By visiting this site, you accept the use of cookies. More about our cookie policy.

Steel St6sp (ВСт6сп)

Designation

Name The value
Designation GOST Cyrillic Ст6сп
Designation GOST Latin Ct6cp
Transliteration St6sp
The chemical elements 6
Name The value
Designation GOST Cyrillic ВСт6сп
Designation GOST Latin BCt6cp
Transliteration VSt6sp
The chemical elements 6

Description

St6sp steel is used: for the manufacture of Bab hammers, spindles, wedges, construction scrap and other parts exposed to impact loads; parts of high strength (axles, shafts, fingers, pistons and other parts in heat treated condition); rod of rebar periodic profile, a trapezoidal profile for a bit and strip profile with thickening of agricultural machinery; two-headed rails, t-type P5, is designed for ground and suspended tracks.

Note

The degree of deoxidation — SP.

Standards

Name Code Standards
Pipes steel and connecting parts to them В62 GOST 3262-75, GOST 8732-78, GOST 9567-75, GOST 8731-87, GOST Р 53383-2009, TU 14-3-1160-83, TU 14-3-1428-86, TU 14-3-1473-87, TU 14-3Р-50-2001, TU 14-3-1654-89
Tapes В24 GOST 3560-73, STP М309-74
Classification, nomenclature and general norms В20 GOST 380-2005
Sectional and shaped rolling В22 GOST 5422-73, GOST 5781-82, GOST 8239-89, GOST 8240-97, GOST 8509-93, GOST 8510-86, GOST 12492.3-90, GOST 12492.8-90, GOST 12492.10-90, GOST 19240-73, GOST 19425-74, GOST 535-2005, GOST 2590-2006, GOST 2591-2006, GOST 2879-2006, OST 5.9086-85, OST 5.9087-84
Sheets and stripes В23 GOST 82-70, GOST 14918-80, GOST 19903-74, GOST 103-2006, GOST 19903-90
Bulls. Blanks. Slabs В31 OST 3-1686-90, TU 14-1-4944-90
Sheets and stripes В33 TU 14-1-4431-88
Sectional and shaped rolling В32 TU 14-2-849-89, TU 14-11-245-88, TU 14-1-1271-75, TU 14-136-367-2008

Mechanical characteristics

Section, mm sT|s0,2, MPa σB, MPa d5, % y, % kJ/m2, кДж/м2
Long products
- ≥325 ≥535 ≥25 ≥52 -
- ≥305 ≥505 ≥20 ≥53 -
- ≥305 - - ≥39 -
- ≥200 - ≥21 ≥51 -
- ≥180 ≥500 ≥23 ≥64 -
- ≥150 ≥355 ≥24 ≥70 -
- ≥81 ≥190 ≥35 ≥83 -
Rolled steel in the delivery state
≤25 ≥325 ≥535 ≥25 ≥52 ≥630
The hot rolled shapes in the state of delivery
20-40 ≥305 ≥590 ≥14 - -
20 ≥315 ≥590 ≥15 - -
40 ≥295 ≥590 ≥12 - -
Seamless hot deformed tubes in the delivery condition
≥305 ≥590 ≥14 - -
Normalization at 840-880 °C, air cooling to 450-500 °C + High tempering at 620-650 °C
300 - ≥640 ≥23 ≥42 -
Forgings. Quenching in water from 840-860 °C + Vacation at 600-640 °C
220 390-530 670-810 18-23 50-57 390-640
Forgings. Quenching in oil 840-860 °C + Vacation at 580-620 °C
220 390-530 700-850 17-24 46-54 340-540
Forgings. Isothermal annealing at 830-860 °C + Isothermal holding at 630-660 °C
400 - ≥640 ≥22 ≥42 -
Forgings. Annealing at 830-860 °C
400 - ≥670 ≥19 ≥36 -
A sample with a diameter of 10 and a length of 100 mm laminated. The rate of deformation of 120 mm/min and strain Rate of 0.02 1/s
- - ≥165 ≥33 ≥94 -
- - ≥105 ≥62 ≥95 -
- - ≥75 ≥50 ≥93 -
A sample with a diameter of 10 and a length of 50 mm laminated. The strain rate of 120 mm/min strain Rate of 0.04 1/s
- - ≥55 ≥92 ≥100 -
- - ≥37 ≥100 ≥100 -
- - ≥27 ≥106 ≥100 -

Description mechanical marks

Name Description
Section Section
sT|s0,2 Yield strength or limit of proportionality with a tolerance for residual deformation of 0.2%
σB Limit short-term strength
d5 Elongation after rupture
y The relative narrowing
kJ/m2 Toughness

Physical characteristics

Temperature Е, ГПа G, ГПа
0 197 82
20 197 -
100 197 80
200 186 77
300 175 74
400 168 71
500 - 67
600 - 62

A description of the physical symbols

Name Description
Е The normal elasticity modulus
r Density
l Coefficient of thermal conductivity
R UD. the resistivity

Technological properties

Name The value
Weldability Limited weldability; welding methods: SMAW, ADS submerged arc and gas protection electroslag welding. Recommended heating and subsequent heat treatment. The CCC without restriction.
Propensity to temper brittleness Tend not.
Forging temperature Start - 1250 °C, the end - 780 °C. the cross Sections up to 400 mm are cooled in air.
Flock-sensitive sensitivity not sensitive.
Workability by cutting In hot-rolled state when HB 158 and blower SB=640 MPa Kn TV.SPL.=1,2 Kn b.St.=1,2.

Our consultant will save your time

+49(1516) 758 59 40
E-mail:
Telegram:
WhatsApp:

Subscription

Special offers and discounts. :)