GOST 2283-79

• gost-2283-79.pdf (498.04 KiB)
  ГОСТ 2283-79

GOST 2283−79 cold-rolled strips of tool and spring steel. Specifications (with Amendments No. 1, 2, 3, 4)

GOST 2283−79
Group B34

INTERSTATE STANDARD

COLD-ROLLED STRIPS OF TOOL AND SPRING STEEL

Specifications

Cold-rolled tool and spring steel strip. Specifications

ISS 77.140.25
OKP 12 3100

Date of introduction 1980−01−01

INFORMATION DATA

1. DEVELOPED AND INTRODUCED by the Ministry of ferrous metallurgy of the USSR

2. APPROVED AND promulgated by the Decree of the State Committee of standards of Ministerial Council of the USSR from 16.03.79 N 927

3. In the development of standards were used: ISO 4960−86

4. REPLACE GOST 2283−69, in addition to tape for Hach saws

5. REFERENCE NORMATIVE AND TECHNICAL DOCUMENTS

The designation of the reference document referenced	Item number
GOST 166−89	4.3
GOST 427−75	4.8
GOST 1435−99	2.1
GOST 1763−68	4.6
GOST 2789−73	2.10
GOST 3282−74	5.1; 5.3
GOST 3560−73	5.1; 5.3
GOST 4381−87	4.3
GOST 4543−71	2.1
GOST 5950−2000	2.1
GOST 6507−90	4.3
GOST 7566−94	3.1 a
GOST 8233−56	4.5
GOST 8273−75	5.3.1
GOST 8828−89	5.3.1
GOST 9569−79	5.3.1
GOST 10354−82	5.3.1
GOST 10396−84	5.3
GOST 10877−76	5.2
GOST 11701−84	4.4
GOST 12344−88	4.10
GOST 12345−2001	4.10
GOST 12346−78	4.10
GOST 12347−77	4.10
GOST 12348−78	4.10
GOST 12349−83	4.10
GOST 12350−78	4.10
GOST 12351−81*	4.10
GOST 12352−81	4.10
GOST 12353−78	4.10
GOST 12354−81	4.10
GOST 12355−78	4.10
GOST 14192−96	5.5 and
GOST 14959−79	2.1
GOST 15102−75	5.4
GOST 15150−69	5.7
GOST 15846−2002	5.8
GOST 16272−79	5.3.1
GOST 18617−83	5.3
GOST 19300−86	4.1, 4.2
GOST 20435−75	5.4
GOST 20799−88	5.2
GOST 21650−76	5.4
GOST 22225−76	5.4
GOST 22536.0−87	4.10
GOST 22536.1−88	4.10
GOST 22536.2−87	4.10
GOST 22536.3−88	4.10
GOST 22536.4−88	4.10
GOST 22536.5−87	4.10
GOST 22536.6−88	4.10
GOST 22536.7−88	4.10
GOST 22536.8−87	4.10
GOST 22536.9−88	4.10
GOST 22536.10−88	4.10
GOST 22536.11−87	4.10
GOST 22536.12−88	4.10
GOST 24597−81	5.4
GOST 27809−95	4.10
GOST 28473−90	4.10
GOST 29329−92	4.12
OST 38.01436−87	5.2

_______________
* On the territory of the Russian Federation GOST 12351−2003. — Note the CODE.

6. Limitation of actions taken by Protocol No. 5−94 of the Interstate Council for standardization, Metrology and certification (ICS 11−12−94)

7. EDITION (July 2003) with Changes 1, 2, 3, 4, approved in November 1981, February 1986, August 1986, July 1990 (ICS 1−82, 5−86, 11−86, 11−90), Amendment (ICS 8−2002)


This standard applies to cold rolled steel strip intended for the manufacture of springs, measuring tapes and other products.

(Changed edition, Rev. N 4).

