GOST 617-2006

• gost-617-2006.pdf (945.09 KiB)
  ГОСТ 617-2006

GOST 617−2006 Pipe copper and brass round section General purpose. Specifications (with Change No. 1)

GOST 617−2006

Group B64

INTERSTATE STANDARD

PIPES COPPER AND BRASS ROUND SECTION GENERAL PURPOSE

Specifications

General-purpose copper and brass tubes of round section. Specifications

ISS 23.040.15
GST 18 4450

Date of introduction 2008−01−01

Preface

Goals, basic principles and main procedure of works on interstate standardization have been established in GOST 1.0−92 «interstate standardization system. Basic provisions» and GOST 1.2−97 «interstate standardization system. Interstate standards, rules and recommendations on interstate standardization. The procedure of development, adoption, application, renewal and cancellation"

Data on standard

1 DEVELOPED by the Technical Committee for standardization TC 106 «Tsvetmetprokat», Scientific-research, project and design Institute for alloys and processing of nonferrous metals «joint-stock company «Institute tsvetmetobrabotka» (JSC «Institute tsvetmetobrabotka»)

2 SUBMITTED by the Technical Secretariat of the Interstate Council for standardization, Metrology and certification

3 ACCEPTED by the Interstate Council for standardization, Metrology and certification (Protocol No. 29 of June 24, 2006)

The standard was accepted by voting:

4 by Order of the Federal Agency for technical regulation and Metrology dated December 27, 2006 No. 495-St inter-state standard GOST 617−2006 introduced as a national standard of the Russian Federation from January 1, 2008

5 REPLACE GOST 617−90


Information about introduction in action (termination) of this standard is published in the index «National standards».

Information about the amendments to this standard is published in the index «National standards», and the text changes — in the information sign «National standards». In case of revision or cancellation of this standard the appropriate information will be published in the information index «National standards»

The Change N 1, approved and promulgated by the Order of Rosstandart on 30.12.2013 N 2406-St c 01.09.2014

Change No. 1 made by the manufacturer of the database in the text ICS N 7, 2014

1 Scope

This standard applies to copper and brass (brass brand l96) cold-drawn and extruded round tubes sections for General use.

The standard specifies the dimensions, technical requirements, acceptance rules, methods of control and testing, packaging, labeling, transportation and storage of pipes.

2 Normative references

This standard uses the regulatory references to the following international standards:

GOST 427−75 Rulers measuring metal. Specifications

GOST 859−2001 Copper. Brand

GOST 1173−2006 of copper Strip. Specifications

GOST 1652.1−77 (ISO 1554−76) Alloys copper-zinc. Methods for determination of copper

GOST 1652.2−77 (ISO 4749−84) Alloys copper-zinc. Methods for determination of lead

GOST 1652.3−77 (ISO 1812−76, ISO 4748−84) Alloys copper-zinc. Methods of iron determination

GOST 1652.4−77 Alloys copper-zinc. Methods for determination of manganese

GOST 1652.5−77 (ISO 4751−84) Alloys copper-zinc. Methods for determination of tin

GOST 1652.6−77 Alloys copper-zinc. Methods for determination of antimony

GOST 1652.7−77 Alloys copper-zinc. Methods for determination of bismuth

GOST 1652.8−77 Alloys copper-zinc. Methods for determination of arsenic

GOST 1652.9−77 (ISO 7266−84) Alloys copper-zinc. Method for the determination of sulfur

GOST 1652.10−77 Alloys copper-zinc. Methods for determination of aluminium

GOST 1652.11−77 (ISO 4742−84) Alloys copper-zinc. Methods for determination of Nickel

GOST 1652.12−77 Alloys copper-zinc. Methods for determination of silicon

GOST 1652.13−77 Alloys copper-zinc. Methods for determination of phosphorus

GOST 2991−85 wooden disposable Boxes for loads up to 500 kg. General specifications

GOST 2999−75 Metals and alloys. Method of measurement of hardness by Vickers

The Wire GOST 3282−74 General purpose low carbon steel. Specifications

GOST 3560−73 package steel Strip. Specifications

GOST 3845−75 Pipe metal. Test method hydraulic pressure

GOST 6507−90 Micrometers. Specifications

GOST 7376−89* corrugated Cardboard. General specifications
______________
* On the territory of the Russian Federation GOST R 52901−2007 «corrugated Cardboard for packaging products. Technical conditions».

