GOST 18389-2014

• gost-18389-2014.pdf (686.04 KiB)
  ГОСТ 18389-2014

GOST 18389−2014 Wire made of platinum and alloys on its basis. Specifications

GOST 18389−2014

INTERSTATE STANDARD

WIRE MADE OF PLATINUM AND ALLOYS ON ITS BASIS

Specifications

Wire made of platinum and its alloys. Specifications

ISS 77.150.99

Date of introduction 2015−09−01

Preface

Goals, basic principles and main procedure of works on interstate standardization have been established in GOST 1.0−92 «interstate standardization system. Basic provisions» and GOST 1.2−2009 «interstate standardization system. Interstate standards, rules and recommendations on interstate standardization. Rules of development, adoption, application, renewal and cancellation"

Data on standard

1 DEVELOPED by the Interstate technical Committee for standardization MTK 304 «Noble metals, alloys and industrial products», JSC «Ekaterinburg plant for processing non-ferrous metals"

2 as AMENDED by the Federal Agency for technical regulation and Metrology

3 ACCEPTED by the Interstate Council for standardization, Metrology and certification (Protocol dated 22 December 2014 No. 73-P)

The standard was accepted by voting:

Short name of the country MK (ISO 3166) 004−97	Country code MK (ISO 3166) 004−97	Abbreviated name of the national authority for standardization
Belarus	BY	Gosstandart Of The Republic Of Belarus
Kazakhstan	KZ	Gosstandart Of The Republic Of Kazakhstan
Kyrgyzstan	KG	Kyrgyzstandard
Russia	EN	Rosstandart
Tajikistan	TJ	Tajikstandart

4 by Order of the Federal Agency for technical regulation and Metrology dated 27 January 2015 N 21 St inter-state standard GOST 18389−2014 introduced as a national standard of the Russian Federation from September 1, 2015.

5 REPLACE GOST 18389−73


Information about the changes to this standard is published in the annual reference index «National standards», and the text changes and amendments — in monthly information index «National standards». In case of revision (replacement) or cancellation of this standard a notification will be published in the monthly information index «National standards». Relevant information, notification and lyrics are also posted in the information system of General use — on the official website of the Federal Agency for technical regulation and Metrology on the Internet

1 Scope

This standard applies to cold-drawn wire of platinum and alloys on its basis are used in instrumentation and other industries.

2 Normative references

The present standard features references to the following standards:

GOST 3193−74 Mesh catalyst of platinum alloys. Specifications

GOST 4381−87 Micrometers lever. General specifications

GOST 8273−75 wrapping Paper. Specifications

GOST 10197−70 Stands and tripods for the measuring heads. Specifications

GOST 12226−80Platinum. Methods of analysis

__________________

On the territory of the Russian Federation are 52519−2006 GOST R, GOST R 52520−2006, GOST R 52521−2006.


GOST 12551.1−82 Alloys platinum-copper. Methods for determination of copper

GOST 12551.2−82 Alloys platinum-copper. Methods of spectral analysis

GOST 12552.1−77 Alloys, platinum-Nickel. Method for the determination of Nickel

GOST 12552.2−77 Alloys, platinum-Nickel. Method of spectral analysis

GOST 12553.1−77 Alloys of platinum-palladium. Method for the determination of palladium

GOST 12553.2−77 Alloys of platinum-palladium. Method of spectral analysis

GOST 12554.1−83 Alloys of platinum-ruthenium. Method for the determination of ruthenium

GOST 12554.2−83 Alloys of platinum-ruthenium. Method of spectral analysis

GOST 12556.1−82 Alloys platinum-rhodium. Method for the determination of rhodium

GOST 12556.2−82 Alloys platinum-rhodium. Methods of spectral analysis

GOST 12559.1−82 Alloys platinum-iridium. Method of determination of iridium

GOST 12559.2−82 Alloys platinum-iridium. Methods of spectral analysis

GOST 13498−2010 Platinum and alloys on its basis. Brand

GOST 14192−96 Marking of cargo

GOST 15150−69 Machines, instruments and other technical products. Versions for different climatic areas. Categories, conditions of use, storage and transportation of the impact of climatic factors of the external environment

GOST 22864−83 precious metals and their alloys. General requirements for methods of analysis

__________________

On the territory of the Russian Federation GOST R 52599−2006.


GOST 24104−2001laboratory Scales. General specifications

__________________

On the territory of the Russian Federation GOST R 53228−2008.


GOST 28798−90 Head of the measuring spring. General specifications

GOST 29329−92Scales for static weighing. General technical requirements

__________________

On the territory of the Russian Federation GOST R 52599−2006.


GOST 30649−99 Alloys based on noble metals for jewellery. Brand

Note — When using this standard appropriate to test the effect of reference standards in the information system of General use — on the official website of the Federal Agency for technical regulation and Metrology on the Internet or in the annual information index «National standards» published as on January 1 of the current year, and the editions of the monthly information index «National standards» for the current year. If the reference standard is replaced (changed), when using this standard should be guided by replacing (amended) standard. If the reference standard is cancelled without replacement, then the situation in which the given link applies to the extent that does not affect this link.

3 Terms and definitions

This standard applies the following terms with respective definitions:

3.1 wire: Solid long product of uniform cross section throughout its length.

3.2 captivity: defect of a surface, representing a delamination of the metal azkabanu forms, United with the base metal on one side.

3.3 shell: the deepening on the surface of the product from the chipping of foreign objects or opening of the gas bubble.

3.4 stratification: the discontinuity of metal, oriented along the direction of deformation.

3.5 crack: a Defect of a surface, representing a rupture of the metal.

3.6 skein: a length of wire, wound into a series of continuous turns.

4 symbols and abbreviations

In the standard the following abbreviations are used to indicate accuracy of production:

N — normal, P — increased; to indicate the condition of delivery: M — soft, T — hard.

