GOST R 53364-2009

• gost-r-53364-2009.pdf (241.44 KiB)
  ГОСТ Р 53364-2009

GOST R 53364−2009 (ISO 10474:1991) steel Pipes and products from pipes. Documents on acceptance inspection

GOST R 53364−2009
(ISO 10474:1991)

Group В62

NATIONAL STANDARD OF THE RUSSIAN FEDERATION

STEEL PIPES AND PRODUCTS FROM PIPES

Documents on acceptance inspection

Steel pipes, tubes and pipe products. Inspection documents

OKS 77.140.01
OKP 13 0000

Date of introduction 2010−03−01

Preface

The objectives and principles of standardization in the Russian Federation established by the Federal law of 27 December 2002 N 184-FZ «On technical regulation», and rules for the application of national standards of the Russian Federation — GOST R 1.0−2004"Standardization in the Russian Federation. The main provisions"

Data on standard

1 PREPARED by the Technical Committee for standardization TC 357 «Steel and cast iron pipes and cylinders», Open joint stock company «Russian scientific research Institute of pipe industry» (JSC «RosNITI») based on the authentic translation of the standard referred to in paragraph 4, which is made by the Russian research Institute of standardization (Vniistandart)

2 SUBMITTED by the Technical Committee for standardization TC 357 «Steel and cast iron pipes and cylinders"

3 APPROVED AND put INTO EFFECT by the Federal Agency for technical regulation and Metrology dated July 16, 2009 N 250-St

4 this standard is modified in relation to the international standard ISO 10474:1991, «Steel and steel products. Documents on acceptance inspection» (ISO 10474:1991 «Steel and steel products — Inspection documents»). This standard modified the scope of this standard applies only to documents on the acceptance inspection for the supply of steel pipes and products from pipes. Thus in this standard are not included normative references applied international standard because they do not apply to steel pipe and products pipe. Section «Terms and definitions» is supplemented by terms.

All changes made to the text of this standard in comparison with the international standard in italics

5 INTRODUCED FOR THE FIRST TIME


Information about the changes to this standard is published in the annually issued reference index «National standards», and the text changes and amendments — in monthly indexes published information «National standards». In case of revision (replacement) or cancellation of this standard a notification will be published in a monthly information index «National standards». Relevant information, notification and lyrics are also posted in the information system of General use — on the official website of the Federal Agency for technical regulation and Metrology on the Internet

1 General provisions*

_________________
* The name of the item 1 in the original paper are shown in italics. — Note the manufacturer’s database.

1.1 Scope of

________________
* The word «use» in the name of article 1.1 in the original paper are shown in italics. — Note the manufacturer’s database.

This standard applies to various documents on acceptance inspectionfor the supply of steel pipes for different purposes and products from pipesthat are provided to the customer in accordance with the requirement of the order.

A real standard part of the delivery conditions shall be applied together with other standards for steel tube and pipe products.

1.2 Terms and definitions

________________
* The word «Terms» in the name of the item 1.2 in the original paper are shown in italics. — Note the manufacturer’s database.

In the present standard applies the following terms with respectivedefinitions:

1.2.1 conventional control and testing: Monitoring and testing conducted by the manufacturer in accordance with the production process to ensure conformity of the product within the technological process, the requirements of the order.

Products, which are subject to the control and testing need not be of the party intended for delivery.

Note — currently there are discussions about the replacement of the term «inspection and test» on «control».

1.2.2 special monitoring and testing: Monitoring and testing carried out before delivery in accordance with the technical requirements of the order on the samples or products from the batchintended for delivery, to verify conformity of products to requirements of the order.

1.2.3 the authorised representative of the manufacturer who may be busy in the production process: the Specialist directly involved in the organization and management of the production process.

1.2.4 authorized representative of manufacturer not engaged in the production process: a Specialist who is not participating in the organization and management of production.

1.2.5 the inspector specified in official regulatory documents Specialist, responsible for supervising the persons carrying out technical checks and signing documents on the results of the tests.

1.2.6 specification of the order: the List of specifications, which must match the ordered product.

2 Documents drawn up on the basis of inspection and testing performed by an authorized representative of manufacturer who may be busy in the production process

2.1 certificate of compliance with the order

________________
* The word «Witness» in the name of the item 2.1 in the original paper are shown in italics. — Note the manufacturer’s database.

The document in which the manufacturer certifies that the supplied products meet the requirements of the order, with test results in the document are not given.

Evidence of compliance with the order is a document drawn up on the basis of regular monitoring and testing.

2.2 test Protocol

The document in which the manufacturer certifies that the supplied productsmeet the requirements of the order, at the same time shows the test results based on regular monitoring and testing.

2.3 specific test Protocol

The document in which the manufacturer certifies that the supplied products meet the requirements of the order, and which presents test results based on the special control.

Special test use only manufacturers that do not have aservice of technical control, independent of production process.

If the manufacturer uses the services of independent technical control, it must submit an attestation of technical control «3.1» (3.1) isa special test Protocol.

3 Documents drawn up on the basis of specific inspection and testing carried out directly or under the control of authorized representative of manufacturer not engaged in the production process

________________
* The words «representative of manufacturer not engaged» in the name of the item 3 in the original paper are shown in italics. — Note the manufacturer’s database.

3.1 Certificate of technical control

The document issued on the basis of specific inspection and testing carried out in accordance with the requirements of the order.

Testing should be carried out to supply products or samplesthat are part of the product.

The number of samples set in the standards for technical delivery conditions for steel pipes and products from pipes or in the order.

There are three different types of certificates on passing technical inspection:

— certificate of technical control «3.1 A»; is issued and approved by theinspectorspecified in official regulatory documents;

— certificate of technical control «3.1»; shall be issued by the service are not involved in the production process, and approved by an authorized representative of manufacturer not engaged in a manufacturing process;

— certificate of technical control «3.1 C»; shall be issued and approved by the authorized representative of the user in accordance with the specification of the order.

3.2 acceptance

In the case where the result of a special agreement, the certificate of technical control at the same time approved by the authorized representatives of the manufacturer and consumer, such a document is called the certificate of acceptance.

4 the Documents that must be submitted by the manufacturer or intermediary

The manufacturer or middleman who supply the product, must provideto the consumer all documentation required by this standard without any modifications. This documentation should include the relevant methods of identification products to ensure the conformity of the relevant product documentation.

If the manufacturer or intermediary changes were made that impact on the qualityor the size of the product, they must present an additional document agreeing with the customer. This should also include any special requirements included in the production documentation.

5 validation of the documents on acceptance inspection

________________
* The words «acceptance inspection» in the name of the item 5 in the original paper are shown in italics. — Note the manufacturer’s database.

Documents on acceptance inspection must be signed or registeredby the authorized person (s) responsible (s) for checking the correctness of documents.

However, if the documents are prepared with the help of the automated data processing system, the signature may be replaced by specifying the names and titlesof the authorized person.

6 List of documents on acceptance inspection

________________
* The words «acceptance inspection» in the name of the item 6 in the original paper are shown in italics. — Note the manufacturer’s database.

The list of documents on acceptance inspection, set a real standard, are given in table 1.


Table 1 — List of documents on acceptance inspection