GOST 7502−98 metallic measuring tape. Specifications

GOST 8695−75 Pipe. Test method for flattening

GOST 9557−87 flat wooden Pallet size 800x1200 mm. specifications

GOST 9716.1−79 Alloy copper and zinc. Method of spectral analysis on a metal standard samples with photographic registration of spectrum

GOST 9716.2−79 Alloy copper and zinc. Method of spectral analysis on a metal standard samples with photoelectric registration of spectrum

GOST 9716.3−79 Alloy copper and zinc. Method of spectral analysis on the oxide samples with photographic registration of spectrum

GOST 9717.1−82 Copper. Method of spectral analysis on a metal standard samples with photoelectric registration of spectrum

GOST 9717.2−82 Copper. Method of spectral analysis on a metal standard samples with photographic registration of spectrum

GOST 9717.3−82 Copper. Method of spectral analysis of oxide standard specimens

GOST 10006−80 (ISO 6892−84) of the Pipe metal. Test method tensile

GOST 10198−91 wooden Boxes for goods of mass over 200 up to 20000 kg. General specifications

GOST 12082−82 wooden Crates for loads weighing up to 500 kg. General specifications

GOST 13938.1−78 Copper. Methods for determination of copper

GOST 13938.2−78 Copper. Methods of determining sulphur

GOST 13938.3−78 Copper. Method of determination of phosphorus

GOST 13938.4−78 Copper. Methods of iron determination

GOST 13938.5−78 Copper. Methods for determination of zinc

GOST 13938.6−78 Copper. Methods for determination of Nickel

GOST 13938.7−78 Copper. Methods for determination of lead

GOST 13938.8−78 Copper. Methods for determination of tin

GOST 13938.9−78 Copper. Methods for determination of silver

GOST 13938.10−78 Copper. Methods for determination of antimony

GOST 13938.11−78 Copper. Method for the determination of arsenic

GOST 13938.12−78 Copper. Methods for determination of bismuth

GOST 13938.13−93 Copper. Methods for determination of oxygen

GOST 13938.15−88 Copper. Methods for determination of chromium and cadmium

GOST 14192−96 Marking of cargo

GOST 15102−75 the universal metal closed Container of nominal gross mass 5,0 t Technical specifications

GOST 15467−79 quality Control of products. Basic concepts. Terms and definitions

GOST 15527−2004 Alloys copper-zinc (brass) pressure treated. Brand

GOST 15846−2002 Products that are sent to the far North regions and equated areas. Packing, marking, transportation and storage

GOST 18242−72* Statistical acceptance inspection by alternative feature. Plans control
________________
* On the territory of the Russian Federation GOST R 50779.71−99** (ISO 2859−1-89) «Statistical methods. Procedure sampling on alternative grounds. Part 1. Sampling plans consistent parties on the basis of acceptable quality level AQL».

** On the territory of the Russian Federation GOST R ISO 2859−1-2007. — Note the manufacturer’s database.

GOST 18321−73 Statistical quality control. Methods of random selection of piece products

GOST 21650−76 means of fastening of package cargoes in transport packages. General requirements

GOST 22225−76 universal Containers with a gross weight 0,625 and 1,25 t. specifications

GOST 24047−80 Semi-finished products from nonferrous metals and their alloys. Sampling for tensile test

GOST 24231−80 non-ferrous metals and alloys. General requirements to selection and preparation of samples for chemical analysis

GOST 24597−81 the packaged goods. Basic parameters and dimensions

GOST 26877−91 metal Products. Methods of measuring form deviations of

Note — When using this standard appropriate to test the effect of reference standards in the information system of General use — on the official website of the Federal Agency for technical regulation and Metrology on the Internet or published annually by the information sign «National standards» published as on January 1 of the current year and related information published monthly indexes published in the current year. If the reference standard is replaced (changed), when using this standard should be guided by replacing (amended) standard. If the reference standard is cancelled without replacement, then the situation in which the given link applies to the extent that does not affect this link.