Examples of symbols when ordering:

Platinum wire brand of 99.93 PL, soft, with a diameter of 0.50, increased accuracy of production:

Wire PL Of 99.93 M 0,50 N GOST 18389-

Wire made of platinum-rhodium alloy grade Plrd 80−20, solid, diameter 2.00 mm, normal precision manufacturing:

Wire Plrd 80−20 T Of 2.00 N. GOST 18389-

5 Technical requirements

5.1 Main parameters and characteristics (properties)

5.1.1 Wire made of platinum and alloys on its basis (hereinafter wire) shall conform to the requirements of this standard and be manufactured according to the technological regulations approved in the prescribed manner.

5.1.2 the diameter of the wire and limit deviation should conform to the values specified in table 1.

Table 1

In millimeters

Wire diameter			Wire diameter
Wire diameter	Maximum deviation in precision manufacturing		Wire diameter	Maximum deviation in precision manufacturing
	high	normal		high	normal
0,020	-0,003	-0,005	0,10	-0,008	-0,015
0,022			0,11
0,025			0,12
0,028			0,14
0,030			0,15
0,032	-0,006	-0,008	0,16	-0,012	-0,020
0,036			0,18
0,040			0,20
0045			0,22
0,050			0,25
0,056			0,28
0,060	-0,006	-0,010	0,30
0,070			0,32
0,080			0,36	-0,020	-0,040
0,090			0,40
0,45	-0,020	-0,040	1,60	-0,035	Of -0.055
0,50			1,80
0,56			Of 2.00
0,60			2,20
0,63	-0,030	-0,045	2,50
0,70			2,80
0,80			Of 3.00
0,85			3,20	-0,040	-0,070
0,90			3,60
Of 1.00	-0,035	Of -0.055	Of 4.00
1,10			4,50
1,20			5,00
1,50			6,00
Notes 1 Wire from the alloys of PLI 75−25, 80−20 Plrd, 97,5 PLM, PLN 95,5, 92−8 Plru, Plru 90−10 is made with a diameter of 0.04 mm or more; from the alloys of 70−30 PLI, Plrd 70−30, 60−40 Plrd — with a diameter of 0.10 mm or more. 2 At the request of the consumer, the alloy wire PLM 91,5 manufactured with special treatment (stabilization). 3 by agreement with consumer it is permitted to produce wire of other diameters and/or other extreme deviations.

5.1.3 out-of-Roundness of the wire must not exceed half of the maximum deviations in diameter.

5.1.4 Estimated weight of 1 m of wire of platinum and alloys on its basis are given in Appendix A.

5.1.5 the Wire should be made of platinum and alloys on its basis with the chemical composition according to GOST 13498, GOST 30649.

Note — By agreement with consumer it is allowed manufacture of wire of platinum and alloys on its basis other brands.

5.1.6 Wire produced:

diameter of less than 0.10 mm — hard (unannealed);

with a diameter of 0.10 mm or more — soft (annealed) and hard (unannealed).

5.1.7 the surface of the wire should not be captured, cracks, cavities and delaminations.

Allowed color of a tint, local darkening of the wire, as well as surface damage, do not strip wire at reference sweep for tolerances for diameter.

5.1.8 Wire diameter of 0.3 mm or less is wound on a metal or plastic coil with a diameter of 20 mm, a wire diameter of 0.3 mm to 0.5 mm inclusive, the coil or coils, the wire diameter more than 0.5 mm — in coils only. Internal diameter of coil shall be not less than 60 mm.

Wire with a diameter of 4 mm and allowed to produce segments with a length from 200 to 1000 mm.

5.1.9 the Wire should be wound on a reel or folded into skeins rows, providing free spooling, with no sharp kinks. The distance between the upper row of the wire and the edge of the cheeks of the coil should be at least 3 mm.

5.1.10 Each coil (a coil) should consist of one piece of wire with no splices, knots. The ends of the wire on the coil (reel) must be firmly attached.

Each coil of wire with a diameter of 2 mm needs to be fixed ends of the wire of this coil.

5.1.11 the Ground wire on the coil (on the roll) shall be those specified in table 2.

Table 2

Wire diameter, mm	Weight of wire on coil (on a reel), g, not less
	nominal	reduced
From 0,020 to 0,03 incl.	0,7	0,3
SV. 0.03 to 0.05 incl.	1,8	1,0
SV. 0.05 to 0.10 incl.	5,5	2,0
SV. 0.10 to 0.20 incl.	16,0	5,0
SV. 0.20 to 0.40 incl.	27,0	10,0
SV. 0.40 to 1.00 incl.	55,0	25,0
SV. 1.00 to 2.00 incl.	150,0	75,0
SV. Of 2.00	300,0	150,0
Notes 1 Number of coils (coils) low mass should not exceed 15% of the batch weight. 2 By agreement with consumer it is permitted deviation of the mass of wire on spool (coiled) from the values listed in the table.

5.1.12 Electrical resistance and physical properties of the wire made of platinum and alloys on its basis are given in appendices B and C.

5.1.13 Properties of jewellery alloys based on platinum are given in GOST 30649.

5.2 Labeling, packaging

5.2.1 On the sides of each coil should be marked with a number and the mass of the coil (in hundredths of a gram).

5.2.2 To each coil (coils) of wire attached tag which must be specified:

— trademark of the manufacturer;

— designation of wire;

— the batch number.

5.2.3 wire Spool, Packed into plastic or cardboard boxes, and rolls of barbed wire, wrapped in paper according to GOST 8273, must be Packed in wooden boxes.

The free space in the box filled with soft packing material to protect the wire from mechanical damage.

Can be applied to other types of packaging and materials, ensuring the safety of wire during the transportation and storage.

5.2.4 the Boxes are sealed, or seal the wax seals. The seal (stamp) needs to have a clear impression of the manufacturer.

Transport marking under GOST 14192.

5.2.5 gross weight of the box should be no more than 10 kg.

