GOST R 53464-2009
GOST R 53464−2009 Casting of metals and alloys. Dimensional tolerances, weight and machining allowances (with Amendments No. 1, 2)
GOST R 53464−2009
Group В83
NATIONAL STANDARD OF THE RUSSIAN FEDERATION
CASTING OF METALS AND ALLOYS
Dimensional tolerances, weight and machining allowances
Metal and alloy castings. Dimensions and mass tolerances and machining allowances
OKS 77.140.80
OKP 41 1000
Date of introduction 2010−07−01
Preface
The objectives and principles of standardization in the Russian Federation established by the Federal law of 27 December 2002 N 184-FZ «On technical regulation», and rules for the application of national standards of the Russian Federation — GOST R 1.0−2004 «Standardization in the Russian Federation. The main provisions"
Data on standard
1 DEVELOPED by the State educational institution of higher professional education «Moscow state technical University «MAMI"
2 SUBMITTED by the Technical Committee for standardization TC 252 «Foundry"
3 APPROVED AND put INTO EFFECT by the Federal Agency for technical regulation and Metrology dated December 9, 2009 N 610-St
4 INTRODUCED FOR THE FIRST TIME
Information about the changes to this standard is published in the annually issued reference index «National standards», and the text changes and amendments — in monthly indexes published information «National standards». In case of revision (replacement) or cancellation of this standard a notification will be published in a monthly information index «National standards». Relevant information, notification and lyrics are also posted in the information system of General use — on the official website of the Federal Agency for technical regulation and Metrology on the Internet
MADE: the Change in N 1, approved and promulgated by the Order of Rosstandart
Change N 1, 2 made by the manufacturer of the database in the text IUS N 2, 2012, ICS No. 6, 2013
1 Scope
This standard applies to the casting of ferrous and non-ferrous metals and alloys, and establishes tolerances of size, form, location and surface roughness, weight and machining allowances.
2 Normative references
This standard uses the regulatory references to the following standards:
GOST 2.308−79 unified system for design documentation. The indication on the drawings of tolerances of form and position of surfaces
GOST 3.1125−88 unified system of technical documentation. Rules of graphic elements run of molds and castings
GOST 8−82 metal-cutting Machine tools. General requirements for testing the accuracy
GOST 3212−92 Sets model. Slope forming, rod signs, dimensional tolerances
Note — When using this standard appropriate to test the effect of reference standards in the information system of General use — on the official website of the Federal Agency for technical regulation and Metrology on the Internet or published annually by the information sign «National standards» published as on January 1 of the current year and related information published monthly indexes published in the current year. If the reference standard is replaced (changed), when using this standard should be guided by replacing (amended) standard. If the reference standard is cancelled without replacement, then the situation in which the given link applies to the extent that does not affect this link.
3 Terms and definitions
This standard applies the following terms with respective definitions:
3.1 the nominal size of the part (casting): the Size specified on the detail drawing (casting).
3.2 the average size of items: Size of the part corresponding to the middle of the field of his admission.
(Changed edition, Rev. N 2).
3.3 dimensions of castings: a Collection of casting dimensions, characterized by similar structural and technological conditions for the formation of their accuracy.
Dimensions 1 — dimensions of the casting formed one part of a mold or a core.
The dimensions of the 2 sizes of castings and formed by two proformae or the drag and rod (including the dimensions of the facing plane of the connector casting or crossing it).
Dimensions 3 — dimensions of the castings formed by three or more parts of the mold, several bars, or moving form elements, and the thickness of the walls, which is the closing link in two sizes.
3.4 actual size of casting: the Actual size is measured point-to-point tool.
3.5 tolerance of displacement of the casting member in the plane of the connector: the difference between the extreme deviations of the provisions of the element parts of a casting formed in different proforma.
3.6 General tolerance item casting: a Comprehensive tolerance, including tolerance of size from the surface to the base and is independently assigned tolerances of form and arrangement of normalized surface area.
3.7 surface roughness: a Set of recurring irregularities of small magnitude (of asperities).
The baseline for determination of roughness parameters is the average line of the white surface. Accepted symbols: (mm) — arithmetical mean deviation of the white surfaces
(µm) is the height of the roughness (ten-point).
3.8 neravnomernosti surface: a Set of recurring irregularities average value (metoprolola), i.e. surface irregularities, a step higher than the base length, which measures the roughness of the surface.
The baseline for determining values of parameters of neravnomernosti is the average line profile of a surface.
