Alloy ML11
Alloy ML23
Alloy ML9
Alloy ML8
Alloy ML7-1
Alloy ML6
Alloy ML5pch
Alloy ML5on
Alloy ML5-2
Alloy ML5-1
Alloy ML5
Alloy ML4pch
Alloy ML4
Alloy ML3
Alloy ML22
Alloy ML21
Alloy ML20-1
Alloy ML2
Alloy ML19 (VML7)
Alloy ML18 (VML6)
Alloy ML17 (VML5)
Alloy ML15
Alloy ML12
Alloy ML11
Alloy ML10
Designation
| Name | The value |
|---|---|
| Designation GOST Cyrillic | МЛ11 |
| Designation GOST Latin | ML11 |
| Transliteration | ML11 |
| The chemical elements | CuЛ11 |
Description
ML11 alloy used: for the manufacture of castings parts that require high containment and experiencing high loads with maximum working temperature of +250 °C — long, +300 °C short — term.
Note
High-temperature alloy system MD-REE-Zr. For alloying of the alloy of the rare earth metals cerium mischmetal used (75% Se and 25% other REE cerium group). The alloy contains also supplements of zinc and zirconium.
ML11 alloy doped by zeraphim a Misch metal, has lower mechanical properties at room temperature. Its technological and casting properties are close alloys with neodymium, the castings have high integrity.
Standards
| Name | Code | Standards |
|---|---|---|
| Non-ferrous metals, including rare metals, and their alloys | В51 | GOST 2856-79 |
| Castings from non-ferrous metals and alloys | В84 | OST 1 90248-77 |
Chemical composition
| Standard | Si | Ni | Fe | Cu | Al | Zn | Zr | Mg | Be |
|---|---|---|---|---|---|---|---|---|---|
| GOST 2856-79 | ≤0.03 | ≤0.005 | ≤0.02 | ≤0.03 | ≤0.02 | 0.2-0.7 | 0.4-1 | The rest | ≤0.001 |
Mg is the basis.
According to GOST 2856-79 the sum of REM should be within the range of 2.50-4.00%. The content of other impurities is ≤ 0.12%, the sum of detectable impurities is 0.20%.
According to GOST 2856-79 the sum of REM should be within the range of 2.50-4.00%. The content of other impurities is ≤ 0.12%, the sum of detectable impurities is 0.20%.
Mechanical characteristics
| Section, mm | sT|s0,2, MPa | σB, MPa | d5, % |
|---|---|---|---|
| Casting in sand, shell, investment casting and plaster mold and chill casting GOST 2856-79. Without heat treatment | |||
| ≥70 | ≥120 | ≥1.5 | |
| Casting in sand, shell, investment casting and plaster mold and chill casting GOST 2856-79. Mode T2: Annealing | |||
| ≥70 | ≥120 | ≥1.5 | |
| Casting in sand, shell, investment casting and plaster mold and chill casting GOST 2856-79. Mode T4: Homogenization + annealing in air | |||
| ≥85 | ≥140 | ≥3 | |
| Casting in sand, shell, investment casting and plaster mold and chill casting GOST 2856-79. T6 mode: Homogenization + annealing at air + aging | |||
| ≥100 | ≥140 | ≥2 | |
Description mechanical marks
| Name | Description |
|---|---|
| Section | Section |
| sT|s0,2 | Yield strength or limit of proportionality with a tolerance for residual deformation of 0.2% |
| σB | Limit short-term strength |
| d5 | Elongation after rupture |