5.2.6 Each batch of wire is accompanied by certificates of quality, comprising:

is the trademark or name and trademark of manufacturer;

— designation of wire;

— the batch number;

— chemical composition;

the number of coils (coils) in the party.;

— a lot of wire in the party, g;

— the month and year of manufacture;

stamp of technical control.

The certificate of quality is Packed in the last box, on which is marked: «Driving here."

6 acceptance Rules

6.1 Wire take parties. The party should consist of wire of one brand of metal (alloy), same diameter, one state and one precision manufacturing. The weight of the batch is not limited.

6.2 Checking of surface condition, measure the diameter and mass of the wire is subjected to each coil (a coil), verification of the gross mass of each box.

6.3 To determine the chemical composition, the consumer selects one coil (a coil) of the party, manufacturer — a sample from each heat.

6.4 Upon receipt of unsatisfactory results according to the chemical composition it is carried out re-testing at twice the sample taken from the coils (skeins) of the same party. The results of repeated tests apply to the entire party.

6.5 quality Control the labeling and packaging is subjected to each coil (a coil), box.

7 control Methods

7.1 wire Diameter is measured in two locations at a minimum distance of 100 mm from each other in two mutually perpendicular directions in each measured cross-section lever-type micrometer according to GOST 4381 spring or measuring head according to GOST 28798 with the rack according to GOST 10197.

Allowed the use of other measuring instruments providing the required accuracy.

7.2 the surface of the wire and winding quality check by visual inspection without the use of magnifying devices. The surface of the wire 0.1 mm in diameter and at least check with an increase of 7.

7.3 Chemical composition determines:

— platinum according to GOST 12226;

— alloys based on platinum — 3193 GOST, GOST 12551.1, 12551.2 GOST, GOST 12552.1,12552.2 GOST, GOST 12553.1, 12553.2 GOST, GOST 12554.1, 12554.2 GOST, GOST 12556.1,12556.2 GOST, GOST 12559.1, 12559.2 GOST, GOST 22864 or other methods, certified in the prescribed manner and providing the requirements of this standard.

7.4 the Mass of the wire is determined on laboratory weights according to GOST 24104. The gross weight of the boxes define the scales according to GOST 29329.

7.5 Marking and packaging checks visual inspection.

8 Transportation and storage

8.1 During transportation and storage of wire shall be protected from mechanical impacts, moisture and aggressive media.

Storage conditions — 1 (L) according GOST 15150.

8.2 Transport, storage and recording of wire is carried out in accordance with the rules of storage, transportation and accounting of precious metals.

9 manufacturer’s Warranty

9.1 the Manufacturer guarantees the conformity of the wire of platinum and alloys on its basis the requirements of this standard, under the conditions of transportation and storage prescribed by this standard.

A storage warranty period — 20 years from the date of manufacture. The date of manufacture should be the date of issue of the certificate about quality.

Annex a (informative). Estimated weight of 1 m of wire of platinum and alloys on its basis

Appendix A
(reference)

