Aluminium A6
	
	
Designation
	
		
			| Name | 
			The value | 
		
	
	
		
			| Designation GOST Cyrillic | 
			А6 | 
		
		
			| Designation GOST Latin | 
			A6 | 
		
		
			| Transliteration | 
			A6 | 
		
		
			| The chemical elements | 
			- | 
		
	
	Description
	Aluminium A6 is used: for the production of pigs, ingots, wire rod, flat ingots, cast by semi-continuous method or continuous casting, and is intended for rolling into sheets, strips and other semi-finished products; extruded pipes with controlled inner diameter from 14 to 42 mm for heat exchangers; heat exchangers evaporators and condensers with two-sided bulge of the channel used in domestic refrigerators and freezers; foil used to manufacture capacitors; roll foil used for thermal, hydro and sound insulation; cold-rolled foil intended for packaging food, medicines, medical products, products of the cosmetic industry and for the production of packaging materials based on it; blue foil of 0.05−0.20 mm for electrical equipment of the aircraft industry; aluminum powder brands commandos APS-1A and APS-1B, APS-2, APS-3 is intended for the production teploperenosa deformable material type SAP.
Note
Aluminium technical purity.
Aluminum grade A6 corresponds to the chemical composition of the marches of aluminium EN AW-1060, installed in the European standard EN 1060 and 573−3-94 Marche, was the American aluminum Association.
Standards
	
		
			| Name | 
			Code | 
			Standards | 
		
	
	
		
	| Solid alloys, metal-ceramic products and powders, metal | 
	В56 | 
	GOST 10096-76 | 
	| Tapes | 
	В54 | 
	GOST 1018-77, GOST 13726-97, TU 1-1-98-88, TU 1-2-133-77, TU 1-2-426-87, TU 1-2-432-82 | 
	| Pipes from non-ferrous metals and alloys | 
	В64 | 
	GOST 18482-79, TU 1-3-67-90, TU 1-3-67-98 | 
	| Sheets and stripes | 
	В53 | 
	GOST 618-73, GOST 17232-99, GOST 21631-76, GOST 25001-81, GOST 25905-83, GOST 745-2003, OST 4.021.093-92, TU 1-9-1048-87, TU 1-8-186-2006 | 
	| Sectional and shaped rolling | 
	В52 | 
	GOST 8617-81, GOST 13616-97, GOST 13617-97, GOST 13618-97, GOST 13619-97, GOST 13620-90, GOST 13621-90, GOST 13622-91, GOST 13623-90, GOST 13624-90, GOST 13737-90, GOST 13738-91, GOST 17575-90, GOST 17576-97, GOST 29296-92, GOST 29303-92, GOST Р 50066-92, GOST Р 50067-92, GOST Р 50077-92 | 
	| Non-ferrous metals, including rare metals, and their alloys | 
	В51 | 
	GOST 9498-79, GOST 11069-2001, GOST 11070-74, GOST 19437-81, OST 4.021.009-92 | 
	
Chemical composition
	
		
			| Standard | 
			
Mn | 
 
Si | 
 
Fe | 
 
Cu | 
 
Al | 
 
Ti | 
 
Zn | 
 
Mg | 
		
	
	
		
	| GOST 11069-2001 | 
	
≤0.03 | 
≤0.18 | 
≤0.25 | 
≤0.01 | 
≥99.6 | 
≤0.02 | 
≤0.05 | 
≤0.03 | 
	
Al is the base. 
 According to GOST 19437-81 and GOST 11069-2001, the Ga content is ≤ 0.030%. The content of other impurities (each separately) ≤ 0.030%. The total content of all impurities is ≤ 0.40%.
Mechanical characteristics
	
		
			
| Section, mm | 
 
σB, MPa | 
 
d5, % | 
 
d | 
		
	
	
		
	| The tape is supplied according to GOST 1018-77 (samples) | 
	
| 0.3-0.7 | 
≥70 | 
- | 
≥20 | 
	
| 0.3 | 
100-150 | 
- | 
≥2.5 | 
	
| 0.35-0.7 | 
120-150 | 
- | 
≥3 | 
	| Sheet metal in delivery condition according to GOST 21631-76, OST 4.021.047-92 tape according to GOST 13726-97 (samples transverse) | 
	
| 5-10.5 | 
≥70 | 
- | 
≥15 | 
	
| 0.3-0.5 | 
≥60 | 
- | 
≥20 | 
	
| 0.5-0.9 | 
≥60 | 
- | 
≥25 | 
	
| 0.9-10.5 | 
≥60 | 
- | 
≥30 | 
	
| 0.3-0.8 | 
≥145 | 
- | 
≥3 | 
	
| 0.8-3.5 | 
≥145 | 
- | 
≥4 | 
	
| 3.5-10.5 | 
≥130 | 
- | 
≥5 | 
	
| 0.8-4.5 | 
≥100 | 
- | 
≥6 | 
	| Plates according to GOST 17232-99. 4.021.061-92 supplied without heat treatment (samples transverse) | 
	
| 11-25 | 
≥78 | 
≥18 | 
- | 
	
| 25-80 | 
≥64 | 
≥15 | 
- | 
	| Extruded aluminum tubes with internal diameter control for heat exchangers as supplied without a heat treatment on the other 1-3-67-90 (in the section you specify an internal pipe diameter) | 
	
| 14-42 | 
59-98 | 
- | 
≥28 | 
	| Tubes extruded in the state of delivery according to GOST 18482-79 (samples, in cross-section shows the thickness of the wall) | 
	
 | 
≥60 | 
≥20 | 
- | 
	
Description mechanical marks
	
		
			| Name | 
			Description | 
		
	
	
		
	| Section | 
	Section | 
	| σB | 
	Limit short-term strength | 
	| d5 | 
	Elongation after rupture | 
	| d | 
	Elongation after rupture | 
	
Physical characteristics
	
		
			| Temperature | 
			
r, кг/м3 | 
		
	
	
		
	| 20 | 
	
2700 | 
	
A description of the physical symbols
	
		
			| Name | 
			Description | 
		
	
	
		
	| Е | 
	The normal elasticity modulus | 
	| l | 
	Coefficient of thermal conductivity | 
	| R | 
	UD. the resistivity | 
	| С | 
	Specific heat |