1. CLASSIFICATION AND ASSORTMENT

1.1. The tape is divided into:

for precision manufacturing

thickness:

normal exactly

increased accuracy — T,

high precision.

width:

normal exactly

increased accuracy — sh;

in view of the surface

bright,

bright with the colors of a tint — TS,

dark;

by referring to edges

with cut edges,

with mill edges — BUT;

by type of processing

annealed:

ordinary quality,

high quality OP;

nagarebana:

common quality — N;

high quality NP;

the microstructure

without control of the microstructure;

with microstructure of granular perlite RFP.

1.2. Tape made sizes:

thickness: 0,10, 0,11, 0,12, 0,13, 0,14, 0,15, 0,16, 0,18, 0,20, 0,22, 0,24, 0,25, 0,26, 0,28, 0,30, 0,32, 0,34, 0,35, 0,36, 0,40, 0,42, 0,45, 0,50, 0,55, 0,60, 0,63, 0,65, 0,70, 0,75, 0,80, 0,85, 0,90, 0,95, 1,00, 1,05, 1,10, 1,15, 1,20, 1,25, 1,30, 1,35, 1,40, 1,45, 1,50, 1,55, 1,60, 1,65, 1,70, 1,75, 1,80, 1,85, 1,90, 1,95, 2,00, 2,10, 2,20, 2,30, 2,40, 2,50, 2,60, 2,80, 2,90, 3,00, 3,10, 3,20, 3,40, 3,50, 3,60, 3,80, 4,00;

width: 4, 5, 6, 7, 8, 9, 10, 12, 14, 15, 16, 17, 18, 20, 21, 22, 23, 24, 25, 26, 28, 30, 32, 34, 35, 36, 38, 40, 42, 45, 48, 50, 52, 55, 60, 63, 65, 70, 75, 80, 85, 90, 100, 110, 118, 120, 130, 140, 150, 160, 170, 180, 190, 200, 210, 220, 240, 250, 290, 300, 310, 320, 330, 340, 350, 360, 370, 380, 390, 400, 410, 420, 440, 450, 465 mm.

The width of the tape depending on the thickness of the tape shall be as defined in table.1.

Table 1

mm

The thickness of the strip	Tape width
From 0.10 to 0.40 incl.	4−250
SV. Of 0.40 «to 0.45 «	6−250
«To 0.45» to 0.50 «	6−300
«To 0.50» to 0.65 «	8−300
«To 0.65» to 0.85 «	8−465
«To 0.85» to 1.00 «	9−465
«1,00» 2,00 «	10−465
«2,00» 3,00 «	15−465
«3,00» 4,00 «	20−465

Note. Tape thickness greater than 2.00 mm with a width of 30 mm and a tape thickness greater than 3.00 mm for widths up to 40 mm are made by agreement between manufacturer and consumer.

By agreement between manufacturer and consumer tape is made of intermediate sizes for thickness and width with maximum deviation for the closest larger size.

1.3. Maximum deviations in thickness of the tape shall be as specified in table.2.

Table 2

mm

The thickness of the strip	Maximum deviation in thickness of the tape-precision manufacturing
normal	high	high
From 0.10 to 0.15	-0,02	-0,015	-0,01
SV. 0,15 «0,25	-0,03	-0,02	-0,015
«Of 0.25» to 0.40	-0,04	-0,03	-0,02
«0,40» 0,70	-0,05	-0,04	-0,03
«0,70» 0,95	-0,07	-0,05	-0,04
«0,95» of 1.30	-0,09	-0,06	-0,05
«1,30» of 1.70	-0,11	-0,08	-0,06
«1,70» 2,30	-0,13	-0,10	-0,08
«2,30» of 3.00	-0,16	-0,12	-0,10
«3,00» 4,00	-0,20	-0,16	-0,12

Note. By agreement between manufacturer and manufactured tape with double-sided (±) extreme deviations in thickness with preservation of tolerance.