Table A. 1

Dia- meter in Provo Loki, mm	Square poperek- tion cross section, mm	Estimated weight of 1 m of wire, g
		PL Of 99.93	PLI 95−5	PLI 90−10	PLI 85−15	PLI 82,5−17,5	PLI 80−20	PLI 75−25	PLI 70−30
0,020	0,000314	0,00674	0,00675	0,00676	0,00678	0,00679	0,00679	-	-
0,022	0,000380	0,00815	0,00817	0,00818	0,00820	0,00821	0,00822	-	-
0,025	0,000491	0,01052	0,01055	0,01057	0,01059	0,01060	0,01062	-	-
0,028	0,000615	0,01320	0,01323	0,01326	0,01329	0,01330	0,01332	-	-
0,030	0,000707	0,01515	0,01519	0,01522	0,01525	0,01527	0,01529	-	-
0,032	0,000804	0,01724	0,01728	0,01731	0,01735	0,01737	0,01740	-	-
0,036	0,001017	0,02182	0,02187	0,02191	0,02196	0,02199	0,02202	-	-
0,040	0,001256	0,02694	0,02700	0,02705	0,02712	0,02714	0,02718	0,02723	-
0,045	0,001590	0,03410	0,03418	0,03424	0,03432	0,03435	0,03440	0,03446	-
0,050	0,001963	0,04210	0,04219	0,04227	0,04237	0,04241	0,04247	0,04255	-
0,056	0,002462	0,05280	0,05293	0,05303	0,05315	0,05320	0,05327	0,05337	-
0,060	0,002826	0,06062	0,06076	0,06087	0,06101	0,06107	0,06115	0,06127	-
0,070	0,003847	0,08251	0,08270	0,08285	0,08305	0,08312	0,08324	0,08339	-
0,080	0,005024	0,10776	0,10802	0,10822	0,10847	0,10857	0,10872	0,10892	-
0,090	0,006359	0,13639	0,13671	0,13696	0,13728	0,13741	0,13760	0,13785	-
0,10	0,00785	0,1684	0,1688	0,1691	0,1695	0,1696	0,1699	0,1702	0,1706
0,11	0,00950	0,2037	0,2042	0,2046	0,2051	0,2053	0,2055	0,2059	0,2064
0,12	0,01130	0,2425	0,2430	0,2435	0,2441	0,2443	0,2446	0,2451	0,2456
0,14	0,01539	0,3300	0,3308	0,3314	0,3322	0,3325	0,3330	0,3336	0,3343
0,15	0,01766	0,3789	0,3797	0,3805	0,3813	0,3817	0,3822	0,3829	0,3838
0,16	0,00031	0,0067	0,0068	0,0068	0,0068	0,0068	0,0068	0,0068	0,0068
0,18	0,02543	0,5456	0,5468	0,5478	0,5491	0,5496	0,5504	0,5514	0,5527
0,20	0,03140	0,6735	0,6751	0,6764	0,6779	0,6786	0,6795	0,6808	0,6823
0,22	0,03799	0,8150	0,8169	0,8184	0,8203	0,8211	0,8222	0,8237	0,8256
0,25	0,04906	1,0524	1,0548	1,0568	1,0593	1,0602	1,0617	1,0637	1,0661
0,28	0,06154	1,3201	1,3232	1,3257	1,3287	1,3300	1,3318	1,3343	1,3374
0,30	0,07065	1,5154	1,5190	1,5218	1,5253	1,5267	1,5289	1,5317	1,5352
0,32	0,08038	1,7242	1,7283	1,7315	1,7355	1,7371	1,7395	1,7427	1,7467
0,36	0,10174	2,1822	2,1873	2,1914	2,1965	2,1985	2,2016	2,2056	2,2107
0,40	0,12560	2,6941	2,7004	2,7054	2,7117	2,7142	2,7180	2,7230	2,7293
0,45	0,1590	3,410	3,418	3,424	3,432	3,435	3,440	3,446	3,454
0,50	0,1963	4,210	4,219	4,227	4,237	4,241	4,247	4,255	4,265
0,56	0,2462	5,280	5,293	5,303	5,315	5,320	5,327	5,337	5,349
0,60	0,2826	6,062	6,076	6,087	6,101	Six thousand one hundred seven	6,115	6,127	6,141
0,70	0,3847	8,251	8,270	8,285	8,305	8,312	8,324	8,339	8,358
0,80	0,5024	10,776	10,802	10,822	10,847	10,857	10,872	10,892	10,917
0,85	0,5672	12,166	12,194	12,217	12,245	12,256	12,273	12,296	12,324
0,90	0,6359	13,639	13,671	13,696	13,728	13,741	13,760	13,785	13,817
Of 1.00	AZN 0.7850	16,838	16,878	16,909	16,948	16,964	16,987	17,019	17,058
1,10	0,9499	20,374	20,422	20,460	20,507	20,526	20,555	20,593	20,640
1,20	Seen at 1.1304	24,247	24,304	24,349	24,405	24,428	24,462	24,507	24,564
1,50	1,7663	37,886	37,974	38,045	38,133	38,169	38,222	38,292	38,381
1,60	2,0096	43,106	43,206	43,287	43,387	43,427	43,488	43,568	43,669
1,80	2,5434	54,556	54,683	54,785	54,912	54,963	55,039	55,141	55,268
Of 2.00	3,1400	67,353	67,510	67,636	67,793	67,855	67,950	68,075	68,232
2,20	3,7994	81,497	81,687	81,839	82,029	82,105	82,219	82,371	82,561
2,50	4,9063	105,239	105,484	105,681	105,926	106,024	106,171	106,368	106,613
2,80	6,1544	132,012	132,320	132,566	132,873	132,997	133,181	133,427	133,735
Of 3.00	7,0650	151,544	151,898	152,180	152,533	152,675	152,887	153,169	153,522
Of 4.00	12,5600	269,412	270,040	270,542	271,170	271,422	271,798	272,301	272,929
5,00	19,6250	420,956	421,938	422,723	423,704	424,096	424,685	425,470	426,451
6,00	28,2600	606,177	607,590	608,720	610,133	610,699	611,546	612,677	614,090