(Changed edition, Rev. N 1).

3 Terms and definitions

This standard applies the following terms with respective definitions:

3.1 the seamless round tube: a Hollow product of round in cross section, having a uniform nominal wall thickness, which at all stages of production has a continuous circumference.

3.2 round welded tube: a Hollow product of round in cross section, having a uniform nominal wall thickness, are manufactured by longitudinally welding the rolled workpiece.

3.3 average diameter: arithmetic mean of maximal and minimal values of the diameters measured at one cross section perpendicular to the tube axis.

3.4 out-of-roundness (deviation from circular shape): Difference between the largest and smallest values of the diameters measured at one cross section perpendicular to the tube axis.

3.5 nominal wall thickness: wall Thickness specified in the order.

3.6 raznoshennoy (thickness variation, the deviation from concentricity): the difference between the largest and smallest values of wall thickness measured in single cross-section perpendicular to the tube axis.

3.7 the Bay Segment of the product wound into a series of continuous turns.

3.7.1 Bay freespool: the Bay in which the disordered coils held close to each other.

3.7.2 Bay layered orderly winding: the Bay in which the coils are wound in layers parallel to the axis of the Bay in such a way that the successive turns in each layer come one after the other.

3.7.3 Bay flat spiral winding: the Bay in which the product is wound spirally in the disc-shaped layer. Depending on the length of the pipe, this Bay may have multiple layers.

3.8 measuring length: Specific length of the product with the established length tolerance given in order for straight line segments or bays.

(Changed edition, Rev. N 1).

3.9 times the length: the Period of integral multiple of the number of core length with an allowance for cutting and a tolerance on the overall length.

3.10 random length: the length of the product within the specified range or not less than the specified value.

(Added, Rev. N 1).

4 Assortment

4.1 Geometrical dimensions of the pipes are determined by the outer diameter, wall thickness and length.

4.2 By agreement between the consumer and the manufacturer of the pipe can be specified inside diameter. In this case, the permissible deviations at the inner diameter needs to be agreed with the manufacturer.

4.3 Diameter cold-drawn pipes and tolerances for diameter shall be as specified in table 1.


Table 1 — nominal outside diameter cold-drawn pipe and limit deviations of the diameter

In millimeters

4.4 By agreement between the consumer and the manufacturer of the pipe can be manufactured with extreme deviation by the average diameter shown in table 2.


Table 2 — nominal outside diameter cold-drawn pipes, maximum deviations by the average diameter and the roundness of the pipe in segments

In millimeters

4.5 the diameter of the extruded pipe and the tolerances for diameter shall be as specified in table 3.


Table 3 — nominal outside diameter extruded tubes and limit deviations of the diameter

In millimeters

4.6 wall Thickness cold-drawn tubes and limit deviations for wall thickness shall be as specified in table 4.


Table 4 — nominal wall thickness cold-drawn tubes and limit deviations for wall thickness

In millimeters

Allowed production of tubes with intermediate values of wall thickness for which the maximum permissible deviations are accepted at most nearest value of the wall thickness.

4.7 At the request of the consumer and the manufacturer tolerances for the wall thickness can be expressed as a percentage of the thickness. Maximum deviations in percent of the wall thickness cold drawn pipe specified in table 5.


Table 5 — Thickness of the wall of the cold pipes and the maximum percentage deviation of the thickness

4.8 wall Thickness of extruded pipe and limit deviations for wall thickness shall be as specified in table 6.

Table 6 — nominal wall thickness of extruded pipe and limit deviations for wall thickness

In millimeters

It is possible to produce extruded pipes with intermediate values of wall thickness for which the maximum permissible deviations are taken to the nearest larger value of the wall thickness.

(Changed edition, Rev. N 1).