1.4. Tolerances for the width of the tape shall be as specified in table.3.

Table 3

mm

The ultimate deviation in the width of the tape
The thickness of the strip	for the cropped strip width						for uncut ribbon
up to 100	over 100 to 300	over 300	up to 100	over 100 to 300	over 300	of the cropped strip width				from Pobre — Sanogo tackle
normal accuracy			increased accuracy			up to 100	over 100 to 200	over 200 to 300	over 300
From 0.10 to 0.63 incl.	-0,3	-0,4	-0,5	-0,2	-0,3	-0,4	+3	+4	+5	+6	+4% of nominal width
SV. 0,63 «1,00 «	-0,4	-0,5	-0,6	-0,3	-0,4	-0,5
«To 1.00» to 4.00 «	-0,6	-0,7	-0,8	-0,4	-0,5	-0,6

Note. By agreement between manufacturer and manufactured tape with double-sided (±) limit deviations on width preserving tolerance.


Examples of symbols

Ribbon of steel grade U10A, increased accuracy in thickness and width, light, with cut edges, nagarebana high quality, sizes 0,5h30 mm:

Tape U10A-TSH-With-NP-0,5h30 GOST 2283−79

Ribbon of steel U8A, high accuracy on thickness, normal accuracy in width, bright with cut edges, nagarebana ordinary quality, sizes 2,0х30 mm:

Tape U8A-T-C-H-2,0х30 GOST 2283−79

The same, with untrimmed edges:

Tape U8A-T-s-NO-N-2,0х30 GOST 2283−79.

1.1−1.4. (Changed edition, Rev. N 4).

2. TECHNICAL REQUIREMENTS

2.1. Cold-rolled strip from tool and spring steel must be manufactured in accordance with the requirements of this standard for technological regulations approved in the prescribed manner.

(Added, Rev. N 2).

2.1. Cold-rolled strip shall be made of steel grades:

50G according to GOST 4543;

U7A, U8A, U8GA, U10A according to GOST 1435;

60G, 65G, 70G, 85, 50KHFA, 60S2A, 65S2VA, 70S2KHA according to GOST 14959;

9KHF, 9ХФМ, 13X, KH6VF according to GOST 5950;

P9 in the NTD.

For the ribbon of steel grade 60S2A the deviation in the carbon content to ±0,02%. Strip of steel 60S2A made to 01.01.94. To strip of carbon tool steel grades U7A-U10A according to GOST 1435 the deviation in the chromium content up to 0,02%.

2.2. Mechanical properties of annealed and work-hardened strips of ordinary quality shall be as given in table.4.

Table 4

Steel grade	Nomi- tional thickness, mm	Tensile strength, N/mm(kgf/mm), not more	Elongation , %, not less	Tensile strength, N/mm(kgf/mm)
Ribbon annealed		Tape nagarebana
50G, 60G, 65G, 70G, U7A, U8A	To 1.50 incl.	640 (65)	15	740−1180 (75−120)
SV. 1,50	740 (75)	10
U8GA, U10A, 85	0.10 to 4.00 incl.	740 (45)	10	740−1180 (75−120)
9KHF, 9ХФМ, 13KH	930 (95)	-	-
P9, KH6VF	880 (90)	-	-
50KHFA, 60S2A, 65S2VA, 70S2KHA	880 (90)	8	780−1180 (80−120)

2.1, 2.2. (Changed edition, Rev. N 4).

2.2. Mechanical properties of annealed strip of high quality (OP) shall be as given in table.4A.

Table 4A

Steel grade	Nominal tape thickness, mm	Tensile strength , N/mm(kgf/mm), not more	Elongation , %, not less
50G	To 1.50 incl.	610 (62)	15
SV. 1,50	13
60G	To 1.50 incl.	620 (63)	15
SV. 1,50	12
65G	To 1.50 incl.	630 (64)	15
SV. 1,50	11
70G, U7A, U8A	SV. 1,50	640 (65)	10
85, U8GA	From 0.10 to 4.00 incl.	670 (68)	10
U10A	680 (69)	10
50KHFA	740 (75)	10

2.2 b. Tape nagarebana enhanced (NP) must be manufactured with the runway strength, are given in table.4, in the party, not more than:

150 N/mm(15 kgf/mm) — for tape up to a thickness of 0.36 mm incl.;

180 N/mm(18 kgf/mm) for tapes with a thickness St of 0.36 to 1.00 mm incl.;

200 N/mm(20 kgf/mm) for tapes with a thickness of 1.00 mm. St

By agreement with the consumer allowed to set a specific range of values of the interim resistance taking into account the above permissible values of run-up.