Continuation of table A. 1

Dia- meter Pro in Loki, mm	Square poperek- tion cross section, mm	Estimated weight of 1 m of wire, g
		Plrd 98−2	Plrd 95−5	Plrd 93−7	Plrd 92,5−7,5	Plrd 90−10	Plrd 80−20	Plrd 70−30	Plrd 60−40	Plpd 90−10
0,020	0,000314	0,00664	0,00650	0,00641	0,00639	0,00628	-	-	-	0,00626
0,022	0,000380	0,00803	0,00786	0,00776	0,00773	0,00760	-	-	-	0,00757
0,025	0,000491	0,01037	0,01016	0,01002	0,00998	0,00981	-	-	-	0,00978
0,028	0,000615	0,01301	0,01274	0,01257	0,01252	0,01231	-	-	-	0,01227
0,030	0,000707	0,01494	0,01462	0,01443	0,01438	0,01413	-	-	-	0,01408
0,032	0,000804	0,01699	0,01664	0,01641	0,01636	0,01608	-	-	-	0,01602
0,036	0,001017	0,02151	0,02106	0,02077	0,02070	0,02035	-	-	-	0,02028
0,040	0,001256	0,02655	0,02600	0,02565	0,02556	0,02512	0,02354	-	-	0,02503
0,045	0,001590	0,03360	0,03291	0,03246	0,03235	0,03179	0,02979	-	-	0,03168
0,050	0,001963	0,04149	0,04062	0,04007	0,03994	0,03925	0,03678	-	-	0,03911
0,056	0,002462	0,05204	0,05096	0,05027	0,05010	0,04924	0,04613	-	-	0,04906
0,060	0,002826	0,05974	0,05850	0,05771	0,05751	0,05652	0,05296	-	-	0,05632
0,070	0,003847	0,08132	0,07962	0,07855	0,07828	0,07693	0,07208	-	-	0,07666
0,080	0,005024	0,10621	0,10400	0,10259	0,10224	0,10048	0,09415	-	-	0,10013
0,090	0,006359	0,13442	0,13162	0,12984	0,12940	0,12717	0,11916	-	-	0,12672
0,10	0,00785	0,1659	0,1625	0,1603	0,1597	0,1570	0,1471	0,1384	0,1306	0,1565
0,11	0,00950	0,2008	0,1966	0,1940	0,1933	0,1900	0,1780	0,1675	0,1581	0,1893
0,12	0,01130	0,2390	0,2340	0,2308	0,2300	0,2261	0,2118	0,1993	0,1881	0,2253
0,14	0,01539	0,3253	0,3185	0,3142	0,3131	0,3077	0,2883	0,2713	0,2560	0,3066
0,15	0,01766	0,3734	0,3656	0,3607	0,3594	0,3533	0,3310	0,3114	0,2939	0,3520
0,16	0,00031	0,4248	0,4160	0,4104	0,4090	0,4019	0,3766	0,3543	0,3344	0,4005
0,18	0,02543	0,5377	0,5265	0,5194	0,5176	0,5087	0,4766	0,4484	0,4232	0,5069
0,20	0,03140	0,6638	0,6500	0,6412	0,6390	0,6280	0,5884	0,5536	0,5225	0,6258
0,22	0,03799	0,8032	At 0.7865	0,7758	0,7732	0,7599	Of 0.7120	0,6698	0,6322	0,7572
0,25	0,04906	1,0372	1,0156	1,0019	At 0.9984	0,9813	0,9194	0,8650	0,8164	0,9778
0,28	0,06154	1,3010	1,2740	1,2567	1,2524	1,2309	1,1533	1,0850	1,0241	1,2266
0,30	0,07065	1,4935	1,4625	1,4427	1,4377	1,4130	1,3240	1,2456	1,1756	1,4081
0,32	0,08038	1,6993	1,6639	1,6414	1,6358	1,6077	1,5064	1,4172	1,3376	1,6021
0,36	0,10174	2,1507	2,1059	2,0774	2,0703	2,0347	1,9065	1,7936	1,6929	2,0276
0,40	0,12560	2,6552	2,5999	2,5648	2,5560	2,5120	2,3537	2,2143	2,0900	2,5032
0,45	0,1590	3,360	3,291	3,246	3,235	3,179	2,979	2,803	2,645	3,168
0,50	0,1963	4,149	4,062	4,007	3,994	3,925	3,678	3,460	3,266	3,911
0,56	0,2462	5,204	5,096	5,027	5,010	4,924	4,613	4,340	4,096	4,906
0,60	0,2826	5,974	5,850	5,771	5,751	Five thousand six hundred fifty two	5,296	4,982	4,702	5,632
0,70	0,3847	8,132	7,962	7,855	7,828	7,693	7,208	6,781	6,401	7,666
0,80	0,5024	10,621	10,400	10,259	10,224	10,048	9,415	8,857	8,360	10,013
0,85	0,5672	11,990	11,740	11,581	11,542	11,343	10,629	9,999	9,438	11,304
0,90	0,6359	13,442	13,162	12,984	12,940	12,717	11,916	11,210	10,581	12,672
Of 1.00	AZN 0.7850	16,595	16,250	16,030	15,975	15,700	14,711	13,840	13,062	15,645
1,10	0,9499	20,080	19,662	19,396	19,329	18,997	17,800	16,746	15,806	18,931
1,20	Seen at 1.1304	23,897	23,399	23,083	23,004	22,608	21,184	19,929	18,810	22,529
1,50	1,7663	37,339	36,561	36,067	35,943	35,325	33,100	31,139	29,390	35,201
1,60	2,0096	42,483	41,599	41,036	40,895	40,192	37,660	35,429	33,440	40,051
1,80	2,5434	53,767	52,648	51,936	51,758	50,868	47,663	44,840	42,322	50,690
Of 2.00	3,1400	66,380	64,998	64,119	63,899	62,800	58,844	55,358	52,250	62,580
2,20	3,7994	80,32	78,65	77,58	77,32	75,99	71,20	66,98	63,22	75,72
2,50	4,9063	103,72	101,56	Of 100.19	99,84	98,13	91,94	Of 86.50	81,64	Of 97.78
2,80	6,1544	130,10	127,40	125,67	125,24	123,09	115,33	108,50	102,41	122,66
Of 3.00	7,0650	149,35	146,25	144,27	143,77	141,30	132,40	124,56	117,56	140,81
Of 4.00	12,5600	265,52	259,99	256,48	255,60	251,20	235,37	221,43	Of 209.00	250,32
5,00	19,6250	414,87	406,24	400,74	399,37	392,50	367,77	345,99	326,56	391,13
6,00	28,2600	597,42	584,98	577,07	575,09	565,20	529,59	498,22	470,25	563,22

