By visiting this site, you accept the use of cookies. More about our cookie policy.

Aluminium AD1 (1013)

Aluminum 1050 Aluminum 1145 Aluminum AD (1015) Aluminum AD0 (1011) Aluminum AD00 (1010) Aluminum AD000 Aluminum AD1 (1013) ADS Aluminum

Designation

Name The value
Designation GOST Cyrillic АД1
Designation GOST Latin AD1
Transliteration AD1
The chemical elements -
Name The value
Designation GOST Cyrillic 1013
Designation GOST Latin 1013
Transliteration 1013
The chemical elements 1013

Description

Aluminium AD1 is used: for the manufacture of flat ingots, cast by semi-continuous method or continuous casting, and is intended for rolling into sheets, strips and other semi-finished products (strips, plates, profiles, panels, rods, tubes, drawn wire, stampings and forgings) by hot or cold deformation, as well as ingots and slabs; sheets used in the printing industry; profiles pressed extra virgin for the manufacture of radiators of cooling of semiconductor devices; foil used to manufacture capacitors; pressed large pipes; special profiles by cold extrusion; cold-formed profiles for the cladding of building structures; extruded pipes with controlled inner diameter from 14 to 42 mm for heat exchangers; heat exchangers evaporators and condensers with two-sided bulge of the channel used in domestic refrigerators and freezers; roll foil used for thermal, hydro and sound insulation; cold-rolled foil intended for packaging of food, drugs, medical devices, cosmetic products industry, as well as for the production of packaging materials based on it; bimetallic sheets with the steel grade 08CR18NI10TI; tape in rolls clad with copper on one side (APM-1) and intended for various products in the electrical industry; round wire for cold upsetting.

Note

ISO 209−1 aluminum brand AD1 is designated А199,3.

Standards

Name Code Standards
Tapes В54 GOST 1018-77, GOST 13726-97, TU 1-2-404-80, TU 1-2-421-81, TU 1-2-432-82, TU 1-2-433-82, TU 1-2-434-82
Wire of non-ferrous metals and their alloys В74 GOST 14838-78, OST 1 92005-2002, OST 4.021.101-92
Pipes from non-ferrous metals and alloys В64 GOST 18475-82, GOST 18482-79, OST 1 92048-90, OST 1 92048-76, OST 4.021.119-92, OST 1 92047-76, TU 1-1-198-89, TU 1-3-118-91, TU 1-3-120-92, TU 1-3-138-91, TU 1-3-67-90, TU 1-3-26-93, TU 1-3-019-93, TU 1-3-67-98
Bars В55 GOST 21488-97, OST 4.021.017-92
Non-ferrous metals, including rare metals, and their alloys В51 GOST 4784-97, GOST 9498-79, GOST 19437-81, OST 1 92014-90, OST 4.021.009-92
Sheets and stripes В53 GOST 618-73, GOST 10703-73, GOST 17232-99, GOST 21631-76, GOST 25001-81, GOST 25905-83, GOST 745-2003, OST 4-021.048-78, OST 4.021.092-92, TU 1-9-1048-87, TU 1-9-413-84, TU 1-9-4-85, TU 1-9-637-74, TU 1-9-688-82, TU 1-9-548-87
Sectional and shaped rolling В52 GOST 8617-81, GOST 13616-97, GOST 13617-97, GOST 13618-97, GOST 13619-97, GOST 13620-90, GOST 13621-90, GOST 13622-91, GOST 13623-90, GOST 13624-90, GOST 13737-90, GOST 13738-91, GOST 17575-90, GOST 17576-97, GOST 18591-91, GOST 24767-81, GOST 29296-92, GOST 29303-92, GOST Р 50066-92, GOST Р 50067-92, GOST Р 50077-92, OST 1 92093-83, OST 1 92069-77, TU 1-9-631-73
Metal forming. Forgings В03 OST 26-01-152-82

Chemical composition

Standard Mn Si Fe Cu Al Ti Zn Mg
GOST 4784-97 ≤0.025 ≤0.3 ≤0.3 ≤0.05 ≥99.3 ≤0.15 ≤0.1 ≤0.05
Al is the base.
According to GOST 4784-97, the mass fraction of other impurities is ≤ 0.05% of each, the total mass fraction of all impurities is ≤ 0.70%. For aluminum AD1pl, the mass percentages of impurities are set: silicon ≤ 0.30%, copper ≤ 0.020%, manganese ≤ 0.025%, magnesium ≤ 0.050%, iron ≤ 0.30%, zinc ≤ 0.10%, titanium ≤ 0.150, (not regulated) impurities of each ≤ 0.010%.

