-	-
Carters V-engines with crankshafts	65	62		3	-
Carters:
with large iron studs	20	18		2	-
with a small iron bushings	15	13		2	-
Control cables, rubber insulation, aluminium conductors in non-flammable rubber sheath, an outer diameter of less than 25 mm	63	-		-	63
Control cables, rubber insulation, aluminium conductors in non-flammable rubber sheath, of an external diameter exceeding 25 mm	80	-		-	80
Control cables, rubber insulation, aluminium conductors in non-flammable rubber sheath, armored	82	29		-	53
Control cables in a PVC sheath with one living	58	-		-	58
Control cables in PVC shell with three or four conductors with a diameter of less than 16 mm	79	-		-	79
Control cables in PVC shell with three or four conductors with a diameter of over 16 mm	65	-		-	65
Control cables in PVC sheath, armored with two wires with cross-section up to 6 mm	96	37		-	59
Armored cables with two or four cores with cross-section exceeding 6 mm	80	29		-	51
Power cables with insulation of impregnated paper in an aluminum shell with three aluminum cores	33	-		-	33
Power cables with insulation of impregnated paper in an aluminum shell with four aluminium conductors	25	-		-	35
Power cables with insulation of impregnated paper in an aluminum shell with three aluminium conductors, armored	68	37		-	31
Power cables with insulation of impregnated paper in an aluminum shell with four aluminium conductors, armored	62	36		-	28
Control cables in PVC sheath, with aluminium conductors	64	-		-	64
Control cables in PVC sheath, armored	90	36		-	54
Baby carriage, uncut	80	44		-	36
Control cables in PVC sheath, with aluminium conductors	64	-		-	64
Control cables in PVC sheath, with aluminium conductors, armored	90	36		-	54
Baby carriage, uncut*	80	44		-	36
________________ * The text of the document corresponds to the original (repeat, see above). — Note the manufacturer’s database.
Trundle bed:
with a cloth	40	26		-	14
without the painting	30	26		-	4
Pads for rubber footwear with carbon	3	-		-	3
Kerosene stove, kerosene	15	13		-	2
Boxes of gas masks, painted with rubber hose and steel sleeve	10	4			6
Cover crankcase (magnesium)	50	50		-	-
Case incendiary bombs without the combustible mass	4	3		-	1
The blades of the helicopter MI-6 (length 175 cm)	78	76		-	2
Scrap the airframe of the MI-4, undivided	16	6		-	10
Scrap airframe IL	15	5		-	10
Scrap the airframe of the MIG:	35	25		-	10
wings, fuselages	35	25		5	5
tail	10	4		1	5
Pumps for inflating car tires, uncut	35	35		-	-
Blower automotive engines	18	16		2	-
The toe of the crankcase (magnesium)	70	69		-	1
The supercharger of an aircraft engine (magnesium)	40	39		-	1
Boxes of gas masks, painted on one side	5	-		-	5
Lights lighting	12	8		-	4
Pistons aircraft, tank, car with oil and soot, deveined	2	-		2	-
Automotive pistons with rings intact	14	13		1	1
The pistons air and tank with your fingers intact	22	21		1	-
Automotive pistons with rings and fingers intact	28	27		1	-
Air and tank pistons with rings intact	8	7		1	-
Dishes stamped:
split	3	-		-	3
uncut	8	5		-	3
Wires and tires without isolation	2	-		-	2
Wire paper insulation (diameter 10 mm)	5	-		-	5
Wire in cotton insulation	10	-		-	10
Wire lacquered	4	-		-	4
Installing a machine gun from aircraft (magnesium)	60	60		-	-
Reactors	70	-		-	70
Handles from a saw «Friendship"	37	-		-	37
Frame for mounting a machine gun, aircraft (magnesium)	50	50		-	-
Setcapacity hollow shafts with a pressed on axle	18	16		-	2
The mesh of paper mills with nylon	3	-		-	3
Wire ACSR designs:
normal	26	25		1	-
enhanced	40	39		1	-
lightweight	33	32		1	-
Scrap airplane with iron farms, uncut	40	30		-	10
Scrap aircraft (wings with small iron predelami), deveined	18	8		-	10
Pumps tank assembled	60	58		2	-
Brake magnesium aviation	80	78		-	2
Forms of bread, with iron corbels and Nagar stamps	26	22		-	4