Continuation of table A. 1

Dia- meter Pro in Loki, mm	Square poperek- tion cross section, mm	Estimated weight of 1 m of wire, g
		Plpd 85−15	Plpd 80−20	Plpdrd 92,5−4-3,5	Plpt-other 81−15−3,5−0,5	Plru 92−8	Plru 90−10	PLM 97,5	PLM 91,5	PLN 95,5
0,020	0,000314	0,00604	0,00584	0,00638	0,00589	-	0,00626	-	0,00602	-
0,022	0,000380	0,00731	0,00707	0,00772	0,00713	-	0,00758	-	0,00728	-
0,025	0,000491	0,00944	0,00913	0,00997	0,00920	-	0,00979	-	0,00941	-
0,028	0,000615	0,01185	0,01145	0,01251	0,01155	-	0,01228	-	0,01180	-
0,030	0,000707	0,01360	0,01315	0,01436	0,01325	-	0,01409	-	0,01354	-
0,032	0,000804	0,01547	0,01496	0,01633	0,01508	-	0,01604	-	0,01541	-
0,036	0,001017	0,01958	0,01893	0,02067	0,01909	-	0,02030	-	0,01950	-
0,040	0,001256	0,02418	0,02337	0,02552	0,02356	0,02542	0,02506	0,02604	0,02408	0,02533
0,045	0,001590	0,03060	0,02958	0,03230	0,02982	0,03217	0,03171	0,03295	0,03047	0,03206
0,050	0,001963	0,03778	0,03652	0,03988	0,03682	0,03972	0,03915	0,04068	0,03762	0,03958
0,056	0,002462	0,04739	0,04581	0,05002	0,04618	0,04983	0,04911	0,05103	0,04719	0,04965
0,060	0,002826	0,05440	0,05259	0,05742	0,05302	0,05720	0,05638	0,05858	0,05417	0,05700
0,070	0,003847	0,07405	0,07158	0,07816	0,07216	0,07785	0,07674	0,07974	0,07374	0,07758
0,080	0,005024	0,09671	0,09350	0,10209	0,09425	0,10169	0,10023	0,10415	0,09631	0,10133
0,090	0,006359	0,12240	0,11833	0,12920	0,11929	0,12870	0,12685	0,13181	0,12189	0,12825
0,10	0,00785	0,1511	0,1461	0,1595	0,1473	0,1589	0,1566	0,1627	0,1505	0,1583
0,11	0,00950	0,1828	0,1768	0,1930	0,1782	0,1922	0,1895	0,1969	0,1821	0,1916
0,12	0,01130	0,2176	0,2104	0,2297	0,2121	0,2288	0,2255	0,2343	0,2167	0,2280
0,14	0,01539	0,2962	0,2863	0,3126	0,2886	0,3114	0,3070	0,3190	0,2949	0,3103
0,15	0,01766	0,3400	0,3287	0,3589	0,3313	0,3575	0,3524	0,3661	0,3386	0,3563
0,16	0,00031	0,3868	0,3740	0,4084	0,3770	0,4067	0,4009	0,4166	0,3852	0,4053
0,18	0,02543	0,4896	0,4733	0,5168	0,4771	0,5148	0,5074	0,5272	0,4876	0,5130
0,20	0,03140	0,6045	0,5844	0,6380	0,5891	0,6355	0,6264	0,6509	0,6019	0,6333
0,22	0,03799	0,7314	0,7071	0,7720	0,7128	0,7690	0,7580	0,7876	0,7283	0,7663
0,25	0,04906	0,9445	0,9131	0,9970	0,9204	Around 0.9930	0,9788	1,0171	0,9405	0,9896
0,28	0,06154	1,1847	1,1453	Of 1.2506	1,1546	1,2457	1,2278	1,2758	1,1798	1,2413
0,30	0,07065	1,3600	1,3148	1,4356	1,3254	1,4300	1,4095	1,4646	1,3544	1,4250
0,32	0,08038	1,5474	1,4959	1,6334	1,5080	Of 1.6270	1,6037	1,6664	1,5410	1,6213
0,36	0,10174	1,9584	1,8933	2,0673	1,9086	2,0591	2,0296	2,1090	1,9503	2,0520
0,40	0,12560	2,4178	2,3374	2,5522	2,3563	2,5421	2,5057	2,6037	2,4078	2,5334
0,45	0,1590	3,060	2,958	3,230	2,982	3,217	3,171	3,295	3,047	3,206
0,50	0,1963	3,778	3,652	3,988	3,682	3,972	3,915	Four thousand sixty eight	3,762	3,958
0,56	0,2462	4,739	4,581	5,002	4,618	4,983	4,911	5,103	4,719	4,965
0,60	0,2826	5,440	5,259	5,742	5,302	5,720	5,638	5,858	5,417	5,700
0,70	0,3847	7,405	7,158	7,816	7,216	7,785	7,674	7,974	7,374	7,758
0,80	0,5024	9,671	9,350	10,209	9,425	10,169	10,023	10,415	9,631	10,133
0,85	0,5672	10,918	10,555	11,525	10,640	11,479	11,315	11,757	10,873	11,440
0,90	0,6359	12,240	11,833	12,920	11,929	12,870	12,685	13,181	12,189	12,825
Of 1.00	AZN 0.7850	15,111	14,609	15,951	14,727	15,888	15,661	16,273	15,048	15,833
1,10	0,9499	18,285	17,677	19,301	17,819	19,225	18,950	19,690	18,209	19,158
1,20	Seen at 1.1304	21,760	21,037	22,970	21,206	22,879	22,551	23,433	21,670	22,800
1,50	1,7663	34,000	32,870	35,890	33,135	35,749	35,237	36,614	33,859	35,625
1,60	2,0096	38,685	37,399	40,835	37,700	40,674	40,092	41,659	38,524	40,534
1,80	2,5434	48,960	47,333	51,682	47,714	51,478	50,741	52,725	48,757	51,300
Of 2.00	3,1400	60,445	58,435	63,805	58,906	63,554	62,643	65,092	60,194	63,334
2,20	3,7994	73,14	70,71	77,20	Of 71.28	76,90	75,80	78,76	72,83	Of 76.63
2,50	4,9063	Of 94.45	91,31	99,70	92,04	99,30	97,88	101,71	94,05	98,96
2,80	6,1544	118,47	114,53	125,06	At 115.46	124,57	122,78	127,58	117,98	124,13
Of 3.00	7,0650	Of 136.00	131,48	143,56	132,54	Of 143.00	140,95	146,46	135,44	Of 142.50
Of 4.00	12,5600	241,78	233,74	255,22	235,63	254,21	250,57	260,37	240,78	253,34
5,00	19,6250	377,78	365,22	398,78	368,17	397,21	391,52	406,83	376,21	395,84
6,00	28,2600	544,01	525,92	574,24	530,16	571,98	563,79	585,83	541,74	Of 570.00

Annex B (reference). Electric resistance wire made of platinum and alloys on its basis

Appendix B
(reference)