Mechanical characteristics

Section, mm sT|s0,2, MPa σB, MPa d5, % d d10
The tape is supplied according to GOST 1018-77 (samples)
0.3-0.7 - ≥70 - ≥20 -
0.3 - 100-150 - ≥2.5 -
0.35-0.7 - 120-150 - ≥3 -
Full hard sheet for the printing industry (0,35-0,80 mm) as supplied
- 135-195 - - ≥4
Sheet metal in delivery condition according to GOST 21631-76, OST 4.021.047-92 tape according to GOST 13726-97 (samples transverse)
5-10.5 - ≥70 - ≥15 -
0.3-0.5 - ≥60 - ≥20 -
0.5-0.9 - ≥60 - ≥25 -
0.9-10.5 - ≥60 - ≥30 -
0.3-0.8 - ≥145 - ≥3 -
0.8-3.5 - ≥145 - ≥4 -
3.5-10.5 - ≥130 - ≥5 -
0.8-4.5 - ≥100 - ≥6 -
Plates according to GOST 17232-99. 4.021.061-92 supplied without heat treatment (samples transverse)
11-25 - ≥78 ≥18 - -
25-80 - ≥64 ≥15 - -
Forging after annealing at OST 26-01-152-82
≥30 ≥60 ≥25 - -
The wire drawn according to OST 1 92005-2002
3.9-12 - - - ≥20 -
Extruded normal strength according to GOST 8617-81 on delivery
- ≥59 ≥20 - -
The special extruded profile with subsequent drawing GOST 18591-91 (as supplied)
- ≥98 - - -
Round bars normal strength in the delivery condition in the OST 4.021.017-92 (longitudinal samples)
8-250 - ≥60 ≥25 - -
The pressed bars normal strength in the delivery condition according to GOST 21488-97 (longitudinal samples)
8-300 - ≥60 ≥25 - -
Extruded aluminum tubes with internal diameter control for heat exchangers as supplied without a heat treatment on the other 1-3-67-90 (in the section you specify an internal pipe diameter)
14-42 - 59-98 - ≥28 -
Tubes extruded in the state of delivery according to GOST 18482-79 (samples, in cross-section shows the thickness of the wall)
- ≥60 ≥20 - -
Large-size extruded tubes according to OST 1 92048-76 on delivery
- ≥59 ≥20 - -
Cold-rolled tubes in the delivery condition according to GOST 18475-82, OST 4.021.119-92 samples (in cross-section shows the thickness of the wall)
- 60-110 - - ≥20
≤2 - ≥110 - - ≥4
2-5 - ≥100 - - ≥5
Foil as supplied by OST 4.021.092-92 (samples)
0.007-0.011 - ≥30 - - -
0.011-0.045 - ≥35 - ≥2 -
0.045-0.2 - ≥40 - ≥3 -
0.007-0.045 - ≥100 - - -
0.045-0.2 - ≥120 - - -

Description mechanical marks

Name Description
Section Section
sT|s0,2 Yield strength or limit of proportionality with a tolerance for residual deformation of 0.2%
σB Limit short-term strength
d5 Elongation after rupture
d Elongation after rupture
d10 Elongation after rupture

Physical characteristics

Temperature Е, ГПа r, кг/м3 l, Вт/(м · °С) R, НОм · м a, 10-6 1/°С
20 71 2710 - 292 -
100 - - 226 - 24
200 - - - - 256

A description of the physical symbols

Name Description
Е The normal elasticity modulus
r Density
l Coefficient of thermal conductivity
R UD. the resistivity
С Specific heat

Our consultant will save your time

+49 (170) 650 7006
E-mail:
Telegram:
WhatsApp:
Ask a question

Subscription

Special offers and discounts. :)
14h17n2 sheet, XH78T pipe, Trumpet brass, Titanium wire, Sheet aisi 321