By visiting this site, you accept the use of cookies. More about our cookie policy.

Bronze Bro10s10 (БрОС10-10)

Bronze БрО3Ц8С4Н1 (БрОЦСН3-8-4-1) Bronze БрО8Ц4 (БрОЦ8-4) Bronze БрО8С21 (БрОС8-21) Bronze БрО8С12 (БрОС8-12) Bronze БрО8Н4Ц2 (БрОНЦ8,5-4-2) Bronze БрО6Ц6С3 (БрОЦС6-6-3) Bronze БрО6Ц6С2х (БрОЦС6-6-2х) Bronze БрО6Ц4С2Н1 (БрОЦСН6-4-2-1) Bronze БрО6С6Ц3 Bronze БрО6К2Ц1 Bronze БрО5Ц6С5 (БрОЦС5-6-5) Bronze БрО5Ц5С5 (БрОЦС5-5-5) Bronze БрО5С25 (БрОС5-25) Bronze БрО4Ц8С5 Bronze БрО4Ц7С5 (БрОЦС3,5-7-5) Bronze БрО4Ц4С17 (БрОЦС4-4-17) Bronze БрО3Ц7С5Н1 (БрОЦСН3-7-5-1) Bronze БрО3Ц6С5 (БрОЦС3-6-5) Bronze БрО3Ц13С4 (БрОЦС3-13-4) Bronze БрО3Ц12С5 (БрОЦС3-12-5) Bronze БрО3,5Ц7С5 Bronze BrO19 Bronze БрО16С5 (БрОС16-5) Bronze БрО10Ц2Н2 (БрОЦН10-2-2) Bronze БрО10Ц2Н1,5 (БрОЦН10-2-1,5) Bronze БрО10Ц2 (БрОЦ10-2) Bronze БрО10Ф1 (БрОФ10-1) Bronze БрО10Ф0,7Н0,5 (БрОФН10-0,7-0,5) Bronze БрО10С2Н3 (БрОСН10-2-3) Bronze БрО10С10 (БрОС10-10)

Designation

Name The value
Designation GOST Cyrillic БрО10С10
Designation GOST Latin BpO10C10
Transliteration BrO10S10
The chemical elements BaSn10Pb10
Name The value
Designation GOST Cyrillic БрОС10-10
Designation GOST Latin BpOC10-10
Transliteration BrOS10-10
The chemical elements BaSnPb10-10

Description

Bronze Bro10s10 used: for the manufacture of plain bearings operating under conditions of high specific pressure; castings.

Standards

Name Code Standards
Non-ferrous metals, including rare metals, and their alloys В51 GOST 613-79, OST 1 90054-72
Castings from non-ferrous metals and alloys В84 OST 1 90046-72

Chemical composition

Standard S P Si Ni Fe Cu As Al Zn Sn Sb Pb Bi Mg
GOST 613-79 ≤0.05 ≤0.05 ≤0.02 ≤2 ≤0.2 The rest ≤0.15 ≤0.02 ≤0.5 9-11 ≤0.3 8-11 - ≤0.02
OST 1 90054-72 - ≤0.3 ≤0.02 - ≤0.25 The rest - ≤0.02 ≤0.2 8-10 ≤0.3 6-11 ≤0.02 -
Cu is the basis.
The total fraction of impurities in the OST 1 90054-72 (elements with a content ≤) is 0.8%. Impurities that are not regulated by the table are included in the total amount of impurities.
According to GOST 613-79, the total content of impurities should be ≤ 0.90%. Impurities not regulated by the standard are included in the total amount of impurities. The mass fraction of nickel due to copper and the amount of impurities is not included. The mass fraction of phosphorus, as agreed by the manufacturer with the consumer, is allowed up to 1.00%, and in this case the total amount of impurities is not included.

Mechanical characteristics

σB, MPa d5, % Brinell hardness number, MPa
Castings are supplied without heat treatment
≥176.2 ≥7 ≥65
≥196 ≥6 ≥78
Casting investment casting according to OST 1 90046-72 (samples separately cast or cut from castings)
≥196 ≥10 ≥55

Description mechanical marks

Name Description
σB Limit short-term strength
d5 Elongation after rupture

Our consultant will save your time

+49(1523) 72 15 100
E-mail:
Telegram:
WhatsApp:
Ask a question

Subscription

Special offers and discounts. :)
brass Circle, 29nk circle, Tape XH78T, 15h25t sheet, Inconel alloy