Table B. 1

Dia- meter Pro in Loki, mm	Square poperek- tion cross section, mm	Electrical resistance of 1 m of wire, Ohm
		PL 99, and 93; PL 99,9; PL 99,8	PLI 95−5, Plpd 90−10, Plpdrd 92,5−4-3,5, Plrd 70−30	PLI 90−10	PLI 85−15	PLI of 82.5 to 17.5	PLI 80−20	PLI 75−25	PLI 70−30
0,10	0,00785	14,013	24,204	30,573	36,943	39,490	40,764	42,038	43,312
0,11	0,0095	11,581	20,003	25,267	30,531	32,637	33,690	34,742	35,795
0,12	0,0113	9,731	16,808	21,231	25,655	27,424	28,309	29,193	Thirty thousand seventy eight
0,14	0,0154	7,149	12,349	15,599	18,848	20,148	20,798	21,448	22,098
0,15	0,0177	6,228	10,757	13,588	16,419	17,551	18,117	18,684	19,250
0,16	0,0201	5,474	9,455	11,943	14,431	15,426	15,924	16,421	16,919
0,18	Or 0.0254	4,325	7,470	9,436	11,402	12,188	12,582	12,975	13,368
0,20	0,0314	3,503	6,051	7,643	9,236	9,873	10,191	10,510	10,828
0,22	0,0380	2,895	5,001	6,317	7,633	8,159	8,422	8,686	8,949
0,25	0,0491	2,242	3,873	4,892	5,911	6,318	6,522	6,726	6,930
0,28	0,0615	1,787	3,087	3,900	4,712	5,037	5,200	5,362	5,525
0,30	0,0707	1,557	2,689	3,397	4,105	4,388	4,529	4,671	4,812
0,32	0,0804	1,368	2,364	2,986	3,608	3,856	3,981	4,105	4,230
0,36	0,1017	1,081	1,868	2,359	2,851	3,047	3,145	3,244	3,342
0,40	0,1256	0,8758	1,5127	1,9108	2,3089	2,4682	2,5478	2,6274	2,7070
0,45	0,1590	0,6920	1,1953	1,5098	1,8243	1,9501	2,0131	2,0760	2,1389
0,50	0,1963	0,5605	0,9682	1,2229	1,4777	1,5796	1,6306	1,6815	1,7325
0,56	0,2462	0,4468	0,7718	0,9749	1,1780	1,2593	1,2999	1,3405	1,3811
0,60	0,2826	0,3892	0,6723	0,8493	1,0262	1,0970	Of 1.1323	1,1677	1,2031
0,70	0,3847	0,2860	0,4940	0,6239	0,7539	0,8059	0,8319	0,8579	Of 0.8839
0,80	0,5024	0,2189	0,3782	0,4777	0,5772	0,6170	0,6369	0,6568	0,6768
0,85	0,5672	0,1939	0,3350	0,4232	0,5113	0,5466	0,5642	0,5818	0,5995
0,90	0,6359	0,1730	0,2988	0,3774	0,4561	0,4875	0,5033	0,5190	0,5347
Of 1.00	AZN 0.7850	0,1401	0,2420	0,3057	0,3694	0,3949	0,4076	0,4204	0,4331
1,10	0,9499	0,1158	Of 0.2000	0,2527	0,3053	0,3264	0,3369	0,3474	0,3580
1,20	Seen at 1.1304	0,0973	0,1681	0,2123	0,2565	0,2742	0,2831	0,2919	0,3008
1,50	1,7663	0,0623	0,1076	0,1359	0,1642	0,1755	0,1812	0,1868	0,1925
1,60	2,0096	0,0547	0,0945	0,1194	0,1443	0,1543	0,1592	0,1642	0,1692
1,80	2,5434	0,0432	0,0747	0,0944	0,1140	0,1219	0,1258	0,1297	0,1337
Of 2.00	3,1400	0,0350	0,0605	0,0764	0,0924	0,0987	0,1019	0,1051	0,1083
2,20	3,7994	0,0290	Of 0.0500	0,0632	0,0763	0,0816	0,0842	0,0869	0,0895
2,50	4,9063	0,0224	0,0387	0,0489	0,0591	0,0632	0,0652	0,0673	0,0693
2,80	6,1544	0,0179	0,0309	0,0390	0,0471	0,0504	0,0520	0,0536	0,0552
Of 3.00	7,0650	0,0156	0,0269	0,0340	0,0410	0,0439	0,0453	0,0467	0,0481
Of 4.00	12,5600	0,0088	0,0151	0,0191	0,0231	0,0247	0,0255	0,0263	0,0271
5,00	19,6250	0,0056	0,0097	0,0122	0,0148	0,0158	0,0163	0,0168	0,0173
6,00	28,2600	0,0039	0,0067	0,0085	0,0103	0,0110	0,0113	0,0117	0,0120