2.2 a, 2.2 b. (Added, Rev. N 4).

2.3, 2.4. (Deleted, Rev. N 3).

2.5. Tape with a microstructure of granular perlite is produced at the request of the consumer. If necessary, scale for the assessment of perlite and scoring of dispersion of the grains of cementite, and the ratio between granular and lamellar pearlite may be installed by agreement with the consumer.

(Changed edition, Rev. N 4).

2.6. The total depth of decarburization sided tape should not exceed:

0.01 mm — strip thickness from 0.1 to 0.25 mm

0.02 mm — tape thickness St of 0.25 mm to 0.50 mm,

0.04 mm — tape thickness St of 0.50 to 1.00 mm,

0.06 mm — tape thickness St of 1.00 to 2.00 mm,

0.08 mm — strip thickness St of 2.00 to 4.00 mm.

For a General layer depth bezoperatsionnogo take the zone of complete decarburization (ferrite) plus zone of partial decarburization.

Note. In agreement with the customer the tape can be manufactured without bezoperatsionnogo layer or with a reduced amount of decarburization compared to this, and without checking the depth of decarburization.


(Amendment).

2.7. (Deleted, Rev. N 3).

2.7. At the request of the consumer, as the strip of carbon steel should not be a carbon annealing (free of graphite).

(Added, Rev. N 1).

2.8. Light tape should have a surface of metallic color from light gray to dark gray shades.

The bright ribbon with the colors of tint allowed the oxidized surface with non-uniform colors or different shades.

The surface color is dark ribbon is not regulated. On the surface of the tape allowed the dark stains of pollution.

2.9. On the surface of the tape should not be captured, katanoi scale, okatannyh metal particles, rips and rust. Allowed a single prisoner, and some small scratches, scratches, fingerprints, rabini, the value of which does not exceed:

for bright and bright with flowers or ribbon — half of the limit deviations on thickness;

for the dark strip — tolerances for thickness.

2.8, 2.9. (Changed edition, Rev. N 4).

2.10. The roughness parameter of the surface light strips should be no more than 1,25 microns according to GOST 2789.

2.11. On the cut tape are not allowed ragged edge and notch depth of more than half of the limit deviations on width and burrs — more maximum deviations in thickness of the tape normal accuracy.

2.12. On the uncut tape is not allowed on the ragged edge of the depth tolerances for the width of the tape.

2.13. Striping tapes is not allowed.

2.14. Cropped tape is manufactured with a camber not exceeding on the segment of length 1 m:

5 mm for tape widths from 10 to 18 mm incl.;

4 mm — for tapes with a width of over 18 to 25 mm incl.;

3 mm for belt width 25 St to 50 mm incl.;

2 mm — for tapes of width over 50 mm.

By agreement between manufacturer and consumer clipped the tape is manufactured with a camber not exceeding 1 m length:

6 mm — for belt width from 10 to 40 mm incl.;

2.5 mm — for tapes with a width of over 40 mm.

Tape width less than 10 mm from the regulated rate for camber is made by agreement between manufacturer and consumer.

(Changed edition, Rev. N 4).

2.15. At the request of the consumer clipped the tape is manufactured with a flatness according to standards set with the consumer.

2.16. The tape shall be manufactured in coils with inner diameter from 200 to 850 mm. the Rolls of tape must be tightly and evenly wound.

2.17. Tape with a thickness of 1 mm or more can be supplied in strips, tied in bundles. The length of individual strips in a bundle must be from 2 to 3 m can be manufactured in a cropped strips the length from 1 to 2 m in amount of not exceeding 20% of the party.

2.18. The minimum mass of the coil is:

for tape widths up to 80 mm at the rate of at least 0.5 kg per 1 mm of width;

for tape widths over 80 mm — not less than 40 kg.

The minimum mass of the roll given in the Appendix.

In coordination with the consumer the maximum bale weight should not exceed 80 kg.

(Changed edition, Rev. N 2).

2.19. The coil should consist of one segment. Allowed the rolls of strips, consisting of two segments, in the amount not exceeding 10% of the party. Place of winding should be checked.

If the edges of the belt 3−4 single defect value of the established claim 2.11 allowed upon agreement with the consumer not to cut from a roll of defective parts subject to delivery to the consumer of additional quantity of tape (based on each defect 1 m length). Locations of defects must be marked with paint, gaskets or other means.

(Changed edition, Rev. N 4).

3. ACCEPTANCE RULES

3.1. Rules of acceptance GOST 7566.

(Added, Rev. N 4).

3.1. The ribbon take parties.

The party should consist of strips of the same steel grade, same bottoms, same size, one group of precision manufacturing, one type of surface and edges, one type of treatment and be accompanied by a document about quality that contains:

trademark or the name and trademark of manufacturer;

the symbol of the tape;

the number of melt showing the results plotnogo chemical analysis;

the results of the tests;

the number of coils, packs (packs) or of packages in the shipment;

the weight of the party.

By agreement with a consumer party may consist of strips of two different heats of the same steel grade.

(Changed edition, Rev. N 2).

3.2. To check dimensions, surface quality and edge take 5% of the rolls or packs of tapes, but at least two rolls or packs from the party.

3.3. From party tape, tested according to claim 3.2, should be selected:

to test a temporary resistance, relative elongation, depth bezoperatsionnogo layer, microstructure, delamination, camber, parameters of surface roughness, flatness and chemical composition (if necessary) — 1 roll from the party weighing up to 25 tons or 2 rolls from the party weighing over 5 tons.

3.2, 3.3. (Changed edition, Rev. N 4).

3.4. If unsatisfactory test results of at least one of the indicators it is carried out re-tests on twice the number of rolls. The results of repeated tests apply to the entire party.

4. TEST METHODS

4.1. The quality of the surface and the edges of the belt should be inspected visually without the use of magnifying devices. Quality control of surfaces and edges carried out on the 2−5 coil of the roll.

If necessary, the size of the surface defects of the tape is determined by the profiling-profilers according to GOST 19300 and other means of measuring the respective accuracy of normative-technical documentation.

To test a temporary resistance, relative elongation, depth bezoperatsionnogo layer, microstructure, delamination, camber, parameters of surface roughness, flatness and chemical composition (if necessary) from each selected according to claim 3.3 rolls or packs of cut one sample for each test.

4.2. The parameters of surface roughness of the tape should be determined by profiling-profilers according to GOST 19300 and other measuring instruments of appropriate accuracy.

4.3. Tape dimensions and size of defects on the edges of the belt must be checked with micrometers GOST 6507, 4381 GOST, GOST 166 calipers and other measuring instruments of appropriate accuracy according to normative-technical documentation.

The measurement of the thickness of the tape with a cut edge width of 20 mm and less hold in the middle of its width, of a width exceeding 20 mm — not less than 10 mm from the edge.

The thickness of the strip with mill edges measured at a distance of not less than 20 mm from the edge.

4.1−4.3. (Changed edition, Rev. N 4).

4.4. Tensile test on strips of thickness less than 3.00 mm should be carried out on samples of type I or type II according to GOST 11701. Allowed the test tape with a thickness of 1.7 mm and less spending on samples with an initial estimated length =80mm and width =20 mm.

Tape with a thickness of 3.0 mm and more test on samples with an initial estimated length =80mm and width =20 mm.

Preparation of samples for testing should be carried out in accordance with GOST 11701.

Allowed test strips with a width of less than 20 mm carried out on samples having a width equal to the width of the manufactured belt, with an initial estimated length =4, where the width of the tape made.

Samples for test cut out along the direction of rolling.

(Changed edition, Rev. N 2, 4)

.