Forms of bread, with iron corbels and Nagar stamps, alloy wheels	10	8		-	2
Jar dairy aluminum, uncut	15	14		-	1
The cylinders of aircraft engines	45	44		1	-
Drill mine:
assembled	61	57		1	3
without heads	47	44		One	2
Boat marine	40	35		2	3
Bobbin with predelami plastic	60	-		59	1
Bobbins for textile industry	70	-		-	70
Aluminum electrical capacitors, uncut	55	2		-	53
Scrap copper
Shafts sitesect copper-Nickel with steel bushings, split	10	10		-	-
The bearings (bi-metal: copper+iron)	92	92		-	-
Cable-martial with a diameter of 1 mm (two copper and five steel wires in mine)	93	21		-	72
Graphite rods coated with a thin layer of copper, the electrodes	90	-		-	90
The coil pipe (without scaling), cut	2	-		-	2
Control cables, rubber insulated, copper conductor in non-flammable rubber sheath, an outer diameter of less than 25 mm	38	-		-	38
Control cables, rubber insulated, copper conductor in non-flammable rubber sheath, of an external diameter exceeding 25 mm	63	-		-	63
Control cables, rubber insulated, copper conductor in non-flammable rubber sheath, armored	56	20		-	36
Cables with rubber isolation in PVC shell with one living	30	-		-	30
Cables with rubber isolation in PVC shell with three or four cores, with a diameter of less than 16 mm	53	-		-	58
Cables with rubber isolation in PVC shell with three or four cores, with a diameter of over 16 mm	37	-		-	37
Cables with rubber insulation in PVC sheath, armored with two wires with cross-section up to 6 mm	53	29		-	24
Cables with rubber insulation in PVC sheath, armored with two wires of section up to 66 mm	88	33		-	55
Capacitors with copper cores	56	56		-	-
Ship’s copper pipe with insulation (felt, asbestos), uncut, with a diameter of, mm:
10−100	45	-		-	45
100−300	25	-		-	25
Column of gas (without water system), deveined	2	-		-	2
Geysers assembled with mixer and faucet	36	34		-	2
Lived cable (after cutting by mechanical means)	1	-		1	-
Products sheets, rods, split	1	-		-	1
Conductors with a diameter of 1 mm with paper insulation	30	-		-	30
Conductors with a diameter of more than 1 mm tarred with cotton insulation (magnet wire)	15	-		-	15
Conductors with a diameter of 1 mm enamelled, lacquered	4	-		-	4
Conductors with a diameter greater than 1 mm, enamelled, lacquered	2	-		-	2
Conductors with a diameter of 1 mm with rubber and cotton insulation	52	-		-	52
Conductors with a diameter greater than 1 mm, with rubber and cotton insulation (wire external wiring power)	32	-		-	32
Conductors with a diameter greater than 1 mm, with rubber and cotton insulated, armored with steel mesh	72	30		-	42
Kitchenware (solder tinned), uncut	8	8		-	-
Copper wire annealed	2	-		-	2
Conductors with a diameter of more than 1 mm paper insulation	10	-		-	10
The tinned wire in cotton insulation brands POV, PMVG; in glass insulation brands PMUG, LOWS; in silk insulation brands mshv, mgshv, CMS, of an external diameter 0,9−3 mm	7	-		-	-
The tinned wire in cotton insulation grades for ungraded schools, PVG, COVE, MXVA etc., an outer diameter of 10−20 mm	24	24		-	-
Wire in plastic insulation brands HSV RITE, PTIT, CAVS, MSTB etc., of an external diameter 3−20 mm	37	37		-	-
Wire screened rubber hose, iron wire (CSA), outer diameter 8, 16 and 21 mm	70	26		-	44
Cables with cotton insulation and cotton hose brands TRUCKS, STACK, CAVE, WSE, CMSA etc., of an external diameter 11−32 mm	60	60		-	-
Setcapacity with steel shafts-axle shaft in the middle	50	48		-	2
Shafts setcapacity of black metal, covered with a copper shell with a thickness of 20−30 mm	80	80		-	-
Bands slug	1	-		-	1
Section copper powerful motor with mica, with insulation intact	28	-		-	28
Stilemedia lived in polyethylene grades P-274, GPR, MGM, MPCM and in the glass envelope of the brand, ESPO, outer diameter up to 10 mm	38	17		-	21
Bus transformer in isolation	22	-		-	22
Trolley, wires and other bare copper conductors, deveined	1	-		-	1
Copper furnace, split	2	-		-	2
Baths, boilers, uncut	12	10		-	2
The firebox of the locomotive with steel screens intact	50	45		-	5
Pipe coils with scale	5	-		-	5
Transformers copper with paper, uncut	88	85		-	3
Trolley with steel fixtures on the ends	3	3		-	-
The nichrome heaters with copper coil (immersion heaters), uncut	44	40		-	4
Motors with slip-ring rotors of the type AK, with a capacity of from 0.6 to 100 kW, fully assembled	83	73		-	10
Motors with squirrel-cage rotor	88	78		-	10
Scrap brass
The taps without iron couplings, but with cast-iron grates	7		6	-	1
Valves brass with aluminum heads and iron bolts	12		5	-	7
Valves brass with aluminum heads (without iron)	2		-	-	2
The sleeve gun, rifle, revolver, hunting without a cap and ball bushings, eat man world out there	1		-	-	1
The sleeve gun, rifle, cap and ball revolver with iron sleeves	3		2	-	1
Hunting shells and rocket with paper bullets, fired brass to the base, capsules with iron strip	50		-	-	50
Burner oil lamps with iron boxes and iron horses	70		68	-	2
Casings small-caliber	2		-	-	2
Hydrosylate	6		6	-	-
Kerosene burners with iron and horses without top reinforcement and constipation, uncut	6		4	-	2
Refrigerators water ship, uncut	17		17	-	-
Scrap brass castings and fittings, intact, faucets with iron couplings	8		7	-	1
Chandeliers with iron compounds (with wire)	10		10	-	-
Scrap brass (rings, pipes, plates, tanks without iron pricelock, etc.), split	1		-	-	1
Scrap brass, matrix	2		-	-	2
Candle holders table-iron core	4		4	-	-
Dishes household with a rolled iron wire in the top rim	6		4	-	2
The utensils from rolling of the brass — pots, bowls, cups, gravy boats, mugs (tinned without a rolled wire and other iron pricelock)	2		-	-	2
Stoves with iron legs and tubes intact	15		12	-	3
The bearings are brass, uncut	88		87	1	-
Radiators automotive, aviation and tractor, cut	6		6	-	-
Trucks and tank with iron pipes and iron capsules intact	36		29	1	6
Radiators aviation with iron shells, intact	12		6	-	6
Radiators with steel plates (brass or tomakomai pipes with cast iron pipes and the iron cage) are intact	78		72	-	6
Tractor radiators (cast iron casing), uncut	87		81	-	6
Tractor radiators and radiators for heating automobile cabin with a cast iron pipe with iron cover, uncut	50		49	1	-
Cutters brass	78		77	1	-
Samovars with cast iron grate, wooden handles, steel wire and bolts intact	15		9	-	6
Samovars, split	6		-	-	6
Mesh and mesh product, including grid paper factories	2		-	-	2
Glands intact	76		76	-	2
Separators with iron rivets and clips	68		68	-	-
A grid full of production material (cement and other factories)	15		-	-	15
Mesh, stabbed with a paper weight	6		-	-	6
Tube with sugar factories	4		-	-	4
The bases from the bulbs with a broken lamp, but with the mastic and remnants of glass	70		-	-	70
Electrocentrale, samovars, teapots with electroplating (inside)	20		-	-	20
Scrap lead
Batteries, car, tractor, tank without electrolyte:
in hard rubber tanks	45		-	-	45
in wooden boxes with ebonite tanks	55		-	-	55
Batteries in aircraft tanks ebony, uncut	45		-	-	45
Marine batteries in ebonite tanks intact	35		-	-	35
Scrap battery lead plates automotive, tractor and tank batteries with ebonite and wooden strips and ebony caps	25		-	-	25
Plate lead car, tank, airplane and tractor batteries with ebonite and wood strips	20		-	-	20
Lead plate marine batteries with separators (spacers)	Seventeen		-	-	17
Scrap battery lead plates without pads	15		-	-	15
Lead cable, removed by mechanical means	2		-	-	2
Lead cable molded cable, roasting, pig	1		-	-	1
Seal lead waste	3		-	-	3
Counterweights train rays (lead in the iron shell)	68		68	-	-
Lead roll, split	1		-	-	1
Lead roll with electrovan:
uncut	5		-	-	5
split	2		-	-	2
Lead pipes, split	5		-	-	5
Scrap Nickel, bronze, zinc