The basic length for measuring neravnomernosti surfaces of castings shall be equal to 4−10 sampling lengths for the measurement of roughness, but at least five steps of neravnomernosti and not more than 100 mm.
Neravnomernosti occupies an intermediate position between surface roughness and form deviations of the surface.
3.9 tolerance neravnomernosti the casting surface: maximum height of metoprolola the casting surface, i.e. the sum of the greatest height of protrusion and depression surface.
3.10 allowance for processing: Thickness of the layer of metal removed from the casting surface when it is processed in order to ensure the specified size, shape, location, profnastila and roughness of the surface of the part.
3.11 General allowance: Total allowance for all transitions the processing corresponding to the middle of tolerance zones of parts and castings.
(Changed edition, Rev. N 2).
3.12 minimum casting allowance: the Allowance necessary to ensure the specified quality requirements (roughness, neravnomernosti and offered defect-free) surface of the part and independent of the thickness removed during the processing of the surface layer, roughness and neravnomernosti the casting surface. Surface defects castings shall not go beyond the minimum casting allowance.
3.13 the surface layer of the castings (parts): the Layer of metal with modified (at creation or upstream processing) composition, microstructure and properties, have increased resistance processing blade.
3.14 technological overlap: Local or uneven increase in body casting in comparison with the drawing of the cast part with the regulatory allowances for processing, due to the nature of the casting technology. To technological overlaps include: replenishment, providing directional crystallization of casting; replenish, smoothing the local indentations and protrusions; depositing and ties, compensating the distortion of the configuration of the casting under the influence of stresses generated during cooling; nonspillable holes; shrinkage rib; casting grades.
3.15 parameters of precision casting: General characteristics of dimensional accuracy, surfaces or casting in General.
The parameters of dimensional accuracy and surface castings include precision class, dimension, the degree of warpage of the casting member, the degree of accuracy of the surface and the displacement of the casting member and a number of mating surface of the casting.
Parameters precision casting as a whole include class dimensional accuracy degree of warping, the degree of accuracy of the surfaces and the accuracy class, as well as offset casting.
(Changed edition, Rev. N 2).
3.16 standards of precision casting: requirements for the level values of the parameters of precision castings.
Standards of accuracy set depending on the purpose, design and technological characteristics, operating conditions and manufacturing castings.
3.17 (Deleted, Rev. N 2).
4 General provisions
4.1 the nominal size of the casting should be taken equal to the nominal size of the part machined surfaces (figure 1) and the sum of the average part size and half the common stock on the treatment for machined surfaces in unilateral mating (figure 2) and bilateral allowance (such as bodies of rotation or mutually opposing surfaces) (figure 3).
— nominal size of the part;
is the nominal size of the casting;
— the minimum size of the casting;
— the maximum size of the casting;
— the total casting tolerance
Figure 1
— the General allowance;
,
,
,
,
— see figure 1
Figure 2
,
is the nominal size of the part, castings;
,
— the smallest and largest size of casting;
,
— see figures 1, 2
Figure 3
4.2 the Nominal mass of casting should be taken equal to the mass of castings with nominal sizes.
The method of determining the nominal mass set company standards.
4.3 When determining the minimum size of the casting take into account technological overlaps.
Technological overlaps set by the manufacturer and specifies the casting drawings or details indicating the size of the casting.
4.4 Standards of accuracy set on casting in General, its surface and dimensions.
4.5 Precision casting in General characterize a class of dimensional accuracy of the castings, the degree of warping, the degree of precision surfaces, accuracy class mass tolerance offset.
For machined castings shall specify the following provisions, all parameters of precision castings, machined castings are allowed to specify the degree of warpage of the casting. The use of other measures of accuracy of castings, and, if necessary, specific requirements for precision cast parts according to their purpose and operating conditions reglamentary in the standards of enterprises.
(Changed edition, Rev. N 2).
4.6 Standards of casting accuracy classes dimensional accuracy, degree of warping, the degree of precision surfaces, accuracy classes of mass, and a number of allowances for treatment for various technological processes and conditions of manufacture and processing of castings are given in appendices A-J.
On separate dimensions and the surface of the castings are allowed to set more stringent standards of accuracy than in General to casting.
4.7 In the drawing, casting (or drawing details the dimensions of the casting), you should specify a measurement base (base layout) and the base of the initial surface treatment.