4.5. Control of the microstructure of ribbon annealed at granular pearlite — a scale 2 GOST 8233.

4.5. Control in the absence of carbon annealing (free of graphite) to carbon tool steel should be carried out on longitudinal sections with increasing 350−400.

(Added, Rev. N 2).

4.6. Depth bezoperatsionnogo tape layer should be determined according to GOST 1763.

The choice of zoom metallographic method should provide accuracy of depth determination bezoperatsionnogo layer.

(Changed edition, Rev. N 4).

4.7. Striping tapes reveal by visual inspection of the edges of the tape or with the use of a magnifying glass to increase up to 7, and when testing it in tension. If necessary to identify the stratification used hot etched micro-sections in a 50% aqueous solution of hydrochloric acid with a temperature of 60−80 °C for 10 min.

4.8. Camber shall be checked by combining the edges of the sample tape with a length of 1 m with a straight line. The measurement is performed in the place of the greatest curvature of the ruler according to GOST 427, a set of probes for NTD and other means of measurement corresponding to the accuracy in the normative-technical documentation.

(Changed edition, Rev. N 4).

4.9. Measurement of the flatness of the tape is carried out according to the procedure agreed with the consumer.

4.10. The chemical composition of the metal tape is certified by a document of quality of the manufacturer of the metal. If necessary, the chemical composition of the metal strip is determined according to GOST 22536.0 to GOST 22536.12, GOST 27809, GOST 12344*-GOST 12355 host 28473.
_______________
* On the territory of the Russian Federation GOST 12344−2003. — Note the CODE.

4.11. Allowed to use non-destructive methods of control of mechanical properties and other characteristics specified according to coordinated methods.

4.12. Weighing of packages in the party, and if necessary rolls (packs) the tape should be on the weights according to GOST 29329, or other scales, providing weighing errors to 1%.

(Added, Rev. N 2).

5. PACKING, MARKING, TRANSPORTATION AND STORAGE

5.1. Each roll or bundle (package) of the ribbon should be tied in at least three places soft metal ribbon or wire according to GOST 3560, GOST 3282 or other regulatory-technical documentation.

Allowed other ways of fastening the coils to ensure the density of the winding and secure clamping of the ends of the tape and dimensional stability of the rolls during transportation. When securing the ends of the coils by spot welding, the depth of penetration should not exceed two thicknesses of tape.

At the request of the consumer the ends of the rolls of tape with a width of 30 mm or more spot-welds are not fixed.

(Changed edition, Rev. N 1, 2, 4).

5.2. The tape should be coated with a thin layer of inhibited lubrication, which protects the tape against corrosion.

Types of greases: a mixture of GSD and oil-12A AND I-20A GOST 20799 (ratio 1:1) mixture of NG-203A for OST 38.01436 and oil AND-or 18A-20A (at a ratio of 1:1), K-17 GOST 10877 other types of greases in other ratios of components of grease, providing protection against corrosion.

(Changed edition, Rev. N 4).

5.3. The rolls of tape of thickness 0.25 mm and less shall be wrapped with a layer of paper and Packed in wooden boxes type II according to GOST 18617 or other normative and technical documentation, tins, containers according to normative-technical documentation.

Tape thickness 0.25 mm pack:

during transportation on pallets made according to normative-technical documentation, the rolls placed one way:

on wooden or metal pallets in the stack (package) weight up to 1.25 T. the Coil or stack of coils should be wrapped in paper and attached to the pallet «under lock and key» at least three metal strips according to GOST 3560, or other regulatory-technical documentation. Permitted to attach the roll or stack of rolls to the pallet with a soft metal wire according to GOST 3282 or other normative technical documentation;

on wooden or metal pallets in the stack (packets) weighing up to 6 t, the lower roll of the foot is wrapped in paper or tape. The foot is attached to the pallet «under lock and key» at least three metal strips according to GOST 3560, or other regulatory-technical documentation. Additionally, bypassing the sump, stop the fourth tied off with a ribbon hanging metal label. The foot is wrapped with paper, and then non-conforming a metal sheet or a sheet obtained by welding of non-conforming sheets or ribbons, and tied off by forming a single metal band «under the castle». Top foot cover metal cover manufactured from substandard sheet or tape and having a circular shape with curved petals with the size not less than 50 mm, and tied on the petals of one with a metal band. Packed foot tied with «under the castle» with two mutually perpendicular metal strips, one of which is attached a metal marking label.

