GOST 2624-2016
GOST 2624−2016 Tube capillary copper and brass. Technical specifications (with Amendment)
GOST 2624−2016
INTERSTATE STANDARD
COPPER AND BRASS TUBES, CAPILLARY
Specifications
Capillary copper and brass tubes. Specifications
ISS 23.040.15*
________________
* Amendment (IUS N 6−2017)
Date of introduction 2017−04−01
Preface
Goals, basic principles and main procedure of works on interstate standardization have been established in GOST 1.0−2015 «interstate standardization system. Basic provisions» and GOST 1.2−2015 «interstate standardization system. Interstate standards, rules and recommendations on interstate standardization. Rules of development, adoption, renewal and cancellation"
Data on standard
1 DEVELOPED by the Technical Committee for standardization TC 106 «Tsvetmetprokat», Scientific-research, project and design Institute for alloys and processing of nonferrous metals Joint-stock company «Institute tsvetmetobrabotka» (JSC «Institute tsvetmetobrabotka»)
2 as AMENDED by the Federal Agency for technical regulation and Metrology (Rosstandart)
3 ACCEPTED by the Interstate Council for standardization, Metrology and certification (Protocol dated February 29, 2016 N 85-P)
The adoption voted:
4 by Order of the Federal Agency for technical regulation and Metrology, dated 22 August 2016 N 930-St inter-state standard GOST 2624−2016 introduced as a national standard of the Russian Federation from April 1, 2017
5 REPLACE GOST 2624−77
6 REISSUE. April 2017
Information about the changes to this standard is published in the annual reference index «National standards», and the text changes and amendments — in monthly information index «National standards». In case of revision (replacement) or cancellation of this standard a notification will be published in the monthly information index «National standards». Relevant information, notification and lyrics are also posted in the information system of General use — on the official website of the Federal Agency for technical regulation and Metrology on the Internet (www.gost.ru)
AMENDED, published in IMS No. 6, 2017
An amendment made by the manufacturer of the database
1 Scope
This standard applies to cold-drawn capillary tube of circular cross section made of copper and brass used in propose hypersound or ultras and instrumentation and refrigeration equipment.
The requirements of this standard in terms of tube sizes (section 4) is mandatory.
The standard specifies the dimensions, technical requirements, acceptance rules, methods of control and testing, marking, packaging, transportation and storage tubes.
2 Normative references
This standard uses the regulatory references to the following international standards:
GOST 859−2014 Copper. Brand
GOST 1652.1−77 (ISO 1554−76) Alloys copper-zinc. Methods for determination of copper
GOST 1652.2−77 (ISO 4749−84) Alloys copper-zinc. Methods for determination of lead
GOST 1652.3−77 (ISO 1812−76, ISO 4748−84) Alloys copper-zinc. Methods of iron determination
GOST 1652.4−77 Alloys copper-zinc. Methods for determination of manganese
GOST 1652.5−77 (ISO 4751−84) Alloys copper-zinc. Methods for determination of tin
GOST 1652.6−77 Alloys copper-zinc. Methods for determination of antimony
GOST 1652.7−77 Alloys copper-zinc. Methods for determination of bismuth
GOST 1652.8−77 Alloys copper-zinc. Methods for determination of arsenic
GOST 1652.9−77 (ISO 7266−84) Alloys copper-zinc. Methods of determining sulphur
GOST 1652.10−77 Alloys copper-zinc. Methods for determination of aluminium
GOST 1652.11−77 (ISO 4742−84) Alloys copper-zinc. Methods for determination of Nickel
GOST 1652.12−77 Alloys copper-zinc. Methods for determination of silicon
GOST 1652.13−77 Alloys copper-zinc. Methods for determination of phosphorus
GOST 2228−81 Paper sack. Specifications
GOST 2405−88 pressure Gauges, vacuum gauges, pressure-vacuum gage, naphrameru, draft gauges and tranporter. General specifications
GOST 2991−85 wooden disposable Boxes for loads up to 500 kg. General specifications
The Wire GOST 3282−74 General purpose low carbon steel. Specifications
GOST 3560−73 package steel Strip. Specifications
GOST 3728−78 Pipe. Test method for bend
GOST 6507−90 Micrometers. Specifications
GOST 8828−89 base Paper and paper double-layer waterproof packaging. Specifications
GOST 9557−87 flat wooden Pallet size of 8001200 mm. Technical specifications
GOST 9569−2006 waxed Paper. Specifications
GOST 9717.2−82 Copper. Method of spectral analysis on a metal standard samples with photographic registration of spectrum
GOST 9717.3−82 Copper. Method of spectral analysis of oxide standard specimens
GOST 9932−75 lighting fixtures, glass, laboratory. Specifications
GOST 10006−80 (ISO 6892−84) of the Pipe metal. Test method tensile
GOST 13938.11−2014 Copper. Method for the determination of arsenic
GOST 13938.13−93 Copper. Methods for determination of oxygen
GOST 14192−96 Marking of cargo
GOST 15102−75 the universal metal closed Container of nominal gross mass 5,0 t Technical specifications
GOST 15527−2004 Alloys copper-zinc (brass) pressure treated. Brand
GOST 15846−2002 Products that are sent to the far North regions and equated areas. Packing, marking, transportation and storage
GOST 18242−72 Statistical acceptance inspection by alternative feature. Plans control
_______________
On the territory of the Russian Federation GOST R ISO 2859−1-2007"Statistical methods. Procedure sampling on alternative grounds. Part 1. Sampling plans consistent parties on the basis of an acceptable level of quality."
GOST 18321−73 Statistical quality control. Methods of random selection of piece products
GOST 18477−79 Containers are universal. The types, basic parameters and dimensions
GOST 24231−80 non-ferrous metals and alloys. General requirements to selection and preparation of samples for chemical analysis
GOST 24597−81 the packaged goods. Basic parameters and dimensions
GOST 25086−2011 non-ferrous metals and their alloys. General requirements for methods of analysis
GOST 26663−85 transport Packs. Formation with the use of packaging. General technical requirements
GOST 27450−87 Tube of copper and copper-zinc alloys. Method of determining contamination of the inner surface
GOST 31382−2009 Copper. Methods of analysis
GOST 32597−2013 Copper and copper alloys. Types of defects of billets and semi-finished
Note — When using this standard appropriate to test the effect of reference standards in the information system of General use — on the official website of the Federal Agency for technical regulation and Metrology on the Internet or in the annual information index «National standards» published as on January 1 of the current year, and the editions of the monthly information index «National standards» for the current year. If the reference standard is replaced (changed), when using this standard should be guided by replacing (amended) standard. If the reference standard is cancelled without replacement, then the situation in which the given link applies to the extent that does not affect this link.
3 Terms and definitions
This standard applies the terminology according to GOST 32597, as well as the following terms with respective definitions:
3.1 tube: a Hollow product of round or polyhedral in cross section, having a uniform nominal wall thickness.
3.2 nominal wall thickness: wall Thickness specified in the order.
3.3 Bay: Cut product wound into a series of continuous turns right not mixed up in rows, with no sharp bends.
3.4 measuring length: Specific length of the product, specified in the order, straight leg, or in the Bay.
4 Assortment
4.1 Capillary tube are made of groups A and B. the scope of the tubes listed in Appendix A.
4.2 conditional Outer and inner diameters of the tubes of group A, as well as tolerances for outside diameter shall be as specified in table 1.
Table 1