5 Tolerances of size, form, location and roughness of the surfaces of castings
5.1 Tolerances of linear sizes of castings, variable and invariable treatment, should correspond to those in table 1. For the inclined, conical and shaped surfaces, defined by coordinates from one base or surface, allowed to set tolerances on the nominal value of the largest of sizes.
Table 1 — Tolerances linear dimensions of the casting
In millimeters
| Nominal size | The dimensional tolerance of the castings, not more, for accuracy classes | |||||||||||||||||||||
| 1 | 2 | 3T | 3 | 4 | 5T | 5 | 6 | 7T | 7 | 8 | 9T | 9 | 10 | 11T | 11 | 12 | 13t | 13 | 14 | 15 | 16 | |
| To 4 incl. |
0,06 | 0,08 | 0,10 | 0,12 | 0,16 | 0,20 | 0,24 | 0,32 | 0,40 | 0,50 | 0,64 | 0,80 | Of 1.00 | 1,20 | 1,60 | 2,0 | - | - | - | - | - | - |
| SV. 4 to 6 incl. |
0,07 | 0,09 | 0,11 | 0,14 | 0,18 | 0,22 | 0,28 | 0,36 | 0,44 | 0,56 | 0,70 | 0,90 | 1,10 | 1,40 | 1,8 | 2,2 | 2,8 | - | - | - | - | - |
| SV. 6 to 10 incl. |
0,08 | 0,10 | 0,12 | 0,16 | 0,20 | 0,24 | 0,32 | 0,40 | 0,50 | 0,64 | 0,80 | Of 1.00 | 1,20 | 1,60 | 2,0 | 2,4 | 3,2 | 4,0 | 5,0 | - | - | - |
| SV. 10 to 16 incl. |
0,09 | 0,11 | 0,14 | 0,18 | 0,22 | 0,28 | 0,36 | 0,44 | 0,56 | 0,70 | 0,90 | 1,10 | 1,40 | 1,8 | 2,2 | 2,8 | 3,6 | 4,4 | 5,6 | 7,0 | - | - |
| SV. 16 to 25 incl. |
0,10 | 0,12 | 0,16 | 0,20 | 0,24 | 0,32 | 0,40 | 0,50 | 0,64 | 0,80 | Of 1.00 | 1,20 | 1,60 | 2,0 | 2,4 | 3,2 | 4,0 | 5,0 | 6,4 | 8,0 | 10,0 | 12,0 |
| SV. 25 to 40 incl. |
0,11 | 0,14 | 0,18 | 0,22 | 0,28 | 0,36 | 0,44 | 0,56 | 0,70 | 0,90 | 1,10 | 1,40 | 1,8 | 2,2 | 2,8 | 3,6 | 4,4 | 5,6 | 7,0 | 9,0 | 11,0 | 14,0 |
| SV. 40 to 63 incl. |
0,12 | 0,16 | 0,20 | 0,24 | 0,32 | 0,40 | 0,50 | 0,64 | 0,80 | Of 1.00 | 1,20 | 1,60 | 2,0 | 2,4 | 3,2 | 4,0 | 5,0 | 6,4 | 8,0 | 10,0 | 12,0 | 16,0 |
| SV. 63 to 100 incl. |
0,14 | 0,18 | 0,22 | 0,28 | 0,36 | 0,44 | 0,56 | 0,70 | 0,90 | 1,10 | 1,40 | 1,8 | 2,2 | 2,8 | 3,6 | 4,4 | 5,6 | 7,0 | 9,0 | 11,0 | 14,0 | 18,0 |
| SV. 100 to 160 incl. |
0,16 | 0,20 | 0,24 | 0,32 | 0,40 | 0,50 | 0,64 | 0,80 | Of 1.00 | 1,20 | 1,60 | 2,0 | 2,4 | 3,2 | 4,0 | 5,0 | 6,4 | 8,0 | 10,0 | 12,0 | 16,0 | 20,0 |
| SV. 160 to 250 incl. |
- | - | 0,28 | 0,36 | 0,44 | 0,56 | 0,70 | 0,90 | 1,10 | 1,40 | 1,8 | 2,2 | 2,8 | 3,6 | 4,4 | 5,6 | 7,0 | 9,0 | 11,0 | 14,0 | 18,0 | 22,0 |
| SV. 250 to 400 incl. |
- | - | 0,32 | 0,40 | 0,50 | 0,64 | 0,80 | Of 1.00 | 1,20 | 1,60 | 2,0 | 2,4 | 3,2 | 4,0 | 5,0 | 6,4 | 8,0 | 10,0 | 12,0 | 16,0 | 20,0 | 24,0 |
| SV. 400 to 630 incl. |
- | - | - | - | 0,56 | 0,70 | 0,90 | 1,10 | 1,40 | 1,8 | 2,2 | 2,8 | 3,6 | 4,4 | 5,6 | 7,0 | 9,0 | 11,0 | 14,0 | 18,0 | 22,0 | 28,0 |
| SV. 630 to 1000 incl. |
- | - | - | - | - | 0,80 | Of 1.00 | 1,20 | 1,60 | 2,0 | 2,4 | 3,2 | 4,0 | 5,0 | 6,4 | 8,0 | 10,0 | 12,0 | 16,0 | 20,0 | 24,0 | 32,0 |
| SV. 1000 to 1600 incl. |
- | - | - | - | - | - | - | 1,40 | 1,8 | 2,2 | 2,8 | 3,6 | 4,4 | 5,6 | 7,0 | 9,0 | 11,0 | 14,0 | 18,0 | 22,0 | 28,0 | 36,0 |
| SV. 1600 to 2500 incl. |
- | - | - | - | - | - | - | - | 2,0 | 2,4 | 3,2 | 4,0 | 5,0 | 6,4 | 8,0 | 10,0 | 12,0 | 16,0 | 20,0 | 24,0 | 32,0 | 40,0 |
| SV. 2500 to 4000 incl. |
- | - | - | - | - | - | - | - | - | 2,8 | 3,6 | 4,4 | 5,6 | 7,0 | 9,0 | 11,0 | 14,0 | 18,0 | 22,0 | 28,0 | 36,0 | 44,0 |
| SV. 4000 to 6300 incl. |
- | - | - | - | - | - | - | - | - | 3,2 | 4,0 | 5,0 | 6,4 | 8,0 | 10,0 | 12,0 | 16,0 | 20,0 | 24,0 | 32,0 | 40,0 | 50,0 |
| SV. 6300 up to 10000 incl. |
- | - | - | - | - | - | - | - | - | - | - | - | 7,0 | 10,0 | 12,0 | 16,0 | 20,0 | 24,0 | 32,0 | 40,0 | 50,0 | 64,0 |
| SV. 10000 |
- | - | - | - | - | - | - | - | - | - | - | - | 8,0 | 12,0 | 16,0 | 20,0 | 24,0 | 32,0 | 40,0 | 50,0 | 64,0 | 80,0 |
5.2 dimensional Tolerances of the elements of the casting, formed by two proformae or the drag and rod (BP2), you should set the corresponding class dimension precision of casting. The dimensional tolerances are formed in one part of mold or one terminal (BP1) should be set for 1, 2 class more precisely. Dimensional tolerances formed by three or more parts of the mold, several bars, or moving form elements, and tolerances of wall thickness, which is the closing link in two sizes (BP3) should be set to 1, class 2 rougher (figure 4).
Size: BP1 — ,
,
,
; BP2 —
,
,
,
,
,
; BP3 —
,
,
,
Figure 4*
________________
* Changed the wording, Rev. N 2.
5.3 Tolerances linear dimensions of castings from pre-treated surface to the cast surface shall be within the tolerances specified in table 1. Classes their accuracy and designations in the drawings installed in the company standards.
5.4 Tolerances for angular dimensions in terms of linear dimensions must not exceed the values set out in table 1 for linear sizes of the respective classes of accuracy.
5.5 Tolerances the shape of the surfaces of the casting (deviations from straightness, flatness, parallelism, perpendicularity, profile) in the expression must correspond to those in table 2.
Table 2 — Tolerances of form, surfaces of castings
In millimeters
| The nominal size regulated plot | The form tolerance of the surface elements of the casting, not more, for the degrees of warpage of the elements of the casting | ||||||||||
| 1 | 2 | 3 | 4 | 5 | 6 | 7 | 8 | 9 | 10 | 11 | |
| To 125 incl. |
0,12 | 0,16 | 0,20 | 0,24 | 0,32 | 0,4 | 0,5 | 0,64 | 0,8 | 1,0 | 1,20 |
| SV. 125 to 160 a incl. |
0,16 | 0,20 | 0,24 | 0,32 | 0,4 | 0,5 | 0,64 | 0,8 | 1,0 | 1,20 | 1,6 |
| SV. 160 to 200 incl. |
0,20 | 0,24 | 0,32 | 0,4 | 0,5 | 0,64 | 0,8 | 1,0 | 1,20 | 1,6 | 2,0 |
| SV. 200 to 250 incl. |
0,24 | 0,32 | 0,4 | 0,5 | 0,64 | 0,8 | 1,0 | 1,20 | 1,6 | 2,0 | 2,40 |
| SV. 250 315 incl. |
0,32 | 0,4 | 0,5 | 0,64 | 0,8 | 1,0 | 1,20 | 1,6 | 2,0 | 2,40 | 3,2 |
| SV. 315 400 incl. |
0,4 | 0,5 | 0,64 | 0,8 | 1,0 | 1,20 | 1,6 | 2,0 | 2,40 | 3,2 | 4,0 |
| SV. 400 to 500 incl. |
0,5 | 0,64 | 0,8 | 1,0 | 1,20 | 1,6 | 2,0 | 2,40 | 3,2 | 4,0 | 5,0 |
| SV. 500 630 incl. |
0,64 | 0,8 | 1,0 | 1,20 | 1,6 | 2,0 | 2,40 | 3,2 | 4,0 | 5,0 | 6,4 |
| SV. 630 800 incl. |
0,8 | 1,0 | 1,20 | 1,6 | 2,0 | 2,40 | 3,2 | 4,0 | 5,0 | 6,4 | 8,0 |
| SV. 800 to 1000 incl. |
1,0 | 1,20 | 1,6 | 2,0 | 2,40 | 3,2 | 4,0 | 5,0 | 6,4 | 8,0 | 10,0 |
| SV. 1000 to 1200 incl. |
1,20 | 1,6 | 2,0 | 2,40 | 3,2 | 4,0 | 5,0 | 6,4 | 8,0 | 10,0 | 12,0 |
| SV. 1200 to 1600 incl. |
1,6 | 2,0 | 2,40 | 3,2 | 4,0 | 5,0 | 6,4 | 8,0 | 10,0 | 12,0 | 16,0 |
| SV. 1600 2000 incl. |
2,0 | 2,40 | 3,2 | 4,0 | 5,0 | 6,4 | 8,0 | 10,0 | 12,0 | 16,0 | 20,0 |
| SV. 2000 to 2500 incl. |
2,40 | 3,2 | 4,0 | 5,0 | 6,4 | 8,0 | 10,0 | 12,0 | 16,0 | 20,0 | 24,0 |
| SV. 2500 to 3150 incl. |
3,2 | 4,0 | 5,0 | 6,4 | 8,0 | 10,0 | 12,0 | 16,0 | 20,0 | 24,0 | 32,0 |
| SV. 3150 to 4000 incl. |
4,0 | 5,0 | 6,4 | 8,0 | 10,0 | 12,0 | 16,0 | 20,0 | 24,0 | 32,0 | 40,0 |
| SV. 4,000 to 5,000 incl. |
5,0 | 6,4 | 8,0 | 10,0 | 12,0 | 16,0 | 20,0 | 24,0 | 32,0 | 40,0 | 50,0 |
| SV. 5000 to 6300 incl. |
6,4 | 8,0 | 10,0 | 12,0 | 16,0 | 20,0 | 24,0 | 32,0 | 40,0 | 50,0 | 64,0 |
| SV. 6300 to 8000 incl. |
8,0 | 10,0 | 12,0 | 16,0 | 20,0 | 24,0 | 32,0 | 40,0 | 50,0 | 64,0 | 80,0 |
| SV. 8000 to 10000 incl. |
10,0 | 12,0 | 16,0 | 20,0 | 24,0 | 32,0 | 40,0 | 50,0 | 64,0 | 80,0 | |
| SV. 10000 |
12,0 | 16,0 | 20,0 | 24,0 | 32,0 | 40,0 | 50,0 | 64,0 | 80,0 | ||
| Note — the nominal size regulated plot in determining tolerances, form should take the largest of the sizes specified portion of the casting member, which regulates the deviation of the shape of the surface. | |||||||||||
Table 2 (Modified edition, Rev. N 2).
Tolerances of form, are shown in table 2 do not take into account casting biases, appointed in accordance with GOST 3212.
Location tolerances include position tolerances and tolerances of the offset.
Position tolerance when machining holes or lugs are relatively flat bases 1 and 2 (figure 5A) should be defined as overall tolerance of nominal sizes from bases 1 and 2 to the axis of the hole
Formula (1) (Deleted, Rev. N 2).
a — axis of the holes relative to datum machining, b — axis diameter of the hole relative to the axis of the base diameter
;
— the size tolerance; 1, 2, 3 — base;
— the inner surface
Figure 5 — Position tolerance
Position tolerance when machining internal diameter relative to the external base diameter must correspond to half the tolerance of the base diameter 
(Changed edition, Rev. N 2).
5.6 Tolerances the roundness, coaxiality, symmetry, the intersection of the axes, positional tolerances in diametrical terms shall not exceed the tolerances established in table 1.
5.7 Tolerance offset from the plane of the connector is equal to the difference between the maximum deviations of the provisions of the parts of the casting formed in different proforma (figure 6).
,
— the maximum and minimum diameters of the casting due to displacement
— the offset tolerance; MF — plane of the connector
Figure 6 — the Offset in the plane of the connector casting
The offset tolerance of the casting at the plane of the connector in the expression set table 1 class-level of dimensional accuracy of the casting as the nominal size of the thinnest of the walls of the casting, facing the connector, or crossing it.
5.8 the Tolerance of the offset caused by the misalignment of the rod should be set in the expression in table 1 for 1, 2 of class or rather class of dimensional accuracy of the casting, the nominal size of the thinnest wall casting formed with participation of the rod.
5.9 General tolerances of the casting surface, take into account the combined effect of the dimension tolerance from the surface to the base, tolerances of form are processed and the underlying surfaces, and tolerances of location. When determining the overall tolerance of the element surface of the casting table I. 1 of the application And the components values of tolerances should be placed in order of their descending order according to figure 7. The tolerance values and
should be found in the first and second columns of table I. 1, in the third column find the intermediate results
.
Figure 7
5.10 Tolerances surface roughness of castings shall be as specified in table 3.
Table 3 — Tolerances for the surface roughness of castings
| Tolerance of irregularities in the casting, mm, not more, for degrees precision cast surface | |||||||||||||||||||||
| 1 |
2 | 3 | 4 | 5 | 6 | 7 | 8 | 9 | 10 | 11 | 12 | 13 | 14 | 15 | 16 | 17 | 18 | 19 | 20 | 21 | 22 |
| 0,05 |
0,06 | 0,08 | 0,1 | 0,12 | 0,16 | 0,2 | 0,24 | 0,32 | 0,4 | 0,5 | 0,64 | 0,8 | 1,0 | 1,2 | 1,6 | 2,0 | 2,4 | 3,2 | 4,0 | 5,0 | 6,4 |
(Changed edition, Rev. N 1, 2).
5.11 To machined surfaces of castings established a symmetric layout of the fields of the tolerances of the machined surfaces is allowed symmetric and asymmetric (partially or fully) the location of tolerance zones of size, shape and location.
Set the symmetrical position of tolerance zones of neravnomernosti surfaces of castings.
6 Tolerances mass of castings
6.1 the Tolerances on the mass of castings shall be as specified in table 4.
Table 4 — weight Tolerances of castings
| Nominal casting weight, kg | The tolerance of the casting mass, %, max, accuracy classes for mass casting | ||||||||||
| 1 | 2 | 3T | 3 | 4 | 5T | 5 | 6 | 7T | 7 | 8 | |
| To 0.1 incl. |
1,6 | 2,0 | 2,4 | 3,2 | 4,0 | 5,0 | 6,4 | 8,0 | 10,0 | 12,0 | 16,0 |
| SV. 0.1 to 0.4 incl. |
1,2 | 1,6 | 2,0 | 2,4 | 3,2 | 4,0 | 5,0 | 6,4 | 8,0 | 10,0 | 12,0 |
| SV. 0.4 to 1.0 incl. |
1,0 | 1,2 | 1,6 | 2,0 | 2,4 | 3,2 | 4,0 | 5,0 | 6,4 | 8,0 | 10,0 |
| SV. 1.0 to 4.0 incl. |
- | 1,0 | 1,2 | 1,6 | 2,0 | 2,4 | 3,2 | 4,0 | 5,0 | 6,4 | 8,0 |
| SV. 4,0 to 10,0 incl. |
- | - | 1,0 | 1,2 | 1,6 | 2,0 | 2,4 | 3,2 | 4,0 | 5,0 | 6,4 |
| SV. 10.0 to 40.0 incl. |
- | - | - | 1,0 | 1,2 | 1,6 | 2,0 | 2,4 | 3,2 | 4,0 | 5,0 |
| SV. Of 40.0 to 100.0 incl. |
- | - | - | - | 1,0 | 1,2 | 1,6 | 2,0 | 2,4 | 3,2 | 4,0 |
| SV. Up to 400,0 100,0 incl. |
- | - | - | - | - | 1,0 | 1,2 | 1,6 | 2,0 | 2,4 | 3,2 |
| SV. To 1000,0 400,0 incl. |
- | - | - | - | - | - | 1,0 | 1,2 | 1,6 | 2,0 | 2,4 |
| SV. To 1000,0 4000,0 incl. |
- | - | - | - | - | - | - | 1,0 | 1,2 | 1,6 | 2,0 |
| SV. 4000,0 up to 10000,0 incl. |
- | - | - | - | - | - | - | - | 1,0 | 1,2 | 1,6 |
| SV. 10000,0 to 40000,0 incl. |
- | - | - | - | - | - | - | - | - | 1,0 | 1,2 |
| SV. 40000,0 to 100000,0 incl. |
- | - | - | - | - | - | - | - | - | - | 1,0 |
| SV. 100000,0 |
- | - | - | - | - | - | - | - | - | - | - |
Continuation of table 4
| Nominal casting weight, kg | The tolerance of the casting mass, %, max, accuracy classes for mass casting | ||||||||||
| 9T | 9 | 10 | 11T | 11 | 12 | 13t | 13 | 14 | 15 | 16 | |
| To 0.1 incl. |
20,0 | 24,0 | 32,0 | - | - | - | - | - | - | - | - |
| SV. 0.1 to 0.4 incl. |
16,0 | 20,0 | 24,0 | 32,0 | - | - | - | - | - | - | - |
| SV. 0.4 to 1.0 incl. |
12,0 | 16,0 | 20,0 | 24,0 | 32,0 | - | - | - | - | - | - |
| SV. 1.0 to 4.0 incl. |
10,0 | 12,0 | 16,0 | 20,0 | 24,0 | 32,0 | - | - | - | - | - |
| SV. 4,0 to 10,0 incl. |
8,0 | 10,0 | 12,0 | 16,0 | 20,0 | 24,0 | 32,0 | - | - | - | - |
| SV. 10.0 to 40.0 incl. |
6,4 | 8,0 | 10,0 | 12,0 | 16,0 | 20,0 | 24,0 | 32,0 | - | - | - |
| SV. Of 40.0 to 100.0 incl. |
5,0 | 6,4 | 8,0 | 10,0 | 12,0 | 16,0 | 20,0 | 24,0 | 32,0 | - | - |
| SV. Up to 400,0 100,0 incl. |
4,0 | 5,0 | 6,4 | 8,0 | 10,0 | 12,0 | 16,0 | 20,0 | 24,0 | 32,0 | - |
| SV. To 1000,0 400,0 incl. |
3,2 | 4,0 | 5,0 | 6,4 | 8,0 | 10,0 | 12,0 | 16,0 | 20,0 | 24,0 | 32,0 |
| SV. To 1000,0 4000,0 incl. |
2,4 | 3,2 | 4,0 | 5,0 | 6,4 | 8,0 | 10,0 | 12,0 | 16,0 | 20,0 | 24,0 |
| SV. 4000,0 up to 10000,0 incl. |
2,0 | 2,4 | 3,2 | 4,0 | 5,0 | 6,4 | 8,0 | 10,0 | 12,0 | 16,0 | 20,0 |
| SV. 10000,0 to 40000,0 incl. |
1,6 | 2,0 | 2,4 | 3,2 | 4,0 | 5,0 | 6,4 | 8,0 | 10,0 | 12,0 | 16,0 |
| SV. 40000,0 to 100000,0 incl. |
1,2 | 1,6 | 2,0 | 2,4 | 3,2 | 4,0 | 5,0 | 6,4 | 8,0 | 10,0 | 12,0 |
| SV. 100000,0 |
1,0 | 1,2 | 1,6 | 2,0 | 2,4 | 3,2 | 4,0 | 5,0 | 6,4 | 8,0 | 10,0 |
| Note — the Tolerances on the weight of the castings is given in percent of the nominal weight of casting. | |||||||||||
6.2 Set the symmetrical position of the tolerance field of the mass relative to the nominal mass.