Change the packaging while ensuring quality packaging and security tape.

In coordination with the consumer the mass of the foot shall not exceed 5 tonnes;

during transportation without pallets coils, bundles (packs) the tape must be wrapped with a layer of paper, then a layer of polymeric film or fabric and stitched soft metal ribbon or wire according to GOST 3560, GOST 3282 or other normative and technical documentation in at least three places or by another method ensuring the safety of the package.

Mechanized method of packing the tape pack in one of the following ways:

the rolls of tape must be wrapped with a layer of paper according to GOST 10396 or other crepe paper according to normative-technical documentation, equal in protective properties;

coils shall be covered with removable inhibited polymer coating according to normative-technical documentation;

the rolls of tape must be wrapped waste metal strip. Packing is fixed by welding around the perimeter of the coil;

the rolls of tape must be wrapped with a layer of paper and fabric.

The method of packing is chosen by the manufacturer. In coordination with the consumer the ribbon more than 0.25 mm is not allowed to pack.

Tape thickness 0.25 mm and less can be transported on pallets.

(Changed edition, Rev. N 1, 2, 4).

5.3.1. The quality of packaging materials used:

the waxed paper according to GOST 9569;

paper double-layered wrapping according to GOST 8828;

the waxed paper according to GOST 8273 and other normative and technical documentation;

the polymeric film according to GOST 10354, 16272 GOST and other normative and technical documentation;

container holstoproshivny canvas — according to normative-technical documentation;

other types of packaging materials according to normative-technical documentation, with the exception of cotton and linen fabrics and also stitched the flap of the waste of the textile industry.

(Changed edition, Rev. N 2).

5.4. The tape is transported by all kinds of transport in covered vehicles in accordance with cargo carriage regulations applicable to transport of this form, and in transportation by railway in conformity with the technical conditions of loading and fastening of cargoes, approved by the Ministry of Railways of the USSR.

Consolidation packages in overpacks shall be carried out according to GOST 21650, GOST 24597.

Transportation of tape packages weighing up to 6 tons in metal packaging is carried out in open vehicles.

Allowed the transport of the tape in universal containers according to GOST 15102,20435 GOST, GOST 22225.

(Changed edition, Rev. N 4).

5.5. To each roll, bundle (package) or cargo should be attached label, which indicate:

trademark or the name and trademark of manufacturer;

the symbol of the tape;

batch number.

(Changed edition, Rev. N 2).

5.5. Transport marking under GOST 14192.

(Added, Rev. N 2).

5.6. (Deleted, Rev. N 2).

5.7. Store the tapes must conform to the conditions 2 GOST 15150.

(Changed edition, Rev. N 4).

5.8. The tape is sent to the far North and equivalent areas, shall be Packed in accordance with the requirements of GOST 15846 and of this standard.

(Added, Rev. N 4).

APP (reference)

APP
Reference

Tape width, mm	The minimum weight of roll, kg
4	2,0
5	2,5
6	3,0
7	3,5
8	4,0
9	4,5
10	5,0
12	6,0
14	7,0
15	7,5
16	8,0
17	8,5
18	9,0
20	10,0
21	10,5
22	11,0
23	11,5
24	12,0
25	12,5
26	13,0
28	14,0
30	15,0
32	16,0
34	17,0
35	17,5
36	18,0
38	19,0
40	20,0
42	21,0
45	22,5
48	24,0
50	25,0
52	26,0
55	27,5
60	30,0
63	31,5
65	32,5
70	35,0
75	37,5
80 or more	40,0

APP. (Added, Rev. N 2).