Bronze mechanical and artistic, split	2		-	-	2
The liners are cast iron, covered with bronze	84		84	-	-
Bushing bronze	1		-	-	1
Nickel silver ware (bowls, gravy boats, trays) with a rolled iron wire, uncut	6		6	-	-
Clichés zinc printing with wooden plates and studs, uncut	58		-	-	58
Zinc sheets triennia, uncut	12		12	-	-
The zinc anodes with steel predelami and the remnants of the electrolyte	3		3	-	-
Clichés zinc printing, cut	2		-	-	2
Worm gear with iron core	54		54	-	-
Difficult scrap
Bimetal bushing (iron+TSAM)	78		78	-	-
Power cables with insulation of impregnated paper lead sheath with aluminium conductors	22		-	-	22
Power cables with insulation of impregnated paper lead sheath, armoured, outer diameter less than 25 mm	49		22	-	27
Power cables with insulation of impregnated paper lead sheath, armoured, outer diameter more than 25 mm	38		16	-	22
Power cables with insulation of impregnated paper lead sheath, armoured, stranded three isolated leaded lived	55		20	-	35
Control cables, rubber insulation, aluminium conductors in lead sheath	21		-	-	21
Control cables, rubber insulation, aluminium conductors in a lead sheath, armoured	53		20	-	33
Power cables with insulation of impregnated paper lead sheath with copper conductor	12		-	-	12
Power cables with insulation of impregnated paper lead sheath with copper conductor, armoured, with a diameter of less than 25 mm	41		18	-	23
Power cables with insulation of impregnated paper lead sheath with copper conductor, armoured, with a diameter more than 25 mm	24		10	-	14
Power cables with insulation of impregnated paper lead sheath with copper conductors, twisted of the three isolated leaded lived	51		17	-	34
Control cables, rubber insulated, copper conductor in lead sheath	15		-	-	15
Control cables, rubber insulated, copper conductor in lead sheath, armoured	41		9	-	32
Power cables with insulation of impregnated paper in an aluminum shell with copper conductors (three or four)	14		-	-	14
Power cables with insulation of impregnated paper in an aluminum shell with three copper conductors, armored	50		27	-	23
Power cables with insulation of impregnated paper in an aluminum sheath four copper conductors, armored	42		32	-	10
Leaded power cable with insulation made from oiled paper, copper core with a diameter of 15−30 mm	16		-	-	16

Bibliography

[1]	Sanitary rules and norms SanPiN 4607−88	Sanitary rules for work with mercury, its compounds and devices with mercury filling
[2]	Sanitary rules SP 2.6.1.2612−10	Basic sanitary rules for ensuring radiation safety (OSPORB-99/2010)
[3]	Sanitary rules and norms SanPiN 2.6.1.2525−09	Hygienic requirements to ensure radiation safety in the procurement and sale of scrap metal
[4]	HOWTO MUK 2.6.1.1087−02	Radiation monitoring of scrap metal. HOWTO
[5]	Sanitary rules and norms SanPiN 2.6.1.2523−09	Radiation safety standards (NRB-99/2009)
[6]	Sanitary rules and norms 2.1.6.575 SanPiN-96*	Sanitary rules on atmospheric air protection of populated areas
________________ * On the territory of the Russian Federation the document is not valid. Act SanPiN 2.1.6.1032−01. — Note the manufacturer’s database.
[7]	Sanitary rules and norms SanPiN 4630−88*, SanPiN 5311−90	Sanitary rules and norms of surface water protection from contamination
________________ * On the territory of the Russian Federation the document is not valid. Act SanPiN 2.1.5.980−00. — Note the manufacturer’s database.
[8]	Sanitary rules and norms SanPiN 2.1.7.1322−03	Hygienic requirements to placing and neutralisation of production wastes and consumption
[9]	Sanitary rules SP 2.6.1.799−99*	Basic sanitary work rules with radioactive substances and other sources of ionizing radiation
________________ * On the territory of the Russian Federation the document is not valid. Valid SP 2.6.1.2612−10. — Note the manufacturer’s database.