End of table B. 1

Dia- meter Pro in Loki, mm	Square poperek- tion cross section, mm	Electrical resistance of 1 m of wire, Ohm
		Plrd 93−7; Plrd 92,5−7,5; Plrd 60−40	Plrd 90−10, Plrd 80−20	Plpd 85−15; PLN 95,5−4,5	Plpd 80−20	Plru 92−8	Plru 90−10	PLM 97,5	PLM 91,5
0,10	0,00785	22,930	25,478	28,025	31,847	48,408	52,229	38,217	71,338
0,11	0,0095	18,950	21,056	23,162	26,320	40,006	43,165	31,584	58,957
0,12	0,0113	15,924	17,693	19,462	22,116	33,616	36,270	26,539	49,540
0,14	0,0154	11,699	12,999	14,299	16,249	24,698	26,648	19,498	36,397
0,15	0,0177	10,191	11,323	12,456	14,154	21,515	23,213	16,985	31,706
0,16	0,0201	8,957	9,952	10,947	12,440	18,909	20,402	14,928	27,866
0,18	Or 0.0254	7,077	7,863	8,650	9,829	14,941	16,120	11,795	22,018
0,20	0,0314	5,732	6,369	7,006	7,962	12,102	13,057	9,554	17,834
0,22	0,0380	4,738	5,264	5,790	6,580	10,002	10,791	7,896	14,739
0,25	0,0491	3,669	4,076	4,484	5,096	7,745	8,357	6,115	11,414
0,28	0,0615	2,925	3,250	3,575	4,062	6,174	6,662	4,875	9,099
0,30	0,0707	2,548	2,831	3,114	3,539	5,379	5,803	Of 4.246	7,926
0,32	0,0804	2,239	2,488	2,737	3,110	4,727	5,101	3,732	6,967
0,36	0,1017	1,769	1,966	2,162	2,457	3,735	4,030	2,949	5,504
0,40	0,1256	1,4331	1,5924	1,7516	1,9904	3,0255	3,2643	2,3885	4,4586
0,45	0,1590	Of 1.1323	1,2582	1,3840	1,5727	2,3905	2,5792	1,8872	3,5228
0,50	0,1963	0,9172	1,0191	1,1210	1,2739	1,9363	2,0892	1,5287	2,8535
0,56	0,2462	0,7312	0,8124	0,8937	1,0155	1,5436	1,6655	1,2186	2,2748
0,60	0,2826	0,6369	0,7077	0,7785	0,8846	1,3447	1,4508	1,0616	1,9816
0,70	0,3847	0,4680	0,5200	0,5719	0,6499	0,9879	1,0659	0,7799	1,4559
0,80	0,5024	0,3583	0,3981	0,4379	0,4976	0,7564	0,8161	0,5971	1,1146
0,85	0,5672	0,3174	0,3526	0,3879	0,4408	0,6700	0,7229	0,5289	0,9874
0,90	0,6359	0,2831	0,3145	0,3460	0,3932	0,5976	0,6448	0,4718	0,8807
Of 1.00	AZN 0.7850	0,2293	0,2548	0,2803	0,3185	0,4841	0,5223	0,3822	0,7134
1,10	0,9499	0,1895	0,2106	0,2316	0,2632	0,4001	0,4316	0,3158	0,5896
1,20	Seen at 1.1304	0,1592	0,1769	0,1946	0,2212	0,3362	0,3627	0,2654	0,4954
1,50	1,7663	0,1019	0,1132	0,1246	0,1415	0,2151	0,2321	0,1699	0,3171
1,60	2,0096	0,0896	0,0995	0,1095	0,1244	0,1891	0,2040	0,1493	0,2787
1,80	2,5434	0,0708	0,0786	0,0865	0,0983	0,1494	0,1612	0,1180	0,2202
Of 2.00	3,1400	0,0573	0,0637	0,0701	0,0796	0,1210	0,1306	0,0955	0,1783
2,20	3,7994	0,0474	0,0526	0,0579	0,0658	0,1000	0,1079	0,0790	0,1474
2,50	4,9063	0,0367	0,0408	0,0448	0,0510	0,0775	0,0836	0,0611	0,1141
2,80	6,1544	0,0292	0,0325	0,0357	0,0406	0,0617	0,0666	0,0487	0,0910
Of 3.00	7,0650	0,0255	0,0283	0,0311	0,0354	0,0538	0,0580	0,0425	0,0793
Of 4.00	12,5600	0,0143	0,0159	0,0175	0,0199	0,0303	0,0326	0,0239	0,0446
5,00	19,6250	0,0092	0,0102	0,0112	0,0127	0,0194	0,0209	0,0153	0,0285
6,00	28,2600	0,0064	0,0071	0,0078	0,0088	0,0134	0,0145	0,0106	0,0198
Note — determine the Electrical resistance of the wire in soft (annealed) state.

Annex b (informative). The physical properties of the wire made of platinum and alloys on its basis

The App
(reference)

Table B. 1

Mark platinum (the alloy based on it)	Rupture strength of wire , MPa (kgs/mm)		Specific electric as the resistance of Ohm·mm/m	Temperature- tion coefficients the patient elec- electric Modul and triggers the fight- niya (TCAS) ·10
	soft	solid
PL 99, and 93; PL 99,9; PL 99,8	120−200 (12−20)	340−690 (35−70)	0,11	3,9
PLI 95−5	200−290 (20−30)	440−740 (45−75)	0,19	1,9
PLI 90−10	290−390 (30−40)	540−830 (55−85)	0,24	1,3
PLI 85−15	440−640 (45−65)	830−1130 (85−115)	0,29	1,0
PLI of 82.5 to 17.5	590−690 (60−70)	880−1130 (90−115)	0,31	0,9
PLI 80−20	590−740 (60−75)	930−1130 (95−115)	0,32	0,9
PLI 75−25	685−830 (70−85)	980−1225 (100−125)	0,33	0,8
PLI 70−30	880−1080 (90−110)	1180−1470 (120−150)	0,34	0,7
Plrd 98−2	200−290 (20−30)	440−740 (45−75)	0,17	2,1
Plrd 95−5	250−340 (25−35)	490−740 (50−75)	0,18	1,9
Plrd 93−7	290−390 (30−40)	540−740 (55−75)	0,18	1,9
Plrd 92,5−7,5	290−390 (30−40)	540−740 (55−75)	0,18	1,8
Plrd 90−10	290−390 (30−40)	540−740 (55−75)	0,20	1,7
Plrd 80−20	390−490 (40−50)	780−980 (80−100)	0,20	1,4
Plrd 70−30	440−590 (45−60)	780−1080 (80−110)	0,19	1,3
Plrd 60−40	540−640 (55−65)	980−1270 (100−130)	0,18	1,4
Plpd 90−10	150−250 (15−25)	290−440 (30−45)	0,19	1,8
Plpd 85−15	150−250 (15−25)	290−440 (30−45)	0,22	1,5
Plpd 80−20	200−290 (20−30)	340−490 (35−50)	0,25	1,3
Plpdrd 92,5−4-3,5	250−290 (25−30)	490−735 (50−75)	0,19	1,9
Plpdrdru 81−15−3,5−0,5	290−390 (30−40)	540−780 (55−80)	0,21	1,8
Plru 92−8	590−690 (60−70)	880−1270 (90−130)	0,38	0,6
Plru 90−10	590−690 (60−70)	980−1470 (100−150)	0,41	0,5
PLM 97,5	390−540 (40−55)	590−1080 (60−90)	0,30	1,0
PLM 91,5	490−640 (50−65)	1080−1270 (90−130)	0,56	0,4
PLN 95,5	490−640 (50−65)	1080−1270 (90−130)	0,22	2,1
Notes 1 electrical resistivity and TCAS (average value) is determined on the wire in soft (annealed) state. 2 ultimate strength, and electrical resistivity